Freestanding Vanity INSTALLATION INSTRUCTIONS @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect product to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · Floor must be level prior to installation of vanity. · All dimensions are nominal! Be sure to measure your vanity prior to installation. · The step-by-step guidelines in the installation instructions are a general reference.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS Parts for Reference: 1. Left side panel 2. Right side panel 3. Rear top bar 4. Front top bar 5. Rear bottom bar 6. Front top bar 7. BottomPanel 8. Left door 9. Right door 10. Left drawer, left wall 11. Left drawer, right wall 12. Left drawer, back wall 13. Drawer divider back wall 14. Right drawer, left wall 15. Right drawer, right wall 16. Right drawer, back wall 17. Drawer bases (2) 18. Drawer divider base 19. Top drawer panel (above doors) A.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 1. Attach Drawer Tracks · Screw 9 cam bolts (B) into the left side panel (1). Repeat for the right side panel (2). · Attached left drawer track (D) into left side panel (1) by using 5 screws 14mm (E). Repeat for the right side panel (2). E 5 E 5 B B 9 9 E 5 2 E 5 1 D D 2. Assemble Base · With the right side panel (2) lying down flat, use 2 wooden dowels (C) to attached the bottom panel (7).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 3. Assemble Top Drawer Frame · Insert cam bolts (B) into the inner drawer side walls (10) (11) (14) (15). Note: use one cam bolt for each wall. · Insert 6 cam bolts (B) into the top drawer panel (19). · Attach the left (12)and right (16) back walls to the side panels using 4 wooden dowels (C). · Attach the left and right drawer frames together using the drawer divider (13) and 2 additional wooden dowels (C).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 4. Complete Top Drawer Assembly · With the drawer frame assembled, insert the drawer bases (17) and the divider base (18) into the existing tracks. · Attach the drawer panel (19) onto the frame and secure all cam bolts (B) using 6 cam locks (A). · Stand the cabinet base upright and attach the fully assembled drawer. Tighten the drawer to the track using two screws (E).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 5. Install Doors · Install 2 hinges (L) to both the left door (8) and the right door (9) using 2 screws (E) per hinge. · Use an additional 2 screws per hinge to attach the left door (8) and right door (9) to the cabinet. If the door does not align properly, adjust the hinges according to the diagrams below. Once adjustments have been completed, secure the hinges using 2 screws (G) each.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 6. Attach Legs · Connect legs to the bottom panel (7) using 4 square support plates (N) and 16 (E). N 4 E 7 7. Secure Vanity to Wall · Attach 2 corner brackets (O) to the rear top bar (3) using 16 screws (E). · Mark desired mounting location on wall and ensure placement is level. · Select installation option 1 or 2. O 2 Option 1: Securing to Drywall · Position cabinet against wall in desired location.
FREESTANDING VANITY INSTALLATION INSTRUCTIONS 8. Vanity Top Installation · Install faucet and drain according to manufacturer’s installation instructions. Do not overtighten, this may cause the sink to crack. · Set the vanity top on top of the vanity base, checking the location of the p-trap and drain. · Remove vanity top from vanity base. Apply a thin bead of silicone around the vanity base and set the vanity top carefully in place. · Remove excess silicone with a wet cloth.
well made forever ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
