Back-to-Wall Carrier System INSTALLATION INSTRUCTIONS Swiss Madison Residential Concealed In-Wall Toilet Tank for Back-to-Wall Toilet SM-WC324 @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect carrier to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS Parts for Reference: 5 6 7 19 2 4 8 3 20 21 22 1 9 10 23 11 24 12 14 15 16 17 25 13 18 31 26 27 28 29 30 Flush Actuator not included 32 33 — 2 —
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 1. Fasten Mounts (if fastening to studs) · Adjust clips then fasten carrier to studs or wall framing. · Ensure frame is flush and level before fastening. 1a. 1b.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 1. Fasten Mounts (if fastening to wall) · Adjust clips then fasten carrier to studs or wall framing. · Ensure frame is flush and level before fastening.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 2. Cut Pipe · Measure and cut pipe according to your toilet. · Make sure to measure the sub floor and finished floor measurements before cutting to have the correct center. · Once pipe is cut, remove any burrs. 39 ³⁄8” 1 2 L(max. 5 ¹5⁄16”) L=X-H 3 H X 0 3. Attach Pipe · Apply grease before sliding on pipe. · Install pipe then put on dust cap to prevent debris from entering the pipe.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 4. Remove Plate · Remove plate and attach to water connection. 1 1 1 2 2 2 3 1 5. Attach Water Connection · Hold the shut-off valve stationary while tightening water connection. · Install locking nut as shown.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 6. Flush Debris · After attaching water connection to shut-off valve, undo the other side of the hose. · Turn on valve to flush any debris before installing the actuator. 1 2 3 7. Reconnect Water Supply · After flushing debris, reconnect the water supply hose. a. c. 2 1 b. d.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 8. Reinstall Plate · Reinstall actuator and cover plate. · Ensure roughing box is secure to keep debris from entering the tank. *Click* 2 2 1 1 *Click* 9. Trim Roughing Box · After wall materials are installed, trim roughing box. max. ¹⁄8” max.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS Toilet Installation 1. Fit Pipe · Install pipe and make sure it is thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the finished wall. · Remove from wall and install pipe in the back of the toilet and make sure it is thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the back of the bowl. 2. Cut Pipe · Measure the distance between both marked lines on pipe.
Swiss Madison ® ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) 19 Stults Road Dayton, NJ 08810 www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
