FLAT PANEL BOTTOM VENT ELECTRIC FIREPLACE with digital display and remote control OWNER’S MANUAL AC 120V 60Hz 1500W
IMPORTANT SAFETY INFORMATION! WARNING ⚫ Read all instructions before using this heater! ⚫ The air vent for this heater is in the bottom of the unit. When in heater mode, the air vent will release hot air and the vent portion will be hot. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.
WARNING ⚫ For residential use only! NOT for commercial use! Any commercial or public use of this heater videos all warranties and could cause injury. ⚫ This product is not intended to be a primary heater source. It is for supplemental heat only. ⚫ INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! ⚫ Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ⚫ NEVER modify this heater. Doing so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grounded for wall-hanging or recessing use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape measure; electric drill; 1/4” wood drill bit, hammer.
Wall Mounted Installation ⚫ Remove the back-bracket’s screws from fireplace and remove the both side two white screws. ⚫ Remove the front tempered glass out of appliance and take foam (H) out of appliance. NOTE: It is strongly Recommended that the mounting bracket(E) be screwed into the wall studs where possible. If the wall studs cannot be used, ensure that the supplied plastic anchors are used to affix the bracket to the wall and the bracket are adequately secured.
A. Fasten the metal bracket at the back of fireplace with 2pc 4x8mm screw, the other end to the wall with 2pcs of Drywall anchors.
B. With the wall mounting bracket installed have two people lift the appliance up and insert the two hooks on the bracket into the two slots on the back of the appliance. C. Fix the tempered glass with 4pcs of 4*8mm white screws provided D. Check the appliance for stability ensuring that the bracket will not pull free from the wall.
WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure do to so could result in electric shock, fire, serious injury, or death. Power Plug the power cord into a 110-120V Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit.
Manual /Remote control Operation BUTTON FUNCTION ACTION&INDICATION Enable all functions and turn off all functions on control 1. This button should switch on. 2. Enable all functions and turn off all functions on control FLAME button: Makes flame effect dimmer and brighter. NOTE: Flame effect stays on until power button is turned off. Flame effect must be on for heater to turn on. 1. Press once. Flame brightness effect changes. 2. Press again. Until desired setting is reached.
Remote control requires one 3V CR2025 Lithium Cell Battery (included and pre-installed). Remove the protective sheet between the battery and the contacts in order to operate (see Fig 1. and Fig.2). REPLACE THE REMOTE CONTROL BATTERY When the remote-control stops operating, or its range seems reduced. It is time to replace the battery with a new one. 1. The battery compartment is located on the back end of the remote. 2. Press and slide the battery door open and remove the old battery. 3.
Buff using a soft non-abrasive cloth, slightly dampened with water. ⚫ DO NOT use brass polish or household cleaners as these products will damage the metal trim. Glass: • Use a good quality non-abrasive glass cleaner and dry thoroughly with a paper towel or lintfree cloth. • NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface. • Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
WARNING DISCONNECT THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. CONTACT A QUALIFIED ELECTRICIAN OR TECHNICIAN SHOULD THIS ELECTRIC APPLIANCE NEED SERVICE OR REPAIR. Problem 1. Fireplace turns off and will not turn on. Flame is not moving. 3 Flame is not visible. 4 Log set and /or is not glowing. 5 Remote control does not work. Possible Cause 1. Fireplace has overheated and safety devise has caused thermal switch to disconnect or home circuit breaker has opened. 1.Loose wiring. 2.
