IN T RO D U C T I ON For the pass 8 years, SWORKz kept developing and improving their 1/8 off road nitro buggies. After the successful debut of the SWORKz S350 EVO II Limited edition (2015-2016), we continued to follow SWORKz DNA and further build on the EVO II Limited edition. Ultimately SWORKz created the S35-3 Pro Nitro Buggy.The S35-3 is a brand new SWORKz 1/8 nitro buggy. The S35-3 newly designed arms are made from a strong standard nylon material.
WARRANT Y Your SWORKz S35-3 Pro kit warranty covers workmanship and manufacturing defects of the original and unmodified parts. Warranty claims resulting from crashes, abuse, improper operation, improper mounting, improper adjustment or lack of maintenance will not be honored. Contact your local hobby shop or SWORKz distributor for all claims and questions. Claims must be well documented. All Claims are subject to expert examination approval by SWORKz.
IN D E X INSTRUCTION 2 Warranty 3 INDEX 4 Required Equipment for Operation 5 Operation Guide 6 Assembly Steps 7-37 Set-up Sheet 38 Blank Set-up Sheet 39 S350 EVO II Limited Key No.List 40 S350 EVO II Spare Part List 41-42 S350 EVO II Option Part List 43 End cover 44 This radio controlled racing car is not a toy! This high-performance R/C model is recommended for ages 14 and older.
R e q u i re d Equ ip m e nt fo r O p erat io n Radio Gear Receiver batteries Stick Type Nitro fuel We recommend that you use fuel containg 20~25% nitro. Throttle servo On/Off Switch Receiver Wheel & Trigger Type Steering servo Fuel bottle Engine Recommended Engine Starting Equipment Exhaust header ST-3 Turbo Plug ST-4 Turbo Plug Glow Plug SP-80101 EFRA2042 Starter box Tools Recommended Side cutter Long nose pliers 1.5mm Paint Curved scissors 2mm Modeling knife 2.
O p erati on G u id e Assemble front Assemble in the and rear specified order overturn Thread Locking Compound Assemble both left and right sides Grease Assemble for 2 sets Pure Silicone Oil Assemble for 4 sets Air filter oil S afet y Pre c au t io ns The SWORKz S35-3 is a high performance radio control model which needs to be operated with caution and common sense. The S35-3 Pro Kit is not intended for children under the age of 14 without adult supervision.
BAG B 1 330015 330015 x4 Pin M2.2x9.9mm 320003 330780 330014A 400002 x4 O-ring S5 4.8X1.5 116006 400002 210002A 116006 x4 Ball Bearing 8x16x5mm 330014A 116006 330015 320003 400002 2 108003 x8 M3x10mm FH/ST HEX Screw Remember to apply a light coat of grease to the o-ring, then slide it over the shaft of the out drive and seat it in the diff case. Insert the pin through the hole in the diff case and through the hole in the shaft of the out drive.
BAG C 3 330015 330768 330015 x2 Pin M2.2x9.9mm 320003 116006 400002 400002 x2 O-ring S5 4.8X1.5 330017 330017 116006 x2 Ball Bearing 8x16x5mm 210079 330015 116006 Remember to apply a very light coat of grease to the o-ring, then slide it over the shaft of the out drive and seat it in the diff case. Insert the pin through the hole in the diff case and through the hole in the shaft of the out drive.
BAG D 5 Pro Tip: Before installing the M5x4 set screw (104010), remember to clean the set screw and center driver joint (330661A) first. Then apply TLC on the set screw. 104010 x1 M5x4mm Set Screw (Flat Bottom) 106016 106016 108001 x4 M3x12mm FH/ST HEX Screw 116016 x2 Ball Bearing 5x11x4mm 2503260 (#14 #15) 330215A 330781 330661A 108001 2503261 101018 SHIM 13x16x0.
6 Pro Tip: Before installing the M5x4 set screw (104010), remember to clean the set screw and center driver joint (330661A) first. Then apply TLC on the set screw. 106016 104010 x1 M5x4mm Set Screw (Flat Bottom) 106016 108001 x4 M3x12mm FH/ST HEX Screw 330769 330781 330661A 116016 x2 Ball Bearing 5x11x4mm 108001 2503261 101018 SHIM 13x16x0.2mm 104010 x3 101018 108001 108001 101018 2503261 Note: 101018SHIM 13x16x0.2mm Please use 13x16x0.
108008 x2 M3x35mm FH/ST HEX Screw 8 101020A x2 3mm Countersunk Washers (GM) 2503260 (#24 #25) 330103 330642 2503260 (#24 #25) Use a 2mm Hex Wrench and slowly tighten the Hinge Pins. 101020A 118008 2.0mm 330103 x2 Front/Rear Lower Arm HingPin 9 2503261 Pop in the Stabilizer Guide. 104004 x2 M3x3mm Set Screw 104004 104004 115008A (2.3mm) or 115035A (2.
10 104005 x2 M3x4mm Set Screw 106013 106013 106013 x2 M2.5x8mmH ex Socket OH/TPScrew 104005 104005 11 2501097 106002 x1 M3x10mm Hex Socket OH/TP Screw 108006 108006 108003 x2 M3x10mm FH/ST HEX Screw 108006 M3x8mm FH/ST HEX Screw Note: The aluminum front upper arm holder (330772) can offer either 0° or + -1° kick-up for your front upper arm suspension. You may use the inserts 2503260-18 to get 0° kick-up or 2503260-11 to get +-1° for your front upper suspension.
BAG E1 12 Pro Tip: The S35-3 Front Upper Arm Adjust Inserts can give different steering adjustments (Ackerman). Put all inserts behind the front upper arms, you will get faster steering response. Otherwise put all inserts in front of the upper arms, you will get more stable steering response. Try to use 2503260-1 or 2503260-3 to adjust the front upper arm position.
108005 106002 x1 M3x10mm Hex Socket OH/TP Screw 330399B 108001 M3x12mm FH/ST HEX Screw x2 108005 M3x14mm FH/ST HEX Screw x2 2501097 330775 106002 108001 15 Pro Tip: The S35-3 Aluminum Rear Lower Fully Adjustable Toe-In Block (A) can use 3 types of square inserts to get 1.0/2.0/3.0 3 different toe in angles. Also plus 3 different rear lower arm kick up degrees. For the option parts SW-330795 S35-3 Aluminum Rear Lower Fully Adjustable Toe-In Block (B), you will have 0.
104004 x2 M3x3mm Set Screw 16 2503261 Pop in the Stabilizer Guide. 104004 104004 115005 (2.8mm) or 115006 (2.6mm) 17 104005 x2 M3x4mm Set Screw 106013 x2 M2.
BAG E3 18 2503264A 106002 x4 M3x10mm Hex Socket OH/TP Screw Right 106002 338009 338009 330252 2503260 Left 330118A 2503264A 330118A 330252 2503260 Screw and adjust 330118A Knuckle Pivot Ball Nut so as the pivot ball can be moved smoothly. 19 Left 104010 x2 M5x4mm Set Screw (Flat Bottom) 330124 x2 Pin M3.0x16.8mm 210046 330124 116006 x4 Ball Bearing 8x16x5mm 101018 116006 116006 101018 x1 SHIM 13x16x0.2mm 330121B Right 104010 16 Note: 101018SHIM 13x16x0.2mm Please use 13x16x0.
BAG E3 20 106020 106020 106020 340003 340003 330117A 106020 x10 M2.5x5mm Hex Socket OH/TP Screw 330117A BAG E2 21 103001 x2 M3 Nut Lock 106007 116004 101021 106007 330776 117003 610019 101021 101021 x2 M3x8xT1mm 117003 330773 117003 x4 Flange Ball Bearing 3x6x2.
BAG E2 22 108003 x2 M3x10mm FH/ST HEX Screw 108003 116004 x2 Ball Bearing 6x10x3mm 101019 x1 SHIM 6.0x10.0x0.2mm 101019 116004 330113 BAG E3 23 104010 x2 M5x4mm Set Screw (Flat Bottom) Note: 101018SHIM 13x16x0.2mm Please use 13x16x0.2mm shims to adjust the gap between the wheel hub and wheel knuckles. Standard suggestion is 1pc shim on the outside between 8x16x5mm ball bearing and knuckle. 210046 330124 x2 Pin M3.0x16.
24 2503260 103001 2503260 Pro Tip: The base set up is always by using 2-3mm inserts on the rear of Hub Carriers Hinge Pins. The wheel base length should be around 327-328mm. 2503260 103001 330782 103001 x2 M3 Nut Lock 330782 330782 x2 Rear Hub Carriers Hing Pin with Nut 2503260 25 2501121C 330123A x2 Rear Upper Sus. Arm Turnbuckles 330125 2503270-02 330125 330123A 13.
103001 x4 M3 Nut Lock 26 103001 106003 106006 106006 x2 M3x20mm Hex Soket OH/TP Screw 106003 x2 M3x16mm Hex Socket OH/TP Screw 106006 103001 103001 103001 27 106010 x4 M3x6mm Hex Socket OH/TP Screw 2501115 106010 2501115 20 106010
28 2501097 106008 2501097 103001 103001 106008 2501097 103001 106008 103001 x4 M3 Nut Lock 2501097 106008 x4 M3x12mm Hex Soket OH/TP Screw 29 106006 106006 x2 M3x20mm Hex Soket OH/TP Screw 106005 x2 M3x15mm Hex Soket OH/TP Screw 106005 21
BAG F 30 104004 330104 108006 106007 x4 M3x12mm Hex Socket OH/TP Screw(HT) 108006 108006 330090 104004 x2 M3x3mm Set Screw 106007 104004 106007 108006 x4 M3x8mm FH/ST HEX Screw 210043 116009 116009 330647 330104 210043 210043 116009 x2 Ball Bearing M5x8x2.
BAG F 32 106010 330766 2501123 106010 x8 M3x6mm Hex Socket OH/TP Screw 2501123 106010 33 108003 x2 M3x10mm FH/ST HEX Screw 108010 x2 M4x10mm FH/ST HEX Screw 108012 x4 M4x16mm FH/ST HEX Screw 2501097 108012 108012 108010 108003 23
34 108003 x3 M3x10mm FH/ST HEX Screw 2501529 108011 x4 M4x12mm FH/ST HEX Screw 108003 330767A 108011 108003 35 2501529 108012 x4 M4x16mm FH/ST HEX Screw 103001 106006 x1 M3x20mm Hex Socket OH/TP Screw 106006 103001 x1 M3 Nut Lock 330663A 108012 108011 24 108012
BAG G 36 Right 2503270 (#3) 330126A x2 Steering Turnbuckle 23.95mm 330777 330126A 330777 2503270 (#3) S35-3/E Steering curve ball end additional manual 37 20.8mm We suggest when you are using the back holes for the S35-3 and S353/E steering ackerman plate, try using the curve ball plastic end on the outside steering linkage ball. This way the steering will improve and the response will be smoother, there will not be any over angle. 2503270 (#3) Right 20.8mm 2501121C 21.
38 106008 106008 106003 106003 106008 x4 M3x12mm Hex Soket OH/TP Screw Servos are not included in the kit. 106005 x4 M3x15mm Hex Soket OH/TP Screw 2503262 2503262 2503262 39 103001 x2 M3 Nut Lock 106002 Receiver and switch are not included in the kit. The switch is not included in the kit. 106002 x2 M3x10mm Hex Soket OH/TP Screw Laps transponder is not included in the kit.
40 108006 108006 108006 x4 M3x8mm FH/ST HEX Screw 41 104004 x1 M3x3mm Set Screw Li-ion Size:18500 106001 x3 M3x8mm Hex Socket OH/TP Screw Battery is not included in the kit.
42 108006 x6 M3x8mm FH/ST HEX Screw 108006 106007 x1 M3x12mm Hex Socket OH/TP Screw(HT) 43 108006 108006 106007 2501122B 330134 103001 x1 M3 Nut Lock 2501121C 330155 x1 Steering Servo Turnbuckle (M3x30mm) 330134 103001 330155 2501121C 17.
BAG M1 44 106007 x1 M3x12mm Hex Socket OH/TP Screw(HT) 106007 SW-330423A Aluminum Settring Bellcrank Upper (A 2H ) Assembly Note 108006 108006 x1 M3x8mm FH/ST HEX Screw Position A Position B 103001 x1 M3 Nut Lock If servo saver arms are not included use this: Position A: Standard steering response location. Use of a 2.5mm longer servo saver arm is required. If servo saver arms are included use this: 103001 Position A: Standard steering response location. Use of the included 2.
45 108003 x2 M3x10mm FH/ST HEX Screw 108003 108003 BAG I 47 105005 101013 105005 x4 M3x12mm Cap Screw 105005 101013 101013 x4 3mm Spring Washer 330008A 330100A 30 330100A
48 105001 x1 M3x8mm Cap Screw 115003A 330006 101012 x1 M3x6xT0.6mm 330137 101015 x5 M5x8xT0.4mm 105001 330006 116010 116010 101012 116010 x2 Ball Bearing 5x10x4mm 101015 101015 115003A 115003A 330006 49 105007A x4 M4x8mm I-Head Screw 105007A 50 104011 x2 M4x4mm Set Screw (Flat Bottom) 104011 108013 x1 M4x8mm FH/ST HEX Screw 330140A 330140A Pipeset is not included in the kit.
BAG J 51 210018 106007 2503260 104004 104004 104004 x6 M3x3mm Set Screw 106020 210018 330157A 106020 2501125C 330156A 104004 210018 106007 x1 M3x12mm Hex Socket OH/TP Screw(HT) 2501112B 104004 210018 x1 Throttle Rod 50mm 330157A 52 106020 x3 M2.
BAG J 54 Front 330636(S) Front 330634(S) 330635(L) x2 S350 New BBS System +5.5mm Shock Shaft ( L) 103004 Rear 330635(L) Rear 330633(L) 330562(F) 330563(R) 400020 330636(S) x2 S350 New BBS System +1.3mm Shock Shaft ( S) 210058 101011 210058 210058 210058 103004 x4 M2.5mm Nut Lock 330557 2501121C 210058 x4 Shock Seal Washer 3.5X7X1.0mm Front 400010(S) 210058 x8 Shock Seal Washer 3.6X7X2.5mm 55 101011 x4 M2.6x6xT0.
BAG J 105013A x4 M3x25mm Cap Screw 57 330138B 105013 330138B 101010A 101010A 101010A 105013A 105013A 58 103003A 103003A x4 Flange M3 Nut Lock 106005 x4 M3x15mm Hex Socket OH/TP Screw 106005 106005 103003A 106005 106005 34
59 Using air filter oil (Not included) 108006 x1 M3x8mm FH/ST HEX Screw 540003 610004 106002 x1 M3x10mm Hex Socket OH/TP Screw 103003 x1 Flange M3 Nut Lock 610004 2501126A 108006 2501126A 103003 106002 60 410038 35
BAG E 61 105005 220014BK 220014BK 105005 x2 M3x12mm Cap Screw 220014BK 62 330122A x4 Wheel Nut 330122A 330122A 63 Use body scissors to cut along the body lines.
64 Use water/washing solution to clean body. Apply window masks as shown. 250048 Paint body.
SET-UP SHEET Track Conditions Size: Traction: Surface: Diff. Oil Front: # 5000 Center: # 7000 Rear: # 3000 Name: Micha Widmaier Date: 7.-9.07.2017 Track: ABC Reding Clutch Clutch shoes: Sworkz Spring: 1,0 1 Front Roll Center mm Camber angle Upper Left = Right mm mm Lower Left = Right Sway bar Al(11g) Brass(25g) Brass(35g) -1 0 +1 Wheel Hub Note: 95 mm F 0 mm Front Shock System 600 Oil: Pistons: 8x1.
SET-UP SHEET Track Conditions Size: Traction: Surface: Diff.
Pa r ts No. L i s t Part No. 210002A 210033B 210079 2503263-01 2503263-02 2501097 2503264A 2503270-1 2503270-2 2503270-3 2503261 2501115 2502040-02 220014BK 2501116-01 2501121C 2501122B 2501123 2501124 2501125B 2501126A 2501529 2503262 2503260 Part Name Q`ty in Use ltem No.
Spare Par t List Pa Parrts ts No. No. Lis L istt Part No.
Spare Pa r t L is t Item No.
Op ti on P a r t L is t Item No. Part Name Item No.
Production No.