Model：S-1073F 7’’ Full HD Waveform LCD Monitor User Manual Ver：C Please read this User Manual throughout before using.
Preface 1. All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2. All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners. 3.
Maintenance Warning 1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places. 2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio signals. The power 1. Please use the power adapter provided or recommended by the manufacturer in order to avoid damage. 2. For a third party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit. 3.
Packing List ： This product offers the standard package and luxury package for option, respectively including Standard package: 1. User manual 2. Warranty card 3. Articulating arm trestle 4. Sun hood 5. D-tap to Pole-tap DC cable with lock 6. S-7006(U/F/D)/ S-7000(A/S) Luxury package: 1. User manual 2. Warranty card 3. Sun hood 4. Articulating arm trestle 5. D-tap to Pole-tap DC cable with lock 6. HDMI cable 7. BNC cable 8. S-7006(U/F/D)/ S-7000(A/S) 9. Power cord 10. Power adaptor 11.
Accessories introduction 1. Sun hood Take out the sun hood from the flannel bag, see pic1; Push out the sun hood as pic2, unfold as pic3; Fold the two bottom parts inward as pic3, with the internal magnets attached and fixed as pic4; Install the sun hood on the monitor, see as pic5. ⑴ ⑵ ⑶ ⑷ Pic.1 Pic. 3 Pic. 2 Pic. 4 Pic.
2. Battery plate Take off the rubber cover in the rear panel of S-1073F; connect the power pins on the tail of the battery plate to the power socket of S-1073F, fix with four screws. Mounting the battery to the plate can power the monitor. 3. Arm Trestle As shown in the picture above which marked with 1, 2, 3 of the arm trestle can be 360°rotated. User can rotate to any position according to their needs.
Operation Instructions ⑴ Rubber buttons SOURCE: Signal selection button User definable function keys F1 F4 User can set F1 F4 keys to corresponding function for quick operation according to their needs. For example User can set F1 to “Focus Assistant”, and press F1 to directly switch the focus assistant parameter, the sequence is “Red→Blue→Off”. Quick function keys support multi definition, for details please refer to “4.Function key settings” in the “MENU” section.
⑸ DC 12V: Round head DC power supply interface (Outer: Negative, Inner: Positive) ⑹ Battery mount connector ⑺ GPI: GPI control socket ⑻ Video Signal Interface ⑼ ⑽ SDI-IN1: 3G/HD/SD SDI input (BNC connector) SDI-IN2: 3G/HD/SD SDI input (BNC connector) SDI-OUT: SDI output (BNC connector) When the input is SDI, loop output the signal connected to SDI-IN When the input is HDMI, output HDMI converted to SDI signal Note: when the input is HDMI, SDI-OUT does not support SD-SDI signal HDMI-IN: HDMI signal input,
⑹. Histogram User can set function Keys F1～F4 as “Histogram” to turn on or off this function. ⑺. Vector User can set function Keys F1～F4 or GPI pins as “Vector” to turn on or off this function. The relevant parameters like Vector position, Vector color and Vector blending, etc. can be changed under “Vector” submenu. . Waveform User can set function Keys F1 F4 or GPI pins as “Waveform” to turn on or off this function.
～ User can set function Keys F1 F4 as “Freeze Frame” to turn on or off this function R/G/B/Mono R/G/B/Mono is to display only the blue/red/green primary signal or the luminance signal only so as to monitor the image noise. User can set function Keys F1 F4 as “R/G/B/Mono” to turn on or off this function. False Color The false color is used to aid in the setting of camera exposure. Under false color mode, there’s a color chart on the bottom of screen for reference.
4. Revolve “MENU” to change the selected item’s parameter, press “MENU” to apply and save the settings. 5. Revolve “MENU” to select “Exit”, press “MENU” to quit submenu. Select “Exit & Status” under the Main Menu and press to quit Main Menu. Notice: ＊ The items in gray can not be set up. ＊ If there is no operation under the setted time, the menu will automatically save settings and quit. ＊ If the key inhabit function is turned on, except key inhibit function, all other items are in grey.
3. Color Temp To select different color temperature or setup user-defined color parameters * Only “Color Temp” is set to “User”, the Red/Blue/Green Gain or Red/Blue/Green Bias can be adjusted. 4.
When connecting the GPI pin with ground, the setted function will be turned on, and goes out when disconnecting. Example 1: Under “GPI ” submenu, set “GPI control” to “On”, set “2 Pin” to “Red Tally”, when the pin 2 of the extenal GPI control unit is connected with ground, the Tally light will display on the front panel which will flashes in red around every second. When disconnected, the monitor will not display tally light information.
Aspect ratio: 4:3 Safety Area: 85% Center Marker: On Fit Marker: Off Aspect ratio: 4:3 Safety Area: 85% Center Marker: Off Fit Marker: On 8. Audio *1 When “Bar Frame” is set to “Off”, only the audio meter will be displayed. When “Bar Frame” is set to “On”, frame and real-time audio value will be displayed. *2 Select Channel Under HDMI signal, channel1-2 can be selected. Under SDI signal, channel 1-2, 1-8 and 1-16 can be selected.
Channel1 ～2 Channel1 ～8 ～ Channel1 16 9. Vector 10. Waveform *1: Only the “WFM Single Line” is set to “ON”, the “WFM Line Count” can be adjusted.
11. Display 12. System *1 Source Scan When set to “Yes”, after turn on the monitor, the signal will be inspected and follow the sequence of “SDI→HDMI→CVBS” For example: if channel is selected to SDI, SDI-IN has no input, and HDMI has input. When turn on the monitor, after automatic inspection, SDI has no recognized signal, and HDMI has recognized signal, then the input signal will be HDMI. When set to “No”, update model will not be supported. *2 Logo When powered on, the screen will display SWIT logo. *3.
when upgrading ）； ⑸ After upgraded, the monitor will automatically reboot. 13. OSD 14. Key Inhibit When the “Key inhibit” is set to “on”, there is no response when all the buttons except ” MENU” is pressed, the sreen will be displayed as ” Key Inhibit”. User can set “Key inhibit” to off under the “Key inhibit” submenu, restore the function of all keys.
Specification LCD Performance Size Display area Resolution Color Aspect ratio Brightness Contrast Viewing angle 7 inch 151.2×94.5 mm 1920×RGB×1200 8 bit 16:9⁄4:3 400 cd⁄ 1000:1 Horizontal / Vertical: 160°⁄160° ㎡ Input/Output Input Output HDMI×1 BNC×2 BNC×1 USB×1 HDMI input 3G/HD/SD-SDI input CVBS input 3G/HD/SD-SDI loop through output/ HDMI converted to SDI output SDI/HDMI audio output BNC×1 3.
Trouble-shooting symptom No display Image or color abnormal Possible causes Solution The power is not turned on Please check if the power is connected, and then press ”POWER” button to turn on the monitor Unstable power voltage Reconnect to power supply BNC or HDMI cable loose contact or not correctly connected Check and correctly connect the BNC or HDMI cable The attached battery is no power Change battery Using DIY power supply but the polarity is reversed Refer to the provided power supply,
