Instruction Manual

5
10.1 Attach the bracket
Important:
Adjust the screws on both sides evenly and do not overtighten.
■
Insert parts in the order shown.
10.2 Freestanding
If placed on the ground, the product should not:
■
Obstruct foot traffic.
■
Be placed in areas prone to flooding.
10.3 Wall mount
■
Use the bracket to mark where to drill.
■
Insert the included dowels.
Mount the product to the wall by fastening
the included screws to the bracket as
shown.
The solar panel should face towards the
sun. Adjust the bracket and light angle as
needed.
11 Operation
11.1 Main unit control
■
Press and hold the power / mode button to switch the power ON/OFF.
■
Short press the power / mode button to cycle through modes:
M1 → M2 → M3.
■
The indicator light will flash to indicate which mode has been selected.
11.2 Remote control
Preconditions:
a
Batteries have been inserted.
a
You are within line of sight and control range.
1. Press and hold the power / mode button on the product to switch the main power ON.
2. Press any button on the remote to control the product.
12 Light modes
Note:
"T" mode can only be selected using the remote control.
Mode Indicator
light flash
Description
M1 1x 1500 LM (first 5 hours), then 300 LM (until dawn)
Motion sensor OFF.
M2 2x 900 LM (until dawn).
Motion sensor OFF
M3 3x 300 LM (until dawn)
1500 LM (for 30 sec when motion sensor activated)
Motion sensor ON
T 4x 1500 LM (max. brightness for 2 hours), then return to previously
selected mode until dawn.
13 Troubleshooting
Problem Cause Solution
The light does not turn on. There is a nearby light
source which causes inter-
ference with the product.
Place the product in dark-
ness.
The light does not turn on. The product is switched off. Switch on using the switch
ON/OFF.
The light does not turn on. The battery power is not suf-
ficient to light the product.
Charge the rechargeable
battery.
The light stays on for short
periods.
Long periods of low sunlight
(for example cloudy weather
or in winter) will cause the
rechargeable battery to re-
charge less during the day.
Charge the rechargeable
battery.
The light stays on for short
periods.
The rechargeable battery is
old and cannot store suffi-
cient charge.
Have the rechargeable bat-
tery replaced by a qualified
professional.
14 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
■
To maximize charging efficiency, keep the solar panel(s) clean and free from debris.
■
Clean the product with a fibre-free cloth. Moisten if needed.
15 Disposal
15.1 Product
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
■
in our Conrad offices
■
at the Conrad collection points
■
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.