DATA SHEET RF Engine 200 Series Model Number: RF200, Part Numbers: RF200PD1 and RF200PF1 ©2008-2014 Synapse, All Rights Reserved. All Synapse products are patent pending. Synapse, the Synapse logo, SNAP, and Portal are all registered trademarks of Synapse Wireless, Inc. Doc# 430133-01C 6723 Odyssey Drive // Huntsville, AL 35806 // (877) 982-7888 // Synapse-Wireless.
Table of Contents 1. 2.
1. RF Engine 200 Series Modules Overview The RF Engine 200 Series (Model Number RF200) is an IEEE 802.15.4, low power, highly-reliable solution to embedded wireless control and monitoring network needs that require high data rates. The RF200 embeds Synapse’s SNAP OS, the industry’s first Internet-enabled, wireless mesh network operating system into the Atmel ATmega128RFA1 single-chip AVR® microcontroller with an integrated transceiver that delivers up to 2Mbits/sec.
Figure 1.
Specifications Table 1.1: RF200PD1/RF200PF1 Specifications RF200PD1: Up to 3 miles at 250Kbps Outdoor LOS Range RF200PF1: Up to 2.5 miles at 250Kbps Performance Power Requirements General Transmit Power Output 15 dBm RF Data Rate 250Kbps, 500Kbps, 1Mbps, 2Mbps Receiver Sensitivity -103 dBm (1% PER) Supply Voltage 2.7 - 3.6 V Transmit Current (Typ@3.3V) 80mA Idle/Receive Current (Typ@3.3V) 20mA Power-down Current (Typ@3.3V) 1.6uA Frequency ISM 2.
Module Pin Definitions Table 1.
Electrical Characteristics Table 1.3: RF200PD1 / RF200PF1 DC Characteristics at 25° C Symbol Parameter Condition Min Typ Max Units VCC 1 Supply Voltage 2.7 TOP Operating Temp TSTOR Storage Temp VIH Input Hi Voltage All Digital Inputs VIL Input Low Voltage All Digital Inputs VOL Output Low Voltage VOH Output High Voltage ILIN In Leakage Current VIN=VCC or VSS, all Pins TX-ICC Transmit Current VCC = 3.3V 80 mA RX-ICC Receive Current VCC = 3.
Table 1.5: ADC Timing/Performance Characteristics Symbol Parameter RAS Source impedance at input4 RES Conversion Resolution Condition Min Typical Max 3k Single Ended CLKADC <= 4MHz 10 Single Ended CLKADC > 8MHz 8 Unit kΩ Bits DNL Differential non-linearity VREFH = 1.6V CLKADC=4MHz INL Integral non-linearity VREFH = 1.6V CLKADC=4MHz EZS EG -0.5 LSB 0.8 LSB Zero-scale error 1.5 LSB Gain error 1 LSB Mechanical Drawings These drawings in Figure 1.
Figure 1.2: Mechanical drawings of the RF200PD1 and RF200PF1 Modules Board Mounting Considerations The RF200PD1 and RF200PF1 modules are designed to mount into a receptacle (socket) on the host board. Figure 1.3 shows an RF200PD1 module plugged in to a host board. The receptacle sockets are on standard 2mm centers.
Figure 1.
2. Agency Certifications United States (FCC) The Model SM220 modules comply with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required. In order to comply with FCC Certification requirements, the Original Equipment Manufacturer (OEM) must fulfill the following requirements. 1. The system integrator must place an exterior label on the outside of the final product housing the RF200 Modules. Figure 2.
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Canada (IC) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Since the 2400-2483.5 MHz band is not harmonized by a few countries throughout Europe, the Restriction sign must be placed to the right of the CE marking as shown in the drawing. Labeling requirements for Industry Canada are similar to those of the FCC. A clearly visible label on the outside of the final product housing must display the contents shown in Figure 2.2 below. MANUFACTURERSNAME BRANDNAME or TRADENAME MODEL: Contains RF200 IC: 7084A-RF200 Figure 2.
MANUFACTURERSNAME BRANDNAME or TRADENAME Contains RF200 FCC ID: U90-RF200 Contains RF200 IC: 7084A-RF200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation. Figure 2.
