User's Manual

ManualsBrandsSysgration ManualsElectronics4.3 wireless monitor

WVOS43

Digital Wireless

Observation System

PATENT PENDING

YOU WILL NEED:

● Voltage Meter

● Water proof sealant

● Drill with 1/8" drill bit

● Phillips head screwdriver

English

KEY FEATURES:

● Easy installation, ﬁ ts most applications

● 4.3" monitor comes with suction cup mount and

12 Volt DC plug for easy portability

● Camera connects to rear clearance light or 12V circuit

● WiSight

technology- no cable or wiring necessary

● No interference

● Signal transmits through and around objects up to 60+ feet away

● Sharp, clear, uninterrupted picture

● Expandable up to four wireless cameras (WVCMS130AP) and one Voyager wired camera

● Mirror or Normal View selectable

Package includes a 4.3" LCD color monitor, one 12 Volt DC accessory plug, one wired

camera cable input, a suction cup monitor mount, one rear color camera, stainless steel

hardware, and non-corrosive camera mounting bracket.

Summary of content (9 pages)

PAGE 1
WVOS43 Digital Wireless Observation System YOU WILL NEED: ● Voltage Meter ● Water proof sealant ● Drill with 1/8" drill bit ● Phillips head screwdriver KEY FEATURES: ● Easy installation, fits most applications ● 4.
PAGE 2
INSTALLING THE CAMERA 1. Choose a location close to the rear clearance lights so you can easily splice the power and ground connections. 2. Using a voltage meter, measure the clearance light wiring to determine positive/negative polarity. 3. Connect the red wire from the camera to the positive wire in the rear clearance lights. 4. Connect the black wire from the camera to the negative wire in the rear clearance lights. 5. Pre-drill the screw holes for the mounting bracket with an 1/8" drill bit.
PAGE 3
INSTALLING THE MONITOR 1. Plug power cable into the back of the monitor. 2. Attach the suction cup mount to the rear of the monitor with the supplied bracket. 3. Locate flat section of glass on your windshield (that does not block your vision) and apply suction cup. Snap the lever into the locked position (Figure 5). 4. Connect the power cord to a 12 Volt DC outlet. 5. Align the antenna to its upright position, parallel to the monitor. Figure 5 OPERATION 1.
PAGE 4
KEY FUNCTION 1 Power key 2 Select/Pair Key 4 Up Key 5 Down key 3 Menu key 1.POWER KEY - Press once to turn on the monitor. - Press again to turn off the monitor. 2.SELECT/PAIR KEY - Press the SELECT/PAIR key less 1 second, the channel will be changed. - Press the SELECT/PAIR key over 5 seconds, the pairing mode is enabling. 3.MENU KEY - Press less than 1 second enters the Contrast, Brightness, Color, Tint, Mirror, AutoPower, Dimming, Screen Saver and Scale Marker adjustment mode.
PAGE 5
Color Tint Mirror AutoPower Dimmimg Screen Saver Scale Marker EN-04
PAGE 6
4.UP AND 5.Down KEYS Function for Brightness, Contrast, Color, and Tint Control - Pressing “UP” key to increases brightness, contrast, color, or tint level when accessed menu adjust mode. - Pressing “DOWN” key to decreases brightness, contrast, color, or tint level when accessed menu adjust mode. Function for Mirror Control - Pressing “UP” key to change the mirror setting to ON or OFF when accessed menu adjust mode.
PAGE 7
Function for Scale Marker - Press “UP” or “DOWN” to change the Scale Marker mode. 1.OFF mode 2. Mode1 3. Mode 2 4. Mode 3 5. Mode 4 Function for Speaker Volume Control - Pressing “UP“ key to increases volume level. - Pressing “DOWN” key to decreases volume level.
PAGE 8
FCC IMPORTANT NOTE: 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 9
device that transmits or receives and you are experiencing difficulty in operating the system, the device(s) may be too close to either the WiSight Monitor or Camera. Change the placement to at least three feet between devices and re-test for proper operation. TROUBLE SHOOTING Monitor will not turn on. Monitor displays "No Signal". Intermittent reception. - Check power cord connection at monitor and 12VDC socket. - Check fuse in cigarette socket adapter. - Check 12VDC power at camera.