9 CONTACT INFORMATION
IMPORTANT SAFETY INSTRUCTION A WARNING These instructions should be carefully read before installation and retained by the user. The booklet must be kept and delivered to the new user in case of disposal of the heater. The Manufacturer reserves the right to vary the features of the product without prior notice. The technical data are indicative only. 1. THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF TOUCHED. 2.
18. Always unplug appliance when not in use. 19. Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been dropped or damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical adjustment, or repair. 20. Do not use appliance outdoors. 21. Never place appliance where it may fall into a bathtub or other water container. 22. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, etc.
Style A
A B C
1.1 DIMENSIONS II _J A(mm) B(mm) C(mm) D(mm) E(mm) A(in.) B(in.) C(in.) D(in.) E(in.) 914 460 771 98 420 36 18.11 30.35 3.86 16.54 1066 460 922 98 420 42 18.11 36.30 3.86 16.54 1270 460 1126 98 420 50 18.11 44.33 3.86 16.54 1524 460 1380 98 420 60 18.11 54.33 3.86 16.
C A{mm) B(mm) C(mm) A(in.) B(in.) C(in.) 785-895 80-90 430-450 31-35.2 3.15-3.54 16.93-17.7 935-1045 80-90 430-450 36.82-41.1 3.15-3.54 16.93-17.7 1140-1250 80-90 430-450 44.9-49.2 3.15-3.54 16.93-17.7 1390-1505 80-90 430-450 54.75-59.2 3.15-3.54 16.93-17.
NOTE: * The size of column B reserves some space for the main power switch on the top, you can also choose 3.54inch for full embedding, since the touch screen also has a main power switch. * Please leave enough space to pace the power cord on the right side of the fireplace. LISTING APPROVALS This appliance has been tested in accordance with the ETL Standards for fixed and location-dedicated electric room appliances in the United States and Canada.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULTCAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHERFLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE. HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED. AS IT MAY CREATE A FIRE HAZARD. Follow all National and local electrical codes. 1.
2
*OTUBMMBUJPO 0QUJPO 8BMM )BOHJOH
Two left and right M5X12 ̙ ̙ Bx5 Ax5 by " #
use the screw we removed from step 2.
HPHHMFT ɓ use the screw we removed from step 1.
Installation - Built in Construction Step 1. Removing the Glass Frame Step 2. Removing the Mounting Bracket (Step 1 and Step 2 please refer to page 13-14 same as Wall Hanging Installation.
# CZ Ax2 ̙ " ̙ Bx2
HPHHMFT Connect the data cable connector ɓ use the screw we removed from step 1.
UIF SFQMBDF .
5.2 CONTROL PANEL/ REMOTE CONTROL OPERATION (Main Power Switch must be turned ON before using remote control.) The touch display panel is shown on the bottom right of the front of the appliance. ♦ Move the battery's transparent insulating piece away before using remote control. -----Air Inlet Heater Vent DIMMER Remote Receiver For model LC FL.AME SPEED HEAT TIMER POWER ON/OFF □ ••••••• Display Heater Flame Speed i..
Control the Heater. Press button to initiate the heater. HEATER (OFF) no heater or blower. � ( - ), heater blows warm air(750W) ( -- ), heater blows hot air(1500W) NOTE: Heater functions cycle from (OFF) ( - )( -- ) Control the flame color. COLOR A � 12 Settings: 1.red 2.yellow 3.blue 4.orange 5.red & yellow 6.red & blue7.red & white 8.yellow & blue 9. yellow & white 10.blue & white 11.red & yellow & blue 12.
5IF IFBUFS NBZ FNJU B TMJHIU IBSNMFTT PEPS XIFO STU VTFE 5IJT JT B OPSNBM DPOEJUJPO DBVTFE CZ JOJUJBM IFBUJOH PG UIF JOUFSOBM QBSUT BOE XJMM OPU PDDVS BHBJO
7.2 SCHEMATIC DIAGRAM LAMP PCB FOR FLAME BED ••••••• [88]6 Key board E sa:i LAMP PCB FOR FLAME -Ct- 0 (/) 0 C:Cl.. (tl ,._ ,._ .... 0 I- IC Power supply G¢---=i_ L N AC-N 0 [[[[ eo 7 c 1 - - 7 Q) Q) Power Switch □ Receptor PCB for Remote Controller TEMPERATURE SENSOR 0 :1 1: L - - J Temperature Limit Control (PTC Type Thermostat) 8.
