PREDATOR TALON WHERC10224C swisherinc.com OWNER’S MANUAL PREDATOR WHERC10224 STARTING SERIAL #: L116-336001 MODEL NO. WHERC10224C WHERC10224 IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. COMMERCIAL PRO 24” WALK BEHIND 12V ROUGH CUT Operation Service and Adjustment Repair Parts ade I The SWISHER ACQUISITION INC.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
Thank you for choosing Swisher’s 24” Walk Behind Rough Cut. Before operating your Walk Behind, please read, understand and follow all of the safety precautions and other instructions explained in this manual. As with all power equipment, lawn mowers can be potentially dangerous if not properly used. SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.
• • • • • • • • • • • Turn off the blade when not mowing. Before leaving the machine, turn off the blade and stop the engine. Watch for traffic when operating near or crossing roadways. Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary. Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.
OPERATING YOUR NEW WALK BEHIND The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any mower produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
STARTING THE ENGINE See engine manufacturer’s recommendations for the type and amount of oil and fuel used. Engine must be level to accurately check and fill oil. Do not overfill. • Make sure unit is level, blade is disengaged, and transaxle in “NEUTRAL” • Check spark plug wire, oil level, and fuel level. • Check all electrical connections for build-up of debris. • Move throttle control to “FAST”, or “CHOKE” if choke is needed.
TRANSPORTING • Remove the key from ignition switch. • Shut off fuel at the engine. • Secure in place while unit is being transported. • Unit should be left in low gear to avoid any slight rolling. SUGGESTED PRACTICES • Always operate engine at full throttle when cutting to assure the best cutting performance and proper discharge of material. • If grass is wet, allow it to dry. Wet grass clumps will collect on the bottom of the deck. • Go slow when cutting dense areas.
SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher.
ASSEMBLY DETAIL WHERC10224C MODEL SHOWN WITH CASTERS When ordering replacement parts *USE PAINT CODE: TK=BLACK BATTERY NOT INCLUDED: REQUIRES A 12V LAWN AND GARDEN BATTERY WITH A 235 MIN CCA. U1 GROUP FOR CORRECT FIT. Tip: Valve stems should be turned to avoid contact with caster yoke.
ENGINE & PULLEY ASSEMBLY Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description Nut - Nyloc 5/16-18 Bolt - Serr Flange, 5/16-18 X 1 Nut - Serr Flange 5/16-18 Bolt - 5/16-24 X 1 HCF GR5 ZY Bolt - Serr Flange, 5/16-18 X 1 1/2 Spacer - Engine Pulley Weldment - Belt Retention Belt - Transmission, 35" Washer - 1 X 1 1/2 Key Stock - 1/4 X 1 Engine Pulley- 4.25"OD,1 1/4 ID Washer - .531IDX1 1/2OD Bolt - HCF, 7/16-20 X 1 1/2 Washer - Belleville 7/16 X 1 1/4 Pulley - Engine, 2.
REAR COVER ASSEMBLY Item # 1 2 3 4 5 Description Nut - Serr Flange 5/16-18 Plate - Cover, Back Arm - Anti Reverse Spacer Bolt - Serr Flange, 5/16-18 X 3/4 Part # NB170 10679* 10680* B99S NB596 HANDLE BAR & LEVER ASSEMBLY Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 NOT SHOWN Description Keys - Key Switch, Set of Two Harness - Wiring, When ordering replacement parts *USE PAINT CODE: TK=BLACK Part # KSK 20988 11 Description Knob - T Bolt - TCS 1/4-20 X 1/2 Cable - Throttle Weldment - Hand
BLADE DRIVER ASSEMBLY Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Description Nut - Jam 3/4-16 Washer - Belleville .760 X 1.5 X .098 Pulley - Blade, 5.5" Spacer - 3/4 ID X 1 Washer - 3/4 ID X 1 1/4 OD Bearing - Blade Shaft - Blade 6", Long Shoulder Nut - Serr Flange 5/16-18 Housing - Blade Bearing Bolt - Serr Flange, 5/16-18 X 3/4 Washer - Flat 3/4 ID X 1 3/4 OD Nut - Lock, Two Way 3/8-24 Plate - Blade Mount Blade - G6 Gator 24" Bolt - 3/8-24 X 1 1/4 HCC GR5 ZY Washer - SP Bellville .413 X.945 X.
DECK & CASTER ASSEMBLY FOR MODEL WHERC10224C Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Description Deck - Weldment Bolt - 1/4-20 X 3/4 Clip - Blade Engagement Cable Nut - Nyloc 1/4-20 Nut - Serr Flange 5/16-18 Weldment - WB Skid Bolt - Serr Flange, 5/16-18 X 3/4 Washer - 5/8 ID X 1 OD Tire/Wheel - 8 X 3 Nut - Lock Jam, 5/8-11 2 Way Bolt - 5/8-11 X 5 Weldment - Caster, Txt Blk Washer - 13/16 X 1 1/4 X 1/8 Bearing Weldment - Brush Guard Housing Washer - Flat Nut - Jam, Nyloc 3/4-16 Cap PAGE 12 Pa
TRANSAXLE ASSEMBLY Item # 1 2 3 4 5 6 7 Description Wheel - Asy Right; WB24 4.
WIRING CONFIGURATION Wiring Harness PN 20988 BELT CONFIGURATION 2410 TRANSAXLE PULLEY 690 – TRANSAXLE BELT TOP ENGINE PULLEY CONFIGURATION B27 – TRANSAXLE IDLER PULLEY 2411 – TOP ENGINE PULLEY BB105 – LOWER ENGINE PULLEY 20655 – BLADE ENGAGEMENT BELT T30V – V-BELT PULLEY BOTTOM ENGINE PULLEY CONFIGURATION B527 – BLADE IDLER PULLEY 20651 – BLADE PULLEY 15
swisherinc.com OWNER’S MANUAL MODEL NO. COMMERCIAL PRO 24” WALK BEHIND 12V ROUGH CUT Each cutter has its own model number. Each engine has its own model number. The model number for the cutter will be found on the right hand side of the drive belt housing. The model number for the engine will be found on the engine block. All cutter parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer.
