User's Manual

ManualsBrandsSysgration ManualsElectronicsNCS50 Display Commander

RV CONTROL AND MONITORING SYSTEM

Installation and Operation Manual

™

Patent # 9,679,644

Summary of content (20 pages)

PAGE 1
™ RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual Patent # 9,679,644
PAGE 2
PAGE 3
Important Safety Information Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could result in personal injury, including death. Do not operate while vehicle is being driven. The Mobile Application, Display Commander and/or Body Control Module should not be used while the vehicle is being driven.
PAGE 4
• TABLE OF CONTENTS TABLE OF CONTENTS ��3 INTRODUCTION ��4 Thank You! ��4 Features ��4 Precautions ��4 Packing List ��
PAGE 5
• INTRODUCTION • Thank You! Thank you for choosing iN-Command. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new iN-Command Lite for maximum enjoyment.
PAGE 6
• Mounting the Display Commander (DC) • INSTALLATION • Cut/Drill hole, allowing space below for future programming and behind for ventilation • Route wires through the hole and connect • Attach rear plate with screws • Check and ensure correct operation • Snap main unit into plate • Mount the unit using two #8 PH (0.164” x 0.5”) screws It’s a good idea to read all of the instructions before beginning the installation.
PAGE 7
• WIRING The wiring diagram depicts all the wiring connections required for proper operation of the unit. The TX (transmit) and RX (receive) connections at each device are crossed (crossover cable). BODY CONTROL MODULE (BCM) CONNECTIONS PIN NO. WIRE GAUGE PIN NO.
PAGE 8
• APP SETUP MENU LIST One light group and seven motor functions can be added or removed via a downloadable App from Google and Apple stores. Motor functions may include slides, awnings, jacks, or any motor that may be controlled with a momentary switch. Refer to the Wiring Diagram and Terminal List when installing new equipment.
PAGE 9
• TRAVEL LOCKOUT (SAFETY) iN-Command is equipped with a Travel Lockout feature to ensure certain system functions are unavailable during transit. When the Brake on the vehicle is activated, iN-Command will lock out (disable) all motorized functions. If the Switch Plate (SP) is installed, the Travel Lock LED will be solid red. If the DC is installed, Travel Lock text will appear.
PAGE 10
• TROUBLE SHOOTING Symptom Solution Verify the BCM is powered on. Display Commander (DC) will not turn ON Check main fuse in Distribution Panel. Check 12V+ on wire to DC (RED wire). Check Ground wire to DC. Check if the Red power LED is off, No power to the Body Control Module (BCM) Check the fuse in the Distribution Panel. Check 12V+ on wire at pin 36. Check Ground wire at pin 34. Cycle power to the BCM and DC. Ensure the wires to the BCM and DC are connected and there is 12V.
PAGE 11
• SWITCH PLATE BUTTONS The SP (Switch Plate) has 2 buttons on the front of it. From left to right, they are: • Travel Lock • Bluetooth Pairing The Travel Lock button turns off the Travel Lock function when the light is flashing red. The Bluetooth Pairing button is used to pair and unpair the mobile app to and from the SP. • DISPLAY COMMANDER BUTTONS The DC (Display Commander) has 5 buttons on the front of it.
PAGE 12
• SPECIFICATIONS • Federal Communications Commission (FCC) Statement NCS50DC (Display Commander) Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC Maximum Current Draw . .. . . . . . . . . . . . . . . .. . . .200mA@12VDC Minimum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 9VDC Maximum Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . 16VDC NSC50 (Body Control Module) Operating Voltage . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
• MOBILE DEVICES: iN-Command Lite is able to pair to Android and iOS devices via the mobile App. Visit the Google Play and Apple App stores on your mobile device to download and use the iN-Command Lite App. Only One mobile device is able to be paired with iN-Command Lite.
PAGE 14
• Pairing Mobile Device to DC/SP 1. Open NCS Lite application on device. 3. Press “Select” button to connect the SP or DC. 2. Press the gear cog to enter the settings page. 4. Press device name to connect.
PAGE 15
5. Remote device will show pairing message. The SP will flash a blue light. The DC will flash " Accept new device on display" Press "ENTER" or "BLUETOOTH PAIRING" button to Pair. 6. If connection is successfully established, setting page will show connected device name and versions. To connect NCS50DC/SP with another device. NCS50SP : Long press“BLUETOOTH PAIRING” button for 7~10 seconds to unpair device. If unpairing is successful, NCS50SP will flash blue light twice.
PAGE 16
• NCS50DC/SP FIRMWARE UPDATE* 1. Press “Update” button to update NCS50DC/NCS50SP. 2.2 For Android: Wait for Wi-Fi connection, then press start button. 2.1 For iOS: In Wi-Fi Settings, connect to Wi-Fi network shown on app. Password is “1234567890”. 3. For iOS : Once connected to network, go back to app, App will automatically start firmware update.
PAGE 17
• EDIT AND RESET FLOOR PLAN 4. App will display "Update complete" once firmware is update Press Dismiss button. DC/SP will reboot with new firmware. 1. From the Apps Home Page, press the gear cog at the lower right corner to enter the Settings Page. 5. BCM update: Press update button next to BCM version. BCM update will begin automatically. 2. From the Settings Page, you can "Edit Menu", "Load Default Menu", "Load DC Menu" and "Push Settings to DC Menu".
PAGE 18
3. To Edit the floor plan, press the Edit button. 5. To add or remove functions, press the box next to the function. 4. In the Edit Menu, you can add or remove functions, reposition function and edit the text for the function. 6. To reposition a function, press and hold the "≡" icon next to the function. Drag to move the function to a new location. The "Light" function is shown as an example.
PAGE 19
7. To edit the text, press on the function text. A device rename window will open. Press "OK" after completing text editing. (The text box is Limited to 12 characters) 8. Once changes have been made, press the Save button at the top of the page. 9. After the floor plan has been edited, the new floor plan settings can be pushed to the DC/SP. Press "Set" Push Settings to DC Menu". 10.