GOT-5100TL All-in-One 10.
Disclaimers This manual has been carefully checked and believed to contain accurate information. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.
Safety Approvals CE Marking FCC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are meant to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications.
Safety Precautions Before getting started, please read the following important safety precautions. 1. 2. 3. 4. 5. 6. 7. 8. iv The GOT-5100TL does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any staticshielded devices.
Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. When handling boards and components, wear a wristgrounding strap, available from most electronic component stores. Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Table of Contents Disclaimers.................................................................................... ii Safety Approvals ...........................................................................iii Safety Precautions ....................................................................... iv CHAPTER 1 INTRODUCTION ..........................................................1 1.1 General Description.....................................................1 1.2 Specifications .........................
3.13 3.14 3.15 Set Supervisor/User Password..................................44 Save & Exit Setup......................................................45 Exit Without Saving ...................................................46 CHAPTER 4 DRIVERS INSTALLATION..........................................47 4.1 System.......................................................................47 4.2 Touch Screen ............................................................48 4.2.1 Specification (GOT-5100TL) ..........
MEMO viii
GOT-5100TL User’s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the GOT-5100TL. Chapter 1 includes the following sections: General Description Specification Dimensions I/O Outlets Package List 1.1 General Description The GOT-5100TL is a fan-less and compact-size touch panel computer, equipped with an 10.4” TFT LCD display and low power consumption AMD LX800 processor with FSB 500MHz. The GOT® ® ® 5100TL supports Windows XP, Windows CE.
GOT-5100TL User’s Manual Embedded O.S. Supported ® The GOT-5100TL not only supports Windows XP, but also ® supports embedded OS, such as Windows CE.NET, and ® Windows XP embedded. For storage device, the GOT-5100TL supports CompactFlash™ card. Industrial-grade Product Design The GOT-5100TL has an incredible design to be used in different industrial harsh environments. l A fuse helps prevent over-voltage for power input. l The front bezel meets the IP65/NEMA4 standard.
GOT-5100TL User’s Manual 1.2.2 l I/O System Standard I/O One RS-232 and one RS-232/422/485 Two USB 2.0 l Ethernet One RTL8139DL Fast Ethernet l Audio Line-out l Expansion One Mini-PCI l Storage One slot for CF card l Box-header One PATA-100 IDE 1.2.3 System Specification l 10.4” TFT LCD l Heat Dispensing Design l Disk drive housing: one 2.5” PATA drive (option) l Net Weight 1.6 Kgs (3.52 lb) l Dimension (Main Body Size) 293x 44.
GOT-5100TL User’s Manual NOTE All specifications and images are subject to change without notice.
GOT-5100TL User’s Manual 1.3 Dimensions This diagram shows you dimensions and outlines of the GOT-5100TL.
GOT-5100TL User’s Manual 1.4 I/O Outlets Please refer to the following illustration for I/O locations of the GOT5100TL. No 6 Function 1 POWER SWITCH (AT) 2 24VDC POWER 3 VGA 4 COM 2 (RS-232) 5 COM 1 (RS-232/422/485) 6 1 X ETHERNET (RJ-45) 7 2 X USB 2.
GOT-5100TL User’s Manual 1.5 Packing List When you receive the GOT-5100TL, the bundled package should contain the following items: l l l l l l l l GOT-5100TL x 1 Panel Mount Kit x 6 Driver CD x1 Wall-Mount Kit x1 Wireless LAN kit (optional) 2.5” HDD kit (optional) Desktop Stand Kit (optional) VESA ARM(optional) If you have any demand for the optional items or any items are missing, please contact AXIOMTEK distributors immediately.
GOT-5100TL User’s Manual CHAPTER 2 HARDWARE INSTALLATION The GOT-5100TL provides rich I/O ports and flexible expansions for you to meet different demand, for example, CF card. The chapter will show you how to install the hardware. It includes: CompactFlash™ Card Serial Port Ethernet Mounting Way 2.1 CF card Installation The GOT-5100TL provides one CF slot for users to install CompactFlash™ card.
GOT-5100TL User’s Manual Step 2 Find out the cover on the side of the system. Step 3 Locate the CompactFlash the socket.
GOT-5100TL User’s Manual 2.2 Serial Ports Interface The GOT-5100TL has two onboard serial ports, COM1 (RS232/422/485) and COM2 (RS-232).
GOT-5100TL User’s Manual COM2 COM1 When COM1 is set to RS-422 or RS-485, the pin assignments are listed below: Pin # Signal Name RS-422 RS-485 1 TX- DATA- 2 TX+ DATA+ 3 RX+ No connector 4 RX- No connector 5 No connector No connector 6 No connector No connector 7 No connector No connector 8 No connector No connector 9 GND GND Hardware Installation 11
GOT-5100TL User’s Manual 2.3 Ethernet The GOT-5100TL is equipped with a high performance Plug and Play Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
GOT-5100TL User’s Manual 2.4 Mountings – Panel/Wall/Desktop/VESA There are several mounting ways for the GOT-5100TL, Panel, Wall, Desktop and VESA mountings. 2.4.1 Panel Mounting The GOT-5100TL is designed for panel mount application. A set of standard mounting kit are bundled with the system package that you can use it to mount the GOT-5100TL.
GOT-5100TL User’s Manual 2.4.2 Wall-Mounting The GOT-5100TL is designed for Wall mounting application. Please refer to the following steps: Find out the screws as marked on the back side of chassis.
GOT-5100TL User’s Manual 2.4.3 Desktop-Mounting The GOT-5100TL is designed for desktop mounting application. Please refer to the following steps: Step 1 Find out the screws as marked on the back side of chassis.
GOT-5100TL User’s Manual Step 2 16 Assemble the desktop stand to the chassis, and fix the screws.
GOT-5100TL User’s Manual 2.4.4 VESA-ARM Mounting Step 1 Find out the screws as marked on the back side of chassis. Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the screws.
GOT-5100TL User’s Manual Step 3 18 VESA mounting Installation completed.
GOT-5100TL User’s Manual 2.5 HDD Installation The GOT-5100TL provides a convenient drive bay module for users to install 2.5” IDE HDD. Please follow the steps: 1. Unscrew screws to remove the rear chassis. 2. Unscrew 4 screws from the HDD drive bracket, and take out HDD bracket kit to install 2.5” HDD.
GOT-5100TL User’s Manual 3. Installation complete.
GOT-5100TL User’s Manual 2.6 Wireless Card Installation The GOT-5100TL provides one miniPCI slot for user to install one wireless card. W hen installing the wireless card, refer to the following instructions and illustration: 1. Open the back cover and find mainboard (EP621). 2. Install miniPCI wireless card.
GOT-5100TL User’s Manual 3. There are two connectors on wireless LAN card. One is MAIN, and the other is AUX. Connect antenna cable to MAIN connector on wireless LAN card.
GOT-5100TL User’s Manual MEMO Hardware Installation 23
GOT-5100TL User’s Manual CHPATER 3 PHOENIX-AWARD BIOS UTILITY The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off. 3.1 Entering Setup There are two ways to enter the Setup program.
GOT-5100TL User’s Manual 3.
GOT-5100TL User’s Manual 3.4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to configure then press to accept or enter its sub-menu.
GOT-5100TL User’s Manual 3.5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use or key to select the value you want in each item. l Date The date format is , . Press to show the calendar. day It is determined by the BIOS and read only, from Sunday to Saturday. date It can be keyed with the numerical/ function key, from 1 to 31.
GOT-5100TL User’s Manual computer. There are 45 predefined types (Type 1 to Type 45) and 2 user’s definable types (Type User) for Enhanced IDE BIOS. Press /<+> or /<−> to select a numbered hard disk type, or directly type the number and press . Please be noted your drive’s specifications must match the drive table. The hard disk will not work properly if you enter improper information.
GOT-5100TL User’s Manual 3.6 Advanced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference. l First/Second/Third Boot Device st nd rd These items let you select the 1 , 2 , and 3 devices that the system will search for during its boot-up sequence. The wide range of selection includes USB-CDROM, HDD-0, HDD-1, and so on.
GOT-5100TL User’s Manual Gate A20 Option The default value is “Fast”. l Normal The A20 signal is controlled by keyboard controller or chipset hardware. Fast Default: Fast. The A20 signal is controlled by Port 92 or chipset specific method. Typematic Rate Setting This item determines the typematic rate of the keyboard. The default value is “Disabled”. l Enabled Enable typematic rate and typematic delay programming. Disabled Disable typematic rate and typematic delay programming.
GOT-5100TL User’s Manual Small Logo(EPA) Show If enabled, the EPA logo will appear during system booting up; if disabled, the EPA logo will not appear. Press to return to the Main Menu page.
GOT-5100TL User’s Manual 3.7 Advanced Chipset Features This section contains completely optimized chipset’s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. l CPU Frequency Use this item to set the CPU Frequency with these options: Auto, 333MHz, 400MHz, 433MHz and 500MHz. The default setting is “Auto”.
GOT-5100TL User’s Manual l Output Display This item allows you to choose the output for your system display. Configuration options are “CRT”, “Flat Panel” and “Panel & CRT”. The default value is “Panel & CRT”. l Flat Panel Configuration The configuration is for resolution of flat panel which locks to 800 × 600. Press twice to return to the Main Menu page. 3.8 Integrated Peripherals This section allows you to configure your SuperIO Device, IDE Function and Onboard Device.
GOT-5100TL User’s Manual l Super IO Device Scroll to this item and press to view the sub menu Super IO Device. Onboard Serial Port 1/2/3 Select an address and corresponding interrupt for the serial port. Options: 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ10, 2E8/IRQ11, 338/IRQ5, 238/IRQ7, Auto and Disabled. Press to return to the Integrated Peripherals page.
GOT-5100TL User’s Manual l IDE Function Setup Scroll to this item and press to view the sub menu IDE Function Setup. Master/Slave Drive PIO Mode The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 to 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.
GOT-5100TL User’s Manual block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. Press to return to the Integrated Peripherals page. l Onboard Device Scroll to this item and press to view the sub menu Onboard Device. Onboard Audio Use this item to enable or disable the onboard Audio function. Onboard USB1.1 Enable this item if you are using the EHCI (USB1.1) controller in the system. Onboard USB 2.
GOT-5100TL User’s Manual l ITE8888 Configure Scroll to this item and press to view the sub menu ITE8888 Configure. Press twice to return to the Main Menu page.
GOT-5100TL User’s Manual 3.9 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity. l ACPI Function This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The function is always “Enabled”. l Power Management This option allows you to select the type of power Management. Options are: “APM”, “ACPI”.
GOT-5100TL User’s Manual enter the SUSPEND mode. l HDD Power Down If HDD activity is not detected for a specified length of time in this field, the hard disk drive will be powered down while other devices remain active. l Modem Use IRQ If you want an incoming call on a modem to automatically resume the system from a powersaving mode, use this item to specify the interrupt request line (IRQ) used by the modem.
GOT-5100TL User’s Manual 3.10 PnP/PCI Configuration Setup This section describes the configuration of PCI (Personal Computer Interconnect) bus system, which allows I/O devices to operate at speeds close to the CPU speed while communicating with other important components. This section covers very technical items that only experienced users could change default settings. l PNP OS Installed Select Yes if the system operating environment is Plug-and-Play aware (e.g., Windows 95). The default value is “No”.
GOT-5100TL User’s Manual l Resources Controlled By The Phoenix-Award Plug and Play BIOS can automatically configure all boot and Plug and Play-compatible devices. If you select Auto, all interrupt request (IRQ), DMA assignment, and Used DMA fields disappear, as the BIOS automatically assigns them. The default value is “Manual”. l IRQ Resources When resources are controlled manually, assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt: 1.
GOT-5100TL User’s Manual 3.11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. Current SYSTEM Temp Show you the current system temperature. Current CPU Temp The current system CPU temperature will be automatically detected by the system. Vcore 2.5V/3.3V/+12V/VBAT(V) Show you the voltage of 2.5V/3.3V/+12V/VBAT. l l l Press to return to the Main Menu page.
GOT-5100TL User’s Manual 3.12 Load Optimized Defaults This option allows you to load your system configuration with default values. These default settings are optimized to enable high performance features. To load CMOS SRAM with SETUP default values, please enter “Y”. If not, please enter “N”.
GOT-5100TL User’s Manual 3.13 Set Supervisor/User Password You can set a supervisor or user password, or both of them. The differences between them are: 1. 2. Supervisor password: You can enter and change the options on the setup menu. User password: You can just enter, but have no right to change the options on the setup menu. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.
GOT-5100TL User’s Manual 3.14 Save & Exit Setup This section allows you to determine whether or not to accept your modifications. Type “Y” to quit the setup utility and save all changes into the CMOS memory. Type “N” to bring you back to the Setup utility.
GOT-5100TL User’s Manual 3.15 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session. Type “Y”, and it will quit the Setup utility without saving your modifications. Type “N” to return to the Setup utility.
GOT-5100TL User’s Manual CHAPTER 4 DRIVERS INSTALLATION 4.1 System GOT-5100TL supports Windows 2000/XP. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing. 1. Insert Driver CD and select the “\ GOT-5100TL Driver CD\”. 2. Select all files and follow the installing procedure.
GOT-5100TL User’s Manual 4.2 Touch Screen 4.2.1 Specification (GOT-5100TL) Touch Screen 5-wire Analog Resistive type Touch Screen Controller PenMount DMC9000 Touch Screen Controller IC Communications RS-232 Baud Rate 19200 baud rate fixed Resolution 1024 x 1024 (10 bit A/D converter inside) Power Input 2.7V ~ 5.5V Power Consumption Active: 3.6mA / Idle Mode: 1.0mA 4.2.
GOT-5100TL User’s Manual 3. Click Start menu and select “PenMount Utilities”; and then, a “PenMount Control Panel” pops out. Note Please choose COM3 for touch screen installation.
GOT-5100TL User’s Manual 4. Select the “Standard Calibrate” tab. 5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. 6. Press OK.
GOT-5100TL User’s Manual 4.3 Embedded O.S. 4.3.1 Windows XP Embedded Here are supported onboard devices: n Onboard Multi I/O Floppy drive 16C550 UARTs compatible serial port IrDA for wireless communication n Onboard IDE IDE HDD n USB n PS2 Keyboard and mouse n CRT/LCD display(Default 18bits Resolution 800x600) n 10/100 base-T Ethernet n Compact Flash n Onboard Audio n Touch Screen PenMount Touch screen GOT-5100TL has Penmount touch screen on COM3, which is disabled by default.
GOT-5100TL User’s Manual 4.3.2 Windows CE.NET 5.0 Here are supported onboard devices: n Onboard Multi I/O Floppy drive 16C550 UARTs compatible serial port IrDA for wireless communication Onboard IDE n IDE HDD n USB n PS2 Keyboard and mouse n CRT/LCD display n 10/100 base-T Ethernet n Compact Flash n Onboard Audio n Audio n Touch Screen Calibration Touch screen In this image we add PenMount Touch drivers and utilities. It is customized for 800 x 600. Calibration: 1.
GOT-5100TL User’s Manual Appendix The solution for removing exclamation points on two COM4. After installing XP, it sometimes appears two COM4 (or one COM4 and one COM5) with exclamation points. To remove them, please follow the steps below. In device manager, it appears two COM4 with exclamation points. Remove COM1, COM2 and COM4, and then restart W indows.
GOT-5100TL User’s Manual 1. After restarting windows, you can see two COM4 (or one COM4 and one COM5) with exclamation points in device manager. 2. Choose first COM4 and enter properties→ resources→Set Configuration Manually Untick the “Use automatic settings” 1. Setting based on : Basic configuration 0000 2. IRQ: 04 (COM1) 3.
GOT-5100TL User’s Manual 1. Enter properties →port setting→ Advanced 2. COM Port Number: COM1 (in use) 3. Press OK to leave.
GOT-5100TL User’s Manual 1. Setting based on : Basic configuration 0000 2. IRQ: 03 (COM2) 3. I/O Range: 02F8-02FF (COM1) 1. Enter properties →port setting→ Advanced 2. COM Port Number→COM2 (in use) 3. Press OK to back to Device Manager and restart W indows After restarting windows, two COM4 with exclamation points disappeared. There are only COM1, COM2, and COM3.
GOT-5100TL User’s Manual The solution for removing exclamation point on Secondary IDE Channel Double click the file Lx800ide.reg where is under the folder of “GOT-5100TL-621\Driver\”. After you install this Lx800ide.reg to the registry, the exclamation point on Secondary IDE Channel will be removed.
