Instructions

Intended use
The radio-controlled switch socket is used for the connection of an
electrical consumer load. The radio-controlled remote control is used
to switch the radio-controlled switch socket on and off, thereby swit-
ching the electrical consumer-load connected to it on and off.
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or mo-
dify this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requi-
rements. All company names and product names are trademarks of
their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other de-
vices which are connected to the product.
• Do not use the product in hospitals or medical institutions. Although
the product only emits relatively weak radio signals, these may lead
to the malfunction of life-support systems. The same may also apply
to other zones.
• To supply voltage to the radio-controlled switch socket(s), only use
a proper mains socket from the public grid.
• The socket-outlet shall be installed near the equipment and shall
be easily accessible.
• The product is not a toy and does not belong in the hands of chil-
dren. Therefore, be especially careful when children are around.
Children might try to push objects through the openings of the ra-
dio-controlled switch socket’. There is danger of a life-threatening
electric shock!
• Never touch the product when your hands are wet or damp. There
is danger of a life-threatening electric shock!
• Do not connect the radio-controlled switch sockets in series.
• The radio-controlled switch socket is de-energised only when it has
been disconnected from the mains socket.
• Do not overload the radio-controlled switch socket. To this end,
please pay attention to the approved connection information in the
technical data.
• If the product casing is damaged, discontinue product usage! Do
not touch the radio-controlled switch socket or the connected device
while it is still connected to the mains voltage! First, switch off the
mains socket to which the radio-controlled switch socket is connect-
ed (switch off at the circuit breaker or the ELCB). Only then can you
remove the radio-controlled switch socket from the mains socket.
Take the product to a specialist workshop or dispose of it in an en-
vironmentally friendly way.
• Always disconnect the radio-controlled switch socket from the
mains socket if the device is not going to be used for a while.
• For safety reasons, always disconnect the radio-controlled switch
socket from the mains socket during a thunderstorm.
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RSL wireless remote control
• 3 x RSL wireless socket
• Battery CR2032
• Operating instructions
Operating instructions
RSL wireless socket switch set
Item no. 1762771
• Never use the product immediately after it has been taken from a
cold room to a warm one. The condensation that forms might dam-
age the product. There is a risk of a life-threatening electric shock!
Allow the product to reach room temperature before connecting it to
the power supply and putting it to use. This may take several hours.
• Never pour liquids over electrical devices and never place objects
lled with liquid on top of or next to them.
• Avoid operating and storing the product in close proximity to mag-
netic elds, e.g. close to machines or loudspeakers.
• Consult an expert when in doubt about operation, safety or connec-
tion of the device.
• Maintenance, modications and repairs are to be performed exclu-
sively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for
a long period of time to avoid damage through leaking. Leaking or
damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batte-
ries lying around, as there is risk, that children or pets swallow them.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge non-rechargeable batteries. There is a risk of
explosion!
Operating elements
1 Socket
2 On/off switch incl. operating state indicator
3 Battery compartment cover
4 Control lamp
5 Operating keys
6 Switch group selector switch
Inserting/replacing batteries (remote control)
1. Remove the battery compartment cover (3) on the back of the
remote control.
2. Insert a new coin cell of type CR2032 into the battery
compartment. The plus pole has to point upwards (see imprint
“+” on the coin cell). Slide the coin cell into the battery holder
until it reaches the end.
3. Close the battery compartment.
The battery needs to be replaced if the range of the
remote control is signicantly reduced or the control
lamp (4) no longer lights up when the keys are used.
Description of the keys (remote control)
• One of the four switch groups can be selected using the switch
group selector switch (6). For each of the four switch groups, three
respective channels are available. Accordingly, the remote control
features twelve channels.
• The operating keys (5) are divided into two columns:
- Left column = ON (on)
- Right column = OFF (off)
• Using the three top keys of the left column, you can activate chan-
nels 1 to 3 individually.
• Using the three top keys of the right column, you can deactivate
channels 1 to 3 individually.
• Using the key ALL ON at the bottom of the left column, you can
activate channels 1 to 3 simultaneously.
• Using the key ALL OFF at the bottom of the right column, you can
deactivate channels 1 to 3 simultaneously
The control lamp (4) lights up with every key stroke.