User Guide
Table Of Contents
- Radicom Research. Inc.
- Designer’s Guide for the
- Introduction of RW8300E-a-PR (USB-device) Universal Adapter Products
- Features
- Approvals
- RW8300E-a-PR Universal Adapter Application Summary
- The RW8300E supports LAN. USB and WiFi interfaces. The RW8300E-NL supports WiFi and USB but without LAN.
- RW8300E works in bridge mode and connects to router by a RJ45 cable. RW8300E is under the same domain with router. RW8300E-NL works in WISP mode and plays as gateway. RW8300E-NL will connect to RW8300E through WiFi. and will get an IP address “192.168...
- ※WISP: Wireless Internet Service Provider
- ※NIC: Network Interface Controller
- WARNING: Please ensure the AP router is not 192.168.137.xxx domain for sub-net otherwise the device will get 192.168.136.xxx IP address.
- Physical Description
- Standard RJ45 10/100 BASE-T Port
- RW8300E-a-PR Quick Start Method
- Connection Process of RW8300E-a-PR
- Various Connection Processes of RW8300E-a-PR
- Reset RW8300E-a-PR (USB-Device) to the Default
- 1. Connect your device and RW8300E-NL with USB cable to power on RW8300E-NL. and wait one minute for startup.
- 2. Insert a pin into the RESET hole. long-press RESET button over 5 seconds. until LED flash within 1/8 seconds. Then release RESET button and wait 2 minutes. RW8300E-NL will change back to factory default setting. Once system reboots and LED glowing ...
- 1. Plug in USB adapter to power on RW8300E. and waiting 1 minute to start system up.
- 2. Insert a pin into the RESET hole (near the LAN port). press and hold the RESET button for 2-5 seconds. RW8300E will reboot.
- 1. Connect to web page of RW8300E and RW8300E-NL
- 2. Setup Static IP address
- 3. Setup to obtain an IP address automatically (DHCP)
- 4. Upgrade firmware In this section. we’ll show you how to upgrade firmware. Also. how to check firmware version and md5sum.
- Important Regulatory Compliance and User Information
- FCC RF Radiation Exposure Statement
- IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements. the antenna used on this transmitter must be installed to provide a separation of at least 20 cm from all persons and must not be co-located or operating in conjunction with ...
- FCC Interference Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
- (1) This device may not cause harmful interference
- (2) This device must accept any interference received. including interference
- that may cause undesired operation.
- This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates and radiates radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a partic...
- ● Reorient or relocate the receiving antenna.
- ● Increase the separation between the equipment and receiver.
- ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- ● Consult the dealer or an experienced radio/TV technician for assistance.
- IC (Industry Canada) Statement:
- “This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference. and (2) this device must accept any interference. including interference that ...
- Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de license. L’exploitation est autorisee aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage. et (2) l’utilisateur de l’ap...
- Europe – The Radio Equipment Directive (RED) Compliance Statement: Hereby. Radicom Research Inc. declares that this equipment complies with the essential requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. The Rad...
- CE Declaration of Conformity
- For the following equipment:
- is herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the
- Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/CE). For the evaluation regarding this Directive. the following
- standards were applied:
- This equipment is marked with the and can be used throughout the European community.
- France – 2.4GHz for Metropolitan France:
- In all Metropolitan departments. wireless LAN frequencies can be used under the following conditions. either for public or private use:
- Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band
- Limited Warranty
- Warranty Coverage and Duration
- What this Warranty does NOT Cover:
- How to Receive Warranty Service:
- General Provision
- Contacting Radicom Research
- http://www.radi.com/
RW8300E-a-PR (USB) Designer’s Guide (RRD2Z50-20200130001) 13
RJ45 Ethernet Cable Description
The following table shows the RJ45 connector pin assignments for Ethernet cable.
PHY data rate is 100Mbps.
Contact
10/100 Base-T Signal
1 TD+ (Transmit Data)
2 TD- (Transmit Data)
3 RD+ (Receive Data)
4 Not used
5 Not used
6 RD- (Receive Data)
7 Not Used
8 Not Used
Ethernet Port Connector Pin Definitions
Standard RJ45 10/100 BASE-T Port
A RJ45 connector is used for Ethernet twisted pair links. The RJ45 connector has 8-pins.
and may also be referred to as an 8-pin modular connector. A male RJ45 plug is
mounted on each end of the twisted pair cable. A female RJ45 jack or receptacle is
integrated into the Ethernet hub or NIC.
Ethernet Connector (J1)
CAT.5e Ethernet cable
RJ-45 Plug
(8 pin)