Installation Guide

ManualsBrandsSymmons ManualsBathAllura 2-Handle 1-Spray Tub and Shower Faucet with Hand Shower in Chrome (Valve Included)

Model Numbers Speciﬁcation

Options/Modiﬁcations

Tub/shower trim with hand shower and lever handle

includes wall connection, cradle for hand shower

mounting, in-line vacuum breaker, exible metal hose,

non-diverter tub spout, 3 mode hand shower and 3

mode showerhead with standard 2.5 gpm (9.5 L/min)

ow restrictor. Shower trim with hand shower and lever

handle includes all of the above less non-diverter tub

spout. Valve trim with hand shower and lever handle

includes all of the above less non-diverter tub spout and

3 mode showerhead. Components made from metal

and nonmetallic materials plated in standard polished

chrome nish.

Allura

Trim Series

Operation & Maintenance Manual

4703-TRM, 4705-TRM, 4706-TRM

4703-TRM

Valve Trim with Hand Shower

Compliance

-1.5

1.5 gpm (5.7 L/min) ﬂow restrictor

-2.0

2.0 gpm (7.6 L/min) ﬂow restrictor

-LAM

Metal ﬁnish insert handle

-LR

Lever handle

4705-TRM

Shower Trim with Hand Shower

Note: Append appropriate -sufx to model number.

-STN

Satin Nickel ﬁnish

-ASME A112.18.1; CSA B125.1

4706-TRM

Tub/Shower Trim with Hand Shower

-H323-V

30” slide bar in place of wall cradle on hand

shower units

-SS

Slip spout on any tub and shower unit

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Summary of content (6 pages)

PAGE 1
4703-TRM, 4705-TRM, 4706-TRM Allura® Trim Series Operation & Maintenance Manual Model Numbers 4703-TRM Valve Trim with Hand Shower 4705-TRM Shower Trim with Hand Shower 4706-TRM Tub/Shower Trim with Hand Shower Options/Modifications -1.5 1.5 gpm (5.7 L/min) flow restrictor -2.0 2.0 gpm (7.
PAGE 2
Dimensions A A B C B D D C F E E F G H I J K J L G H M N O P Q I R N O M L P Q K Floor S Notes: 1) All dimensions measured from nominal rough-in (see R as reference). 2) Dimensions subject to change without notice. 2 S R Measurements Ø 2 1/2”, 64 mm 6 3/4”, 172 mm 2 1/8”, 54 mm Male 1/2” NPT thread must be recessed 1/4” from finished wall 6”, 152 mm right or left Ref. 77”, 1956 mm Ø 7”, 178 mm Ø 5”, 127 mm 10”, 254 mm 4 3/4”, 121 mm 2 1/2”, 64 mm Ref. 32”, 813 mm (4706-TRM) Ref.
PAGE 3
Parts Breakdown Replacement Parts Item A E D B B C N D O P C A L K M I H F U R Q G S I H F L T E F G H I J K* L M N O P Q R S L T* U V W J Description In-line Vacuum Breaker Wall Elbow Showerhead Shower Arm (flange included) Flange Plug Button Handle Screw Star Washer Handle Dome Cover Diverter Escutcheon Mounting Screws Mounting Plate Wall Cradle Cradle Hardware Cradle Mount Diverter Dome Cover Lock Nut Dial Mounting Screws Shower Escutcheon Hand Shower Tub Spout 5” Hose with Vaccum B
PAGE 4
Installation Note: For valve body installation, please see valve body manuals. 1) Install shower escutcheon (T) to shower valve (4000-BODY). Secure with two screws (L). Snap dial (S) into shower escutcheon. 3) A ttach diverter escutcheon (K) to plastic mounting plate (M). 6) Install diverter handle (4705-TRM and 4706-TRM only) and shower handle (I) to valves. Secure handle(s) with star washer (H) and screw (G). Attach plug button (F) to handle(s).
PAGE 5
Installation 8) Install wall elbow (B) to pipe fitting. Tighten set screw to secure. 10) R emove cover of wall cradle (N). Install cradle mount (P). Secure with three screws (O). Replace cover on hand shower cradle. 12) Install showerhead (C) to shower arm (D) turning clockwise to tighten. 1 D B 1 N 1 2 P O 13) Attach large end of hand shower hose (W) to hand shower (U). Connect in-line vacuum breaker to wall elbow (B). Turn clockwise to tighten.
PAGE 6
Operation & Maintenance Temperature Control Diverter Control 1) Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position. 2) Turn shower handle counterclockwise approximately 1/2 turn to put valve in warm position. 1) Diverter handle facing straight down is for diverter function 1. 2) 4 705-TRM: Turn diverter handle counterclockwise one full revolution for diverter function 2. 706-TRM: Turn diverter handle counterclockwise 1/4 4 turn for diverter function 2.