Instructions

Intended use
This 2-channel wireless wall switch is designed to turn on and off two
appropriate receivers (e.g. wireless power socket, wireless outdoor
socket, wireless inbuilt switch etc.). In addition, this 2-channel wireless
wall switch has a dimming function (for example, to control a wireless
plug-in dimmer, wireless inbuilt dimmer etc.).
For each control channel, a maximum of 10 receivers can be pro-
grammed.
The wireless wall switch is powered by a 12 V battery (type: 23A).
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify
this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, re, electric shock
etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European
requirements. All company names and product names are trademarks
of their respective owners. All rights reserved.
Safety instructions
Read the operating instructions carefully and espe-
cially observe the safety information. If you do not fol-
low the safety instructions and information on proper
handling in this manual, we assume no liability for any
resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Also observe the safety and operating instructions of any other
devices which are connected to the product.
• Check the product for damage before each use! If you notice any
damage, do not use the product any longer! There is a risk of a life-
threatening electric shock!
• Ensure that the insulation for the entire product is neither damaged
nor destroyed. Never disassemble the product! There are no ser-
viceable parts inside.
• Do not use this product in hospitals or medical institutions. Although
the product emits only relatively weak radio signals, these may lead
to the malfunction of life-support systems. The same may also be
the case in other areas.
• Keep the product away from strong magnetic elds occurring near
machines, electric motors or loudspeakers.
• Consult an expert when in doubt about operation, safety or
connection of the device.
• Maintenance, modications and repairs are to be performed
exclusively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for
a long period of time to avoid damage through leaking. Leaking or
damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batte-
ries lying around, as there is risk, that children or pets swallow them.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge non-rechargeable batteries. There is a risk of
explosion!
Latest operating instructions
Download the latest operating instructions via the
link www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when the-
re is a potential risk of personal injury, such as electric
shock.
An exclamation mark in a triangle indicates important ins-
tructions in this operating manual that absolutely have to
be observed.
The arrow symbol indicates specic tips and advice on
operation.
Delivery content
• RSL wireless wall switch
• Battery 12 V/23 A
• Operating instructions
Operating instructions
RSL wireless wall switch 2 channel
Item no. 1761744
Installation and Connection
The wireless wall switch is only intended for use in
dry indoor locations.
• Carefully lift the front cover of the wi-
reless wall switch (e.g. with a screw
driver) and remove it (see picture on
the right).
• Remove the mounting plate. The
mounting plate for the wireless wall
switch is xed to the electronic part
of the wireless wall switch with 4
clamps (see picture on the right).
• The mounting plate has two moun-
ting holes (see the picture on the
right). Remove the mounting plate
and mark the mounting holes on
the wall.
• Drill the holes.
• Attach the mounting plate to the wall,
using suitable mounting material.
• Attach the electronic part of the wi-
reless wall switch to the mounting
plate.
• Insert a 12V-battery (type: 23A) in
the battery compartment of the wirel-
ess wall switch, paying attention to the correct polarity.
• Attach the front plate to the wireless wall switch.