User Manual
Table Of Contents
- Introduction
- Parts of the WSS 1000 System
- Scanners for the WSS 1000 System
- Installing and Charging the Battery
- Assembling the WSS 1000 System
- Power
- Communicating with the Host
- Data Entry
- Removing the WWC 1000 from the Mount
- Cleaning
- Introduction
- Composants du système WSS 1000
- Lecteurs compatibles avec le WSS 100
- Mise en place et charge de la batterie
- Montage du système WSS 1000
- Alimentation
- Communication avec l’ordinateur central
- Saisie des données
- Retrait du WWC 1000 du dispositif de fixation
- Nettoyage
- Einführung
- Teile des WSS 1000-Systems
- Scanner für das WSS 1000-System
- Einsetzen und Laden des Akkus
- Montage des WSS 1000 Systems
- Strom
- Kommunikation mit dem Host
- Dateneingabe
- Herausnehmen des WWC 1000 aus der Montagevorrichtung
- Reinigung
- Introduzione
- Componenti del sistema WSS 1000
- Scanner compatibili con il WSS 1000
- Installazione e caricamento della batteria
- Assemblaggio del sistema WSS 1000
- Alimentazione
- Comunicazione con l’host
- Immissione dati
- Rimozione del WWC 1000 dal supporto
- Pulizia
- Introducción
- Partes del sistema WSS 1000
- Scanners para el sistema WSS 1000
- Instalación y carga de la batería
- Ensamblaje del sistema WSS 1000
- Alimentación
- Comunicación con el ordenador central
- Registro de datos
- Extracción del WWC 1000 del montaje
- Limpieza
- Ergonomic Recommendations
- Laser Devices
- FCC RF Exposure Guidelines
- Radio Frequency Interference Requirnments
- Radio Frequency Interference Requirements - Canada
- Marking and European Economic Area (EEA)
- Statement of Compliance
- Other Countries
- Informations réglementaires
- Recommandations ergonomiques
- Appareils lasers
- Consignes d'exposition à des RF (FCC)
- Obligations en ce qui concerne les parasites en radiofréquence
- Obligations en matière d'interférence en radiofréquence - Canada
- Marquage et zone économique européenne (ZEE)
- Regulatorische Informationen
- Ergonomische Empfehlungen
- Lasergeräte
- FCC-Richtlinien für hochfrequente Geräte
- Forderungen für Hochfrequenzstörungen
- Radio Frequency Interference Requirements - Canada
- Zeichen und der europäische Wirtschaftsraum (EWR)
- Informazioni normative
- Raccomandazioni ergonomiche
- Dispositivi laser
- Direttive FCC in materia di esposizione alle radiofrequenze
- Requisiti in materia di interferenze in radiofrequenza
- Radio Frequency Interference Requirements - Canada
- Marcatura nell'Area Economica Europea (AEE)
- Información sobre normativas
- Recomendaciones ergonómicas
- Dispositivos láser
- Pautas de exposición a RF de la FCC
- Requisitos de interferencias de las radiofrecuencias
- Radio Frequency Interference Requirements - Canada
- La marca y el Área Económica Europea (AEE)
- Service Information
Quick Reference
77
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
FCC RF Exposure Guidelines
To comply with FCC RF exposure requirements, this device must be worn
on the user’s wrist while it is in use. Other operating configurations that
have not been tested should be avoided.
Radio Frequency Interference Requirnments
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements -
Canada
This device complies with RSS 210 of Industry & Science Canada. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE