Installation Guide

ManualsBrandsSYLVANIA ManualsWall PackSYLVANIA 61833 Luminaires UltraLED Cutoff Wall Pack

Table Of Contents

www.sylvania.com

SYLVANIA

Luminaires Installation Guide

UltraLED™ Cutoff Wall Pack

The Wall Pack luminaires are environmentally

preferable LED alternatives to traditional HID

luminaires. Ideal in place of traditional

luminaires, or as new installations, the Wall

Pack series is offered in five wattages/lumen

packages for illuminating building exteriors,

outdoor corridors, walkways, and stairwells.

For warranty coverage, please register at

www.sylvania.com/warrantyregistration.

PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION

• To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

• To avoid electric shock, serious injury, or death, be certain that all electrical power is disconnected from

the supply branch circuit conductors before installing or maintaining this fixture.

• This product must be installed and maintained in accordance with the applicable installation codes by a person

familiar with the construction and operation of the product and the hazards involved.

• Use Min 90 C supply conductors

• Make sure the supply voltage is the same as the rated luminaire voltage.

• Do not install where marked operating temperatures exceed the ignition temperature of the hazardous

atmosphere.

• Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

• Be certain electrical power is OFF before and during installation and maintenance.

• Luminaire must be connected to a wiring system with an equipment- grounding conductor.

Summary of content (11 pages)

PAGE 1
www.sylvania.com SYLVANIA Luminaires Installation Guide UltraLED™ Cutoff Wall Pack The Wall Pack luminaires are environmentally preferable LED alternatives to traditional HID luminaires. Ideal in place of traditional luminaires, or as new installations, the Wall Pack series is offered in five wattages/lumen packages for illuminating building exteriors, outdoor corridors, walkways, and stairwells. For warranty coverage, please register at www.sylvania.com/warrantyregistration.
PAGE 2
CORRELATED COLOR TEMPERATURE (CCT) SELECTION: THIS PRODUCT IS CAPABLE OF PROVIDING 3000K, 4000K OR 5000K CCT SETTING: Inside of the fixture mounted somewhere on the back plate you will find a switch showing the three CCT options available. Select the desired CCT by setting the switch to the corresponding setting. JUNCTION BOX MOUNTING: 1. Turn of Power. Take out the luminaire and loosen the screws on the cover with the aid of a screwdriver.
PAGE 3
Fig 1 -3A Fig 1-03B 3. Remove the plug on the back of the fixture (Fig 1-3A). Pull the wiring through exposed hole and secure the back housing to the junction box onto the wall (Fig 1-3B). 4. Make electrical connections per electric code. Connect black wire to LINE, White wire to NEUTRAL and Green or Green/Yellow to GROUND (Fig. 1-4). Re-attach the front cover of the fixture and re-connect the quick connect terminal (Fig1-5A). 5. Tighten the screws loosened in step 1. Installation is complete (Fig1-5B).
PAGE 4
SURFACE CONDUIT MOUNTING: 1. Turn off the power. Take out the luminaire and loosen the screws on the cover with the aid of a screwdriver. Disconnect the quick connect terminal and remove the front cover (Fig 1-1A-B). Fig. 2.2B 2. Fig. 2.2C Secure fixture to the wall. (Fig 2-2B-C). 3. Remove the appropriate threaded plug (top or sides) from the housing to allow conduit entry and attach conduit. Make electrical connections per electrical code.
PAGE 5
4. Re-attach the front cover of the fixture and re-connect the quick connect connector (Fig. 2-4A). Make sure the door gasket is properly seated around the perimeter. Close front cover and secure by tightening the two screws loosen on step 1. (Fig 2-4B). Installation is complete. Turn power on. EMERGENCY BATTERY BACKUP WIRING: If your product includes emergency battery backup please use the following electrical diagram as a reference. Fig 4A Wiring diagram for the emergency battery back-up (Fig4A).
PAGE 6
www.sylvania.com SYLVANIA Guide d’installation de luminaires Applique murale avec défilement UltraLEDMD Les appliques murales sont des alternatives DEL écologiques pour remplacer les luminaires à DHI traditionnels. Idéales pour remplacer les luminaires traditionnels ou dans les nouvelles constructions, la série d’appliques murales est offert en cinq plages de puissances/lumens pour éclairer les extérieurs d’immeubles, les couloirs extérieurs, sentiers et escaliers.
PAGE 7
MONTAGE SUR BOÎTE DE JONCTION : 1. Couper l’alimentation. Sortir le luminaire de la boîte et desserrer les vis du couvercle à l’aide d’un tournevis. Débrancher la borne de branchement rapide et retirer le couvercle avant (Fig. 1-1A-B). 2. À l’arrière du luminaire, percer les trous appropriés correspondant à la plupart des boîtes de jonction (Fig. 1-2A). Installer le joint d’étanchéité autoadhésif inclus à l’arrière du luminaire (Fig. 1-2B).
PAGE 8
Fig. 1 -3A Fig. 1-03B 3. Retirer le capuchon à l’arrière du luminaire (Fig. 1-3A). Acheminer les fils dans le trou percé et rattacher le boîtier arrière dans la boîte de jonction sur le mur (Fig. 1-3B). 4. Effectuer les connexions électriques en respectant le code électrique. Raccorder le fil noir à l’ALIMENTATION, le blanc au NEUTRE et le vert ou vert/jaune à la MISE À LA TERRE (Fig. 1-4). Rattacher le couvercle avant du luminaire et reconnecter la borne de branchement rapide (Fig1-5A).
PAGE 9
MONTAGE DU CONDUIT EN SURFACE : 1. Couper l’alimentation. Sortir le luminaire de la boîte et desserrer les vis du couvercle à l’aide d’un tournevis. Débrancher la borne de branchement rapide et retirer le couvercle avant (Fig. 1-1A-B). Fig. 2.2B Fig. 2.2C 2. Rattacher le luminaire sur le mur (Fig. 2-2B-C). 3. Retirer le capuchon fileté adéquat (sur le dessus ou les côtés) du boîtier afin de faire pénétrer le conduit et de le rattacher.
PAGE 10
6. Rattacher le couvercle avant du luminaire et reconnecter le connecteur à branchement rapide (Fig. 24A). S’assurer que le joint d’étanchéité de la porte est bien positionné autour du périmètre. Refermer le couvercle avant et rattacher en resserrant les deux vis desserrées à l’étape 1 (Fig. 2-4B). L’installation est complète. Rétablir l’alimentation.
PAGE 11
Désactiver la cellule photoélectrique -Pour le désactiver, débranchez le connecteur ci-dessous surligné d’une flèche rouge.