User's Manual

ManualsBrandsSystem X ManualsPaintballSystem X NME

TABLE OF CONTENTS / Section Page

Safety .......................................................................................................2

Warranty............................................................................................3

General Description.................................................................................3

Marker Component...................................................................................4

Specifications....................................................................................7

Operation..................................................................................7

Air Power..................................................................................................7

Preset

adjustable

Paintballs..............................................................................................7

Hopper

Paint

Regulators............................................................................................... 7

LPR

In-Line Regulator

Electronics............................................................................................. 8

Usage

Battery Information

Eye

On/Off

By Passing Eyes

General Usage Tips.................................................................................8

LED Colors and Meanings......................................................................9

Tournament Lock......................................................................................9

Trigger Programming...............................................................................9

Dwell

Debounce

Eye Mode

BIP Delay

ROF Cap

Eye Power

Programming Complete..........................................................................11

Equalink................................................................................11

Terminology...............................................................................11

Adjustment...............................................................................13

Feed Neck

LPR

In-Line Regulator

Trigger Adjustments

Bolt Adjustor

Maintenance............................................................................................1

General

Regulator

Troubleshooting..................................................................................... 14

System X "NME" Version 1.0

Summary of content (16 pages)

PAGE 1
LED Colors and Meanings......................................................................9 01 Safety .......................................................................................................2 Tournament Lock......................................................................................9 TABLE OF CONTENTS / Section Page Warranty............................................................................................3 System X "NME" Version 1.0 General Description...........
PAGE 2
02 WARNING/SAFETY WARNING This paintball marker is not a toy. Misuse or mishandling can result in serious injury or death. Anyone within range of a loaded paintball gun must wear eye protection specifically designed for paintball. You must be at least 18 years of age to purchase, 14 years old to use with adult supervision or 10 years old to use on paintball fields meeting ASTM standards F1777-97. Ensure you read entire instruction manual before operating your NME.
PAGE 3
WARNING/WARRANTY/GENERAL DESCRIPTION WARNING Make sure marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper paintball safety equipment. You will be held liable if someone is hurt by a paintball fired from your marker regardless of fault. WARRANTY System X warrants the NME against damages in manufacturing and defects. Electrical components are warranted for a period of 90 days.
PAGE 4
04 MARKER COMPONENTS
PAGE 5
1 Feed clamp: - 2 PC threaded feed clamp Held on to gun with o-ring. Serviceable 2 Body assembly: - 3D milled body. 10 Poppet spring: 11 Front block: Serviceable MARKER COMPONENTS 12 Volumizer: Serviceable - 016 o-ring. Serviceable - 2 015 o-rings. Serviceable - Front block screw: 10-32. - Front block barbs: 2 6-32 barbs. - 300 PSI gauge. - 3-way hose. 4 Barrel: - 2 PC 12" barrel (689 cal.) - Pull pin delrin bolt with 3 015 o-rings. Serviceable 3 Bolt: 5 Eye covers: with ball stoppers.
PAGE 6
06 MARKER COMPONENTS/SPECIFICATIONS 16. Frame: - 2 10-32 button head screws to mount frame to gun body. - Solenoid with 3 high flow barbs. - 2 m1.6 x .35 screws to hold solenoid down. - 1/8 magnet. - 8-32 shoulder screw to hold trigger down. - WAS board with harness, eye sensors and switch. - 2 m1.6x.35 screws to hold trigger switch down. - 2 nylon dowels to hold the board in place. - Button to activate board.
PAGE 7
SPECIFICATIONS MARKER COMPONENTS Low Pressure Regulator The low-pressure regulator (LPR) is mounted at the front of the front block. Small velocity adjustments could be made at the LPR. We recommend setting the LPR to the lowest possible pressure while maintaining operational consistency. Operating pressure for the LPR is between 50 and 100 psi. Operationally speaking, the lower the better, as when the pressure gets too high, the chances of internal air leaks increases and the recoil gets stronger.
PAGE 8
Anti Chop Eye 08 MARKER COMPONENTS/SPECIFICATIONS In-Line Regulator To turn on the NME powered by Equalizer, press and hold the power button (located on the back of the grip frame tray) for ½ of a second, and release it. The LED should light orange and stay that way for several seconds after releasing the button. The LED boot sequence is as follows: solid orange (booting), followed by solid green (normal mode) or solid red (competition mode).
PAGE 9
You can also change the tournament lock mode using the Equalink. It is necessary to remove the battery after changing the tournament lock or using the Equalink to alter settings or update firmware. MARKER COMPONENTS Because the Equalizer can easily exceed the feed rate of any loader in existence, it is recommended that you use a force-feed type of loader for the best possible performance.
PAGE 10
MARKER COMPONENTS/SPECIFICATIONS When you decide which programming feature you want to change, pull the trigger and hold it until the LED goes out, and then release the trigger. There will be a 2 second pause, and then the LED will flash the same color of the programming mode you are in (red=Dwell, green=Debounce™, orange=eye mode, etc.) the number of times that represents something associated with that feature.
PAGE 11
If you pull and release the trigger more than 4 times, then the LED will toggle green/red alternately to indicate there was a programming error, and then go back to the programming menu. The default Eye Mode is 1. BIP Delay™ Pull and release the trigger once for every 1ms of time you want the setting to be. For example, if you were programming the BIP Delay™ to 5ms, you would pull and release the trigger 5 times. The default BIP Delay™ setting is 10ms.
PAGE 12
MARKER COMPONENTS/SPECIFICATIONS Increasing your Dwell will increase the velocity of your marker. If you are experiencing a great variance in your chrono results, try increasing your Dwell and lowering your high pressure regulator. If your dwell is too low, consistency will suffer greatly. Debounce Debounce is the amount of time the trigger switch must be stable in the up position before checking for another trigger pull. This time is measured in milliseconds.
PAGE 13
MARKER COMPONENTS 2 Trigger adjustments: There are 3 adjustments to your trigger. 1 3 Warning DO NOT OVER PRESSURIZE the In-line regulator doing so might blow your solenoid and result in low ball velocity. Velocity adjustments are made at the in-line regulator. Velocity adjustments are achieved by turning the 3/16 allen screw clockwise. Warning DO NOT SCREW THE SET SCREW PAST FLUSH of the regulator body, doing so will over pressurize the regulator and damage the regulator pin.
PAGE 14
MARKER COMPONENTS/SPECIFICATIONS 1.Trigger tension. Your NME trigger uses magnetic force to return your trigger. To adjust the force behind the magnet simply turn the .050 allen screw located at the top of the trigger clockwise. To decrease the magnetic force turn the same screw counter clockwise. 2.Trigger travel. To take up the travel after the trigger switch has been activated locate the set screw in the middle of your trigger. Turn the set screw clockwise to the desired length.
PAGE 15
Gun consistently leaks down the barrel, decreasing slightly when bolt is pushed forward. . Heavy use of lightweight oil causes deterioration of Poppet O-ring and/or Cup Seal. Remove Poppet and replace O-ring. Remove and replace Cup Seal washer. Bolt moves freely reposition airline/lines . one or more of the airlines are crimped. Remove grip and Gun is pressurized and will not fire. readable. . Make sure the NME is turned on. . If eye's are enabled make sure there is a ball in the breach and .
PAGE 16
MARKER COMPONENTS/SPECIFICATIONS SYSTEM X 3330 SOUTH HARBOR BLVD. SANTA ANA, CA 92704 w w w . s y s t e m x .