ATTACHMENT J – USER’S MANUAL © 2001 PCTEST Lab
S S P C S A 3 N 0 / 0 L 0 A N
S P S 3 0 0 0 S C A N / L A N © 2001 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Q u i c k R e f e r e n c e Introduction The SPS 3000 series is a family of ergonomic expansion packs for the Compaq® iPAQ® Pocket PC device that extend the capabilities of the iPAQ by adding bar code scanning and wireless functionality. Its features include: • • • • • Integrated 1D Scan Engine Integrated Spectrum24 802.
S P S 3 0 0 0 S C A N / L A N Parts of the SPS 3000 Handstrap Connecter Back View Inside View Expansion Connector Expansion Connector Top View Exit Window 2
Q u i c k R e f e r e n c e iPAQ Pocket PC Parts Used by the SPS 3000 Front View Record Button (Button 5) Power Button (Default Scan Button) Calendar (Button 1) Q Start (Button 4) Contacts (Button 2) Q Menu (Button 3) Bottom View Communications Port Reset Button Power Jack Expansion Connector 3
S P S 3 0 0 0 S C A N / L A N Installing the SPS 3000 SDK The Symbol SPS 3000 Windows CE SDK (Software Developers Kit) provides the tools necessary to create and deploy bar code scanning applications for the Compaq iPAQ Pocket PC. Note: The SDK contains the scan drivers needed to operate the SPS 3000. Download the SDK from the Software Developer Zone at this web address: http://software.symbol.com/devzone After the SDK is properly installed, reboot the iPAQ by pressing the reset button with the stylus.
Q u i c k R e f e r e n c e 5. The state of the expansion pack bettery can be found under the “External battery:” entry. Charging the SPS 3000 Battery (For SAN/LAN units only) The SPS 3000 battery is internal and cannot be removed. The battery can be charged with the expansion pack connected to an iPAQ or unconnected to an iPAQ. Charging Expansion Pack Alone Expansion Pack Power Jack S24/LAN Only 1. Insert the power plug from the AC adapter into the power jack on the expansion pack.
S P S 3 0 0 0 S C A N / L A N Note: A fully discharged battery should recharge in approximately 2.5 hours. There is no indication that the battery is charging or is fully charged. The iPAQ must be used to check the battery status. 2. Once battery is fully charged, the external power from the AC adapter can be removed. Expansion Pack Connected to an iPAQ 1.
Q u i c k R e f e r e n c e 2. The iPAQ and SPS 3000 are joined when their expansion connectors are fully engaged. (You will hear a slight click.) Expansion Connectors To remove the SPS 3000, push up on the bottom of the iPAQ to disengage the expansion connector, then slide the iPAQ off the SPS 3000 sleeves. When inserting the iPAQ and SPS 3000 into the cradle, ensure that the retractable stabilizing arms located on the inside of the cradle are extended.
S P S 3 0 0 0 S C A N / L A N SPS 3000, press the release button located on the back of the cradle. Retractable Release Note: The battery in the expansion pack will begin to charge only after the battery in the iPAQ has become fully charged. The iPAQ battery and the external battery take approximately 5 hrs. to charge altogether when both are fully discharged.
Q u i c k R e f e r e n c e Attaching the Lanyard Thread the lanyard through the handstrap connector on the back of the scanner, leaving a loop to pull the long end of the lanyard Thread the long end of the lanyard through the loop and pull. Scanning Bar Codes To scan bar codes with the SPS 3000: 1. Insert the iPAQ into the SPS 3000. 2. Press the scan trigger to launch the scanning application. 3. Press and hold the scan trigger again to turn on the laser. 4.
S P S 3 0 0 0 S C A N / L A N Maintaining the SPS 3000 For trouble-free service, follow these tips when using your SPS 3000: • • Do not scratch the exit window. The exit window of your SPS 3000 contains glass. Do not subject it to any strong impact. Protect your SPS 3000 from temperature extremes, hot or cold: - Do not leave it on the dashboard of a car on a hot day - Keep it away from heaters and other heat sources - Keep it away from freezers and other cold sources.
Q u i c k • • R e f e r e n c e Connect the equipment into an outlet on a circuit different from that which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
S P S 3 0 0 0 S C A N / L A N Scanner Labeling AVOID EXPOSURE – Laser light is emitted from this aperture.
Q u i c k R e f e r e n c e LASERPRODUKT DER KLASSE 2 RF Devices Symbol’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or authorization before using the equipment.
S P S 3 0 0 0 S C A N / L A N 14
Q u i c k R e f e r e n c e Warranty Symbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship. This warranty is provided to the original owner only and is not transferable to any third party.
Service Information Before you use the unit, it must be configured to operate in your facility’s network and run your applications. If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems Support.
Q u i c k R e f e r e n c e 17
S P S 3 0 0 0 S C A N / L A N 18
