Freestanding Vanity ® INSTALLATION INSTRUCTIONS @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect product to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · Floor must be level prior to installation of vanity. · All dimensions are nominal! Be sure to measure your vanity prior to installation. · The step-by-step guidelines in the installation instructions are a general reference.
FREESTANDING VANITY Parts for Reference: 1. Base panel 2. Left side panel 3. Right side panel 4. Front cross bar 5. Side leg connecting boards (2) 6. Front leg connecting boards (2) 7. Rear top bar 8. Rear bottom bar 9. Left door 10. Right door 11. Cross beam (2) A. Cam bolt B. Cam lock C. Wooden dowel D. Allen key E. Screws F. Washer G. Screws H. Wrench I. Screws J. Screws for handles K. Handles (2) L. Foam pad M.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 2. Prepare Frame & Side Panels • Connect a cross beam (11) to the front cross bar (4) via the cam bolt (A) installed in the front cross bar (4). Secure into place with a cam lock (B). Repeat with the remaining cross beam (11). • Complete the frame by attaching the rear top bar (7) to the cross beams (11) using 2 screws (E). Secure into place by tightening the screws (E) using an allen key (D). • Screw 5 cam bolts(A) into the left panel (2).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 4. Attach Base • Place the base panel (1) onto the cabinet frame as shown. • Insert 6 screws (E) into the base panel as shown. Using an allen key (D), secure the base into place. D E 1 5. Assemble Leg Frame • Connect bracket (BC410) to the left and right side of the side leg connecting board (5). • Use 6 screws (G) and secure into place as shown. Be careful to leave about 2 mm of clearance between the screw head and bracket (BC410).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 6. Install Leg Frame • Insert 8 wooden dowels (C) into the leg frame as shown. • Attach the leg frame to the base panel (1) by sliding the wooden dowels into the base. • Insert 10 screws (I) into the leg frame as shown. Using an allen key (D), tighten each screw fully to secure the frame into place. D I 1 C 7. Install Legs • Take a leg (LC22B2) and remove the cover from the peg as shown. Repeat for all 4 legs.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 8. Prepare Cabinet for Installation • Insert corner brace (BC67) into the corner of the cabinet as shown. Tighten all screws to secure into place. Repeat for the last 3 corners using an additional 3 corner braces (BC67). • Using the levelers on the bottom of the legs, adjust the height as needed. Use a level to verify that the adjusted cabinet height is level on all sides. • Optional: Remove the backing of a foam pad (L).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 9. Secure Vanity to Wall • Select installation method from below. Please note that mounting hardware is not supplied with this vanity. Option 1: Securing to Drywall · Position cabinet against wall in desired location. · Using a pencil, make a mark on the wall through the holes in the rear top bar (7). · Move cabinet away from the wall. Create a pilot hole in each mark on the wall, then insert a plastic anchor.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 11. Attach Doors • Install 2 hinges (HS26A) to both the left door (9) and the right door (10) using 2 screws (G) per hinge. • Use an additional 2 screws per hinge to attach the left door (9) and right door (10) to the cabinet. If the doors do not align properly, adjust the hinges according to the diagrams below. Once adjustments have been completed, secure the hinges using 2 screws (G) each. • Install the handles (K) to the doors using the handle screws (J).
® well made forever ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) www.swissmadison.com Swiss Madison products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
