Long Range Reader User’s Manual Published: November 26, 2002 Document Control Number: MNI02H006 Matrics, Inc. 8850 Stanford Boulevard Suite 3000 Columbia, MD 21045 Tel: 410.872.0300 Fax: 410.872.0700 http://www.matrics.
Notices Copyright 2002 Matrics, Inc. All rights reserved. This document is protected by copyright with all rights reserved. No part of the document may be reproduced or transmitted by any means or in any form without prior consent in writing from Matrics, Inc. Trademarks Matrics is a trademark of Matrics, Inc. All other product names or logos mentioned herein are used for identification purposes only, and are the trademarks of their respective owners.
Contents SECTION 1. INTRODUCTION ................................................................................................1 Document Conventions..................................................................................................1 Acronyms and Abbreviations ........................................................................................1 Disclaimer ......................................................................................................................1 SECTION 2.
This page left intentionally blank. iv Long Range Reader User’s Manual 2002 Matrics, Inc.
Section 1. Introduction This Long Range Reader User’s Manual, designed for the Matrics RFID System end-user, describes the Long Range Reader (PN: RDR-090) and how to install it. Document Conventions The following conventions are used in this User’s Manual: CONVENTION DESCRIPTION 1.
Section 2. System Description Matrics develops and markets Radio Frequency Identification (RFID) solutions that are effective and affordable by offering a combination of low cost, long read range, and a very high read rate unmatched by other RFID systems. A Matrics RFID System gives you real-time, end-to-end visibility of products and assets in your factory, distribution center, retail outlet, or other facility.
Section 3. Specifications and Diagrams Reader Specification CHARACTERISTIC DESCRIPTION Name/Part Number Long Range Reader (PN: RDR-090) Operating Frequency UHF band, FCC Part 90 (909.75-921.75 MHz) Operating Channels 16 System Architecture Point-to-point and Point-to-multipoint reader network 12.5” wide (includes mounting plate) x 8.75” high (includes connectors) x 1.
Reader Diagram Mounting Plate 485 / Bus Power Connector Power/Activity LED Special Features Connector Mounting Plate +24VDC 1.2A Connector (Unit Power) Long Range Reader Part No. RDR-090 Tx4 Antenna Connectors 4 Tx3 Tx2 Tx1 Rx4 Rx3 Rx2 Rx1 12.5" wide (includes mounting plate) x 8.75" high (includes connectors) Long Range Reader User’s Manual 2002 Matrics, Inc.
Connections Diagram Functional System Connections Host/PC Bus Power 5' Patch Wiring Block Wiring Block unspec. 485 convertor RJ45 250' max. bus powered -or1,000' max. locally powered RJ45 Belden #88757 or equivalent (22 ga. CAT3) Wiring Block Local Power (optional) Long Range Reader RDR-090 CAT5 std patch 5' max. 1 3 2 4 Reader 1 mini UHF Wiring Block General Purpose Antenna Wiring Block RG-142B (25' max.
Section 4. Getting Started What’s Included? Before you proceed with your Reader installation, check that you have all of the items you need. Contact Matrics (refer to the “Contact Us” section in this User’s Manual) if any of the parts listed in this section are missing from your Reader package, or any of the items you received are damaged. NOTE: You should use ONLY those parts provided in your Reader package or specifically recommended by Matrics. Do not substitute any other cables, etc.
Section 5. Installation Follow the steps listed below (and detailed in the following sections) to install, configure, and test your Reader: 1. 2. 3. 4. 5. Mount the Reader in a location chosen for optimal surveillance. Connect antenna(s) to the Reader. Connect the Reader to your host computer. Power on the Reader. Verify that your Reader installation is operational. Mount the Reader Before mounting the Reader, you must select a location for it.
To mount the Reader: 1. Position the Reader (PN: RDR-090) at the desired mounting position on the wall, shelf, or enclosure. Make sure that there are five (5) inches of clearance on all sides of the Reader. 2. Using the pre-drilled holes at the corners of the Reader to guide you, drill four holes for mounting the reader. 3. Securely affix the Reader to the wall of shelf using the four screws that you provided.
3. To power off the Reader, unplug the power supply from the power outlet. The Power/Activity LED on the Reader should turn off, indicating that the Reader is powered off and the system is not operational. Verify the Reader Installation Reader On? After you have installed the Reader as described in this User’s Manual, test that the Reader is on by following the instructions provided above in the “Power on (and Off) the Reader” section.
Section 6. Cautions, Notes, and Approvals Matrics products are approved (or approval pending) by the appropriate regulatory agencies: • Federal Communications Commission (FCC), Part 90 Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 90 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Section 7. Warranties and Returns Limited Warranty Matrics warrants its products to the original purchaser to be free of defects in workmanship and material for a period of ninety (90) days from date of receipt. Matrics’ sole and complete responsibility under this warranty is expressly limited to repair or replacement of the defective product. Replacement products may be new or reconditioned. All products that are replaced shall become the property of Matrics.
Section 8. Troubleshooting In the event that you encounter a problem with your system, refer to the following table for possible solutions: PROBLEM POSSIBLE CAUSE SOLUTION The Reader’s Power/Activity LED doesn’t light. The AC outlet may not be working or may be controlled by a wall switch. Plug a different electrical appliance into the outlet and turn it on. If the appliance doesn’t work, plug the Reader into a different outlet. The Reader’s Power/Activity LED is on but doesn’t blink.
Section 9. Contact Us For sales, service, and technical assistance, contact Matrics at: Tel: 410.872.0300 Monday-Friday 8:30 a.m. – 5:00 p.m. EST Fax: 410.872.0700 http://www.matrics.com/ Matrics, Inc. 8850 Stanford Boulevard Suite 3000 Columbia, MD 21045 USA Long Range Reader User’s Manual 2002 Matrics, Inc.
