User Manual

ManualsBrandsSwing-N-Slide ManualsSportspower Swing SetsTimberview Wooden Swing Set with Two Slides and Monkey Bars

ASSEMBLY INSTRUCTIONS

6ZLQJ16OLGH%DUEHUU\'ULYH-DQHVYLOOH:LVFRQVLQ

9LVLWRXUZHEVLWHDWZZZVZLQJQVOLGHFRPRUFDOOXVDW

6ZLQJ16OLGH,QF 3ULQWHGLQ86$ /$

IMPORTANT!!

PLEASE READ BEFORE BEGINNING ASSEMBLY!!

Please make sure all lumber, hardware and accessory parts are accounted for.

If you are missing anything, please DO NOT RETURN to the store where purchased.

Please call our Customer Service Department at the number below.

LDR 2-25-2018

WS 8356

Summary of content (64 pages)

PAGE 1
WS 8356 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS 6ZLQJ16OLGH %DUEHUU\ 'ULYH -DQHVYLOOH :LVFRQVLQ 9LVLW RXU ZHE VLWH DW ZZZ VZLQJ Q VOLGH FRP RU FDOO XV DW 6ZLQJ 1 6OLGH ,QF 3ULQWHG LQ 86$ LDR 2-25-2018 /$
PAGE 2
5CHGV[ %JGEMNKUV HQT 5YKPIÄ0Ä5NKFG 2NC[ 5GVU CPF #EEGUUQTKGU 1DUGTXKPI VJG HQNNQYKPI UVCVGUOGPVU CPF YCTPKPIU TGFWEGU VJG NKMGNKJQQF QH UGTKQWU QT HCVCN KPLWT[ 6JKU RNC[UGV JCU DGGP FGUKIPGF HQT WUG D[ C OCZKOWO QH VJKTVGGP QEEWRCPVU CV QPG VKOG JCXKPI C EQODKPGF YGKIJV QH RQWPFU 6JKU RNC[UGV KU KPVGPFGF HQT WUG D[ EJKNFTGP HTQO VQ [GCTU QH CIG 1PÄUKVG CFWNV UWRGTXKUKQP HQT EJKNFTGP QH CNN CIGU KU TGEQOOGPFGF +PUVTWEV EJKNFTGP PQV VQ YCNM ENQUG VQ KP HTQPV QH
PAGE 3
2.#;5'6 /#+06'0#0%' %QUOGVKE FGHGEVU VJCV FQ PQV CHHGEV VJG UVTWEVWTCN KPVGITKV[ QH VJG RTQFWEV QT PCVWTCN FGHGEVU QH YQQF UWEJ CU YCTRKPI URNKVVKPI EJGEMKPI VYKUVKPI UJTKPMCIG UYGNNKPI QT CP[ QVJGT RJ[UKECN RTQRGTVKGU QH YQQF VJCV FQ PQV RTGUGPV C UCHGV[ JC\CTF CTG PQV EQXGTGF D[ QWT YCTTCPV[ 6Q JGNR OKPKOK\G VJGUG PCVWTCN FGHGEVU YG TGEQOOGPF CRRN[KPI C UGCNGT QT UVCKP GXGT[ VYQ QT VJTGG [GCTU QT OQTG QHVGP CU VJG ENKOCVG FKEVCVGU 2QYGT YCUJKPI UCPFKPI QT QVJGT RTGRCTCVQT[ OGVJQFU UJQWNF DG
PAGE 4
2.#;)4170& 574(#%+0) /#6'4+#.5 5'%6+10 1( 6*' %1057/'4 241&7%6 5#('6; %1//+55+105 176&114 *1/' 2.
PAGE 5
PLAYSET SAFETY ZONE 16'-4 1/8" 6'-0" 14'-0" 6'-0" 28'-7 3/16" 16'-5 15/16" 28'-0" 6'-0" 14'-0" 6'-0" 6'-0" 27'-1" MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
PAGE 6
TOOLS REQUIRED DRILL 1/2” & 7/16’’ SOCKETS & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SCREWDRIVER PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 1/8” DRILL BIT HELPFUL ASSEMBLY INFORMATION Your playset consists of several boxes or modules. It is important to ensure all lumber, accessories and hardware is accounted for. The following pages list the contents of each box. Use these pages to take an inventory of all parts.
PAGE 7
TOWER MODULE SA 6081 /SA6022 BOARD LIST (4) [PF 6164] 3’’ x 3’’ x 94’’ (2) [PF 6063] 3/4’’ x 3-3/8’’ x 59-5/8’’ A-FRAME BASE (1) [PF 6020] 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT (3) [PF 6006] 3/4’’ x 3-3/8’’ x 44-1/2’’ (1) [PF 6019] 2-11/16’’ x 5-3/8’’ x 93’’ SWING BEAM (2) [PF 6050] 3/4’’ x 3-3/8’’ x 43-1/2’’ (2) [PF 6004] 3/4’’ x 3-3/8’’ x 42’’ (1) [PF 6018] 2-11/16’’ x 3’’ x 62’’ A-FRAME SUPPORT (5) [PF 6005] 3/4’’ x 3-3/8’’ x 42’’ (2) [PF 6017] 1-3/8’’ x 3-3/8’’ x 83’’ A-FRAME LEGS (2) [PF 6003]
PAGE 8
TOWER MODULE SA 6081 /SA6022 COMPONENTS CONT.
PAGE 9
TOWER MODULE SA 6081 /SA6022 HARDWARE 1/4”-20 x 1-1/4” Hex Bolt (x12) 5/16”-18 x 6-1/2” Carriage Bolt (x12) 5/16”-18 x 6” Carriage Bolt (x3) 5/16”-18 x 2-1/2” Hex Bolt (x2) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 4” Hex Bolt (x5) 5/16”-18 x 6” Hex Bolt (x2) 5/16”-18 x 7” Hex Bolt (x1) 5/16-18 T-Nut (x28) Small 1/4’’ Loc Washer (x12) 5/16” Washer (x36) 1/4’’ Washer (x16) 5/16’’ Loc Washer (x12) #8 x 1/2” Pan Screw (x2) 1/4’’ T-Nut (x12) #12 x 3/4” Pan Screw (
PAGE 10
TERRACE MODULE SA 6031 BOARD LIST (1) [PF 6061] 1-1/2’’ x 1-1/2’’ x 40’’ (2) [PF 6028] 1-3/8’’ x 3’’ x 79’’ (2) [PF 6026] 1’’ x 3-3/8’’ x 42’’ (3) [PF 6005] 3/4’’ x 3-3/8’’ x 42’’ (4) [PF 6025] 3/4’’ x 3-3/8’’ x 29-1/4’’ (3) [PF 6024] 3/4’’ x 3-3/8’’ x 27-3/4’’ (2) [PF 6150] 3/4’’ x 3-3/8’’ x 24-3/4’’ (1) [PF 6023] 3/4’’ x 3-3/8’’ x 22-1/2’’ (1) [PF 6022] 3/4’’ x 3-3/8’’ x 19-1/2’’ (10) [PF 6021] 5/8’’ x 5-3/8’’ x 30-3/4’’ (6) [PF 6135] 3/4’’ x 5-3/8’’ x 26-1/4’’ TERRACE HARDWARE 5/16’’ Loc Washer (x4) 1-
PAGE 11
WOOD ROOF PICNIC TABLE MODULE SA6035 SA6037 BOARD LIST BOARD LIST (18) [PF 6055] 1/2’’ x 5’’ x 47-1/2’’ SHINGLE (1) [PF 6040] 1’’ x 5-3/8’’ x 41-1/2’’ BENCH (2) [PF 6061] 1-1/2’’ x 1-1/2’’ x 40’’ (2) [PF 6133] 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE (2) [PF 6038] 3/4’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG (2) [PF 6037] 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT (2) [PF 6039] 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT ROOF HARDWARE TABLE HARDWARE 1-5/8” Deck Screw (x96) 2-1/2” Deck Screw (x10) 2” Deck Screw
PAGE 12
MONKEY BAR SA6036 BOARD LIST (1) [PF 6041] 1-3/8’’ x 3-3/8’’ x 29-1/4’’ (2) [PF 6042] 1-3/8’’ x 3-3/8’’ x 32’’ (2) [PF 6043] 1-3/8’’ x 3-3/8’’ x 60’’ (2) [PF 6045] 1-3/8’’ x 3-3/8’’ x 79-7/8’’ (1) [PF 6044] 1’’ x 3-3/8’’ x 58’’ MONKEY BAR HARDWARE 5/16”-18 x 3-1/2” Hex Bolt (x2) 5/16”-18 x 3” Hex Bolt (x2) 2-1/2” Pan Head Screw (x18) 5/16”-18 x 2” Hex Bolt (x2) 5/16”-18 x 1-1/2” Hex Bolt (x6) 2-1/2” Deck Screw (x12) 5/16” Loc Nut (x4) 1-1/4” Pan Head Screw (x14) 5/16-18 T-Nut (x8) Small Anchor It (x
PAGE 13
FORT ENCLOSURE SA6036 BOARD LIST (7) [PF 6407] 5/8’’ x 5-3/8’’ x 29-5/8’’ (1) [PF 6408] 3/4’’ x 5-3/8’’ x 41-1/2’’ (1) [PF 6410] 3/4’’ x 5-3/8’’ x 41-1/2’’ ARCHED (1) [PF 6409] 3/4’’ x 3-3/8’’ x 41-1/2’’ (2) [PF 6414] 5/8’’ x 3-3/8’’ x 29-5/8’’ (2) [PF 6415] 1-3/8’’ x 1-3/8’’ x 3-3/8’’ (4) [PF 6416] 1-3/8’’ x 1-3/8’’ x 5-3/8’’ FORT ENCLOSURE HARDWARE 2-1/2” Deck Screw (12) 30mm Deck Screw (x40) 13
PAGE 14
STEP 1 6’’ 47-1/2’’ Flush 6’’ (3) 2-1/2’’ Screws /8’’ 9-5 5 x /8’’ 3-3 SE x ’ A ’ 3/4 ME B 3 6 RA 60 A-F PF (3) 2-1/2’’ Screws 1’’ 010 6 PF ’’ -3/8 3 x /2’’ 7-1 4 x T-Nut Small PF 6164 3’’ x 3’’ x 94’’ PF 6164 3’’ x 3’’ x 94’’ (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 59-1/4’’ PF /8’’ 3-3 x ’’ 3/4 6 0 60 /2’’ 4-1 4 x FRAME A (2) 2-1/2’’ Screws 1-1/2’’ BOTH SIDES Hint!! Use parts from your Tower Box. 2-1/2” Deck Screw (x14) 1.
PAGE 15
STEP 2 6’’ (3) 2-1/2’’ Screws Flush ’’ 5/8 59x /8’’ 3-3 SE x BA /4’’ 3 3 AME 6 0 R 6 A-F PF 6’’ PF 6164 3’’ x 3’’ x 94’’ (3) 2-1/2’’ Screws 0 601 F P /8’’ 3-3 x 1’’ PF 6164 3’’ x 3’’ x 94’’ 47-1/2’’ /2’’ 7-1 4 x T-Nut Small (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 59-1/4’’ PF /8’’ 3-3 x /4’’ 63 0 0 6 ’’ 1/2 4 x4 (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME B 1-1/2’’ BOTH SIDES 2-1/2” Deck Screw (x14) 1.
PAGE 16
STEP 3 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws Flush PF 600 53 /4’’ x PF 600 53 /4’’ x 3-3 /8’’ x 3-3 /8’’ x 42’ ’ (2) 2-1/2’’ Screws 42’ ’ PF 600 43 /4’’ x 3-3 /8’’ x 42’ ’ Flush (2) 2-1/2’’ Screws PF 600 43 /4’’ x 3-3 /8’’ x 42’ ’ (3) 2-1/2’’ Screws PF 600 53 /4’’ x FRAME A 2-1/2” Deck Screw (x13) 1. Attach support boards to Frame A as shown.
PAGE 17
STEP 4 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME B (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x13) 1. Attach Frame A to Frame B as shown.
PAGE 18
STEP 5 PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (6) 1-3/4’’ Screws (2) 2-1/2’’ Screws (6) 1-3/4’’ Screws PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ 16-1/2’’ PF 6011 1’’ x 3-3/8’’ x 47-1/2’’ 16-1/2’’ PF 6011 1’’ x 3-3/8’’ x 47-1/2’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (2) 2-1/2’’ Screws 1-3/4” Deck Screw (x12) TOP VIEW 2-1/2” Deck Screw (x4) 1. Install Deck Boards as shown.
PAGE 19
STEP 6 (7) PF 6008 3/4’’ x 5-3/8’’ x 42’’ (6) 1-3/4’’ Screws per board 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 3/8’’.
PAGE 20
STEP 7 Flush (3) 1-3/4’’ Screw per joint (4) 3’’ Screw NOTE: PRE-DRILLED HOLES (2) PF 6149 1-3/8’’ x 3-3/8’’ x 15-1/2’’ DECK SUPPORT Flush NOTE: Insert Hardware From Outside 5 600 PF ’’ 3/4 ’’ x -3/8 3 x ’ 42’ (3) 2-1/2’’ Screws 31’’ (3) 2-1/2’’ Screws 1-3/4” Deck Screw (x6) 2-1/2” Deck Screw (x6) 3” Deck Screw (x4) 1. Install Deck Supports as shown.
PAGE 21
STEP 8 Check to make sure structure is square (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer T-Nut Small PF 602 61 ’’ x 3-3 /8’’ x4 2’’ 47-1/4’’ Flush Hint!! Use parts from your Terrace Box. 2-1/2” Deck Screw (x4) 1. Install Deck Support Board as shown.
PAGE 22
STEP 9 Check to make sure structure is square PF ’’ x 3/4 5 600 x /8’’ 3-3 ’ 42’ PF 6028 1-3/8’’ x 3’’ x 79’’ PF 6028 1-3/8’’ x 3’’ x 79’’ (3) 2’’ Screws Flush ’’ 3/4 5 0 60 PF Flush (3) 2’’ Screws ’’ x -3/8 3 x ’ 42’ (3) 2’’ Screws FRAME C 2” Deck Screw (x12) 1. Assemble Frame C as shown.
PAGE 23
STEP 10 Check to make sure structure is square ’’ 61 2 0 6 PF ’’ x -3/8 3 x ’ 42’ 5/16-18 X 2’’ Hex Head Bolt 47-1/4’’ 5/16’’Loc-Washer 5/16’’ Washer (2) 2’’ Screws T-Nut Small 2” Deck Screw (x4) 1. Install Deck Support Board as shown.
PAGE 24
STEP 11 Flush Check to make sure structure is square (2) 2-1/2’’ Screws PF 604 11 -3/8 ’’ x 3-3 /8’’ x2 9-1 /4’’ Flush 3/4 ’’ x PF 60 3-3 /8’’ 25 x2 9-1 /4’’ (2) 2-1/2’’ Screws Flush (2) 2-1/2’’ Screws 3/4 ’’ x PF 60 3-3 /8’’ 24 x2 7-3 /4’’ Flush FRAME C (2) 2-1/2’’ Screws PF 602 43 /4’’ x 3-3 /8’’ x 273/4 ’’ Hint!! Use parts from your Monkey Bars Box. 2-1/2” Deck Screw (x8) 1. Install Frame Support Boards as shown.
PAGE 25
STEP 12 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws 79’’ (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME C 2-1/2” Deck Screw (x10) 1. Attach Frame C to Tower as shown.
PAGE 26
STEP 13 (1) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ (1) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ 10-5/8’’ 10-5/8’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ TOP VIEW 1-3/4” Deck Screw (x10) 1. Install Deck Boards as shown.
PAGE 27
STEP 14 (6) PF 6135 3/4’’ x 5-3/8’’ x 26-1/4’’ All Boards Flush (6) 1-3/4’’ Screws per board Note: Holes 1-7/8’’ From Edge on This Side 1-3/4” Deck Screw (x36) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 7/16’’.
PAGE 28
STEP 15 PF 6005 3/4’’ x 3-3/8’’ x 42’’ (6) 2-1/2’’ Screws 53-7/8’’ 2-1/2” Deck Screw (x6) 1. Attach Gap Filler Boards as shown.
PAGE 29
STEP 16 PF 6022 3/4’’ x 3-3/8’’ x 19-1/2’’ (3) 2’’ Screws PF 6023 3/4’’ x 3-3/8’’ x 22-1/2’’ (3) 2’’ Screws 50-5/8’’ 2” Deck Screw (x6) 1. Install Barrier Support Boards as shown.
PAGE 30
STEP 17 (6) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ (4) 30mm Screws per board 1-7/8’’ Panel Bracket (8) 3/4’’ Pan Screws #12 x 3/4” Pan Screw (x8) INSIDE VIEW 30mm Deck Screw (x24) 1. Install Barrier Boards as shown. No gaps between boards.
PAGE 31
STEP 18 PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ (3) 2-1/2’’ Screws Flush (2) 2-1/2’’ Screws PF 6005 3/4’’ x 3-3/8’’ x 42’’ PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ Flush (2) 2-1/2’’ Screws 62-5/8’’ 2-1/2” Deck Screw (x10) 1. Install Barrier Support Boards as shown.
PAGE 32
STEP 19 1’’ 3-1/8’’ 3-1/8’’ 1’’ 1-5/8’’ PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 1/2’’ GAP PRE-DRILL (4) 1/8’’ HOLES 1/2’’ GAP PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 17-3/8’’ (4) 30mm Screws per board PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ 4-7/8’’ (10) 3/4’’ Screws per Window Frame PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 2-13/16’’ x2 30mm Deck Screw (x8) 2-13/16’’ x2 Hint!! Use parts from your Tower Box.
PAGE 33
STEP 20 (2) 30mm Screws per board 1’’ (2) 30mm Screws per board (2) 30mm Screws per board (2) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws 30mm Deck Screw (x24) #12 x 3/4” Pan Screw (x8) 1. Install Window Panels.
PAGE 34
STEP 21 PF 6020 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT TOP OF BEAM SUPPORT 84’’ FROM BOTTOM OF POST Loc Nut 5/16’’ Washer Wood Loc-Washer 5/16-18 X 6’’ Carriage Bolt 1. Install Swing beam support as shown.
PAGE 35
STEP 22 CENTER PF 6019 2-11/16’’x5-3/8’’x93’’ Swing Beam TOWER THIS SIDE T TH OWE IS R SID E = DRILL HERE (6 PLACES) MARK HOLE LOCATION 30mm Deck Screw (4 per Clamp) 5/16”-18 x 6-1/2” Carriage Bolt BOTTOM VIEW SIDE VIEW 5/16” Clamp, Beam 2-1 PF 1/1 6 601 Sw ’’x5-3 9 ing /8 Be ’’x93 am ’’ HD Swing Hanger NOTE HOLE LOCATIONS NOTE HOLE LOCATIONS 5/16” Washer A-FRAME THIS SIDE 5/16” Loc Nut 1. Locate the PF 6019 Swing Beam in your kit. 2.
PAGE 36
STEP 23 PF 6018 2-11/16’’x3’’x62’’ A-Frame SB Support 5/16”-18 x 7” Hex Head Bolt (1) 3’’ Screws (1) 3’’ Screws 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 6017 1-3/8’’x3-3/8’’x83’’ A-Frame 5/16”-18 x 2-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Washer (2) 2-1/2’’ Screws 5/16”-18 x 4” Hex Head Bolt (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 5/16-18 T-Nut Small PF 6016 1-3/8’’x3-3/8’’x58’’ A-Frame Support 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut S
PAGE 37
STEP 24 (2) Swing Beam Bracket 5/16”-18 x 3-1/2” Hex Head Bolt x2 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/2” Hex Head Bolt 5/16” Washer x2 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
PAGE 38
STEP 25 Beam Brace 5/16”-18 x 3 1/4” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 1. Install Swing Beam Brace as shown.
PAGE 39
STEP 26 5/16”-18 x 6” Carriage Bolt 5/16”-18 x 8-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16” Wood Loc Washer 5/16” Washer 5/16” Loc Nut 1. Install Swing Beam as shown.
PAGE 40
STEP 27 (4) 30mm Screws per board (6) PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 30mm Deck Screw (x24) 1. Install Barrier Boards as shown. NOTE: Standard gap between deck boards is 1/2’’.
PAGE 41
STEP 28 (1) 3’’ Deck Screws 1-5/8’’ 1-5/8’’ 13-1/2’’ PF Check to make sure structure is square 60 62 PF ’’ 21 6 60 ’’ 3/8 x3 ’’ 1/2 2 x4 E AM R F AF O RO PF 6058 5/8’’ x 3-3/8’’ x 30’’ (4) 30mm Deck Screws 1’’ x3 -3 /8’ ’x 42 -1 /2’ ’R OO FA -F RA ME x2 3/4’’ CENTERED PF 6060 5/8’’ x 5-3/8’’ x 13’’ SUN (2) 30mm Screws x2 30mm Deck Screw (x12) 3” Deck Screw (x2) 1. Assemble Roof A-Frames as shown.
PAGE 42
STEP 29 (4) 30mm Screws (6) 30mm Screws (1) PF 6056 5/8’’ x 2’’ x 10’’ (2) PF 6059 5/8’’ x 2’’ x 7’’ x2 Note: Place screws through A-Frame and into end of PF 6053 CENTERED Note: PF 6053 Rests on Top of PF 6056 (2) 2-1/2’’ Screws /2’’ 1 43 PF 6053 1-3/8’’ x 3-3/8’’ x 43-1/2’’ SIDE VIEW (2) 2-1/2’’ Screws Note: Place screws through A-Frame and into end of PF 6053 /2’’ 1 43 30mm Deck Screw (x20) 2-1/2” Deck Screw (x4) 1. Assemble the Roof frame as shown.
PAGE 43
(5) PF 6055 1/2’’ x 5’’ x 47-1/2’’ SHINGLE Per Side STEP 30 1’’ OVERHANG BOTH SIDES (4) 1-5/8’’ Deck Screws per board ’’ 21 /2’’ 1 45 (1) 1-5/8’’ Deck Screw per board ’’ 21 /2’’ 1 45 (2) PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ (4) PF 6055 1/2’’ x 5’’ x 47-1/2’’ SHINGLE Per Side (2) PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ 21 ’’ 21 ’’ UNDERSIDE VIEW (5) 1-5/8’’ Deck Screws per board 1-5/8” Deck Screw (x90) Hint!! Use parts from your Wood Roof Box. 1. Assemble Roof as shown.
PAGE 44
STEP 31 3/4’’ Offset Each Side (3) 1-5/8’’ Screws Side View (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws NOTE: Secure Roof from the INSIDE (3) 1-5/8’’ Screws 1-5/8” Deck Screw (x12) 1. Attach Roof Frame to Tower as shown. NOTE: Secure roof from inside the tower.
PAGE 45
STEP 32 /2’’ x 43-1 ’’ 8 / 3 ’’ x 3 50 3/4 PF 60 (4) 2’’ Screws (4) 2’’ Screws 3-1/2’’ -3/8’’ x 4 3 x ’’ /4 3 PF 6050 2” Deck Screw (x8) 1. Attach Roof Side Support Boards as shown.
PAGE 46
STEP 33 ALIGN SCREWS WITH PRE DRILLS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD (6) PF 6389 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARDS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD 2” Deck Screw (x32) 1. Align and install rock wall boards to the image above.
PAGE 47
STEP 34 Panel Bracket (4) 3/4’’ Pan Screw (3) 2-1/2’’ Screws Under Deck View 2-1/2” Deck Screw (x6) 1. Attach Rock Wall as shown.
PAGE 48
STEP 35 (2) 1/4’’ T-Nuts (2) 1-1/4’’ Hex Head Bolts (2) 1/4’’ Flat Washer Per Rock (2) 1/4’’ Loc-Washer Per Rock 1. Attach Climbing Rocks as shown.
PAGE 49
STEP 36 Flush (2) ‘L’ Brackets (3) 1-1/4’’ Pan Head Screws per L Bracket (2) PF 6043 1-3/8’’ x 3-3/8’’ x 60’’ 49-1/4’’ (5) Short Monkey Bar Rungs 38-1/4’’ (2) 2-1/2’’ Pan Head Screws per rung 27-1/4’’ 16-1/4’’ 5-1/4’’ 19’’ T-Nut Small 5/16’’ Washer 5/16’’Loc-Washer 5/16-18 X 1-1/2’’ Hex Head Bolt (2) Triangle Brackets 2-1/2” Pan Head Screw (x10) Hint!! Use parts from your Monkey Bar Box. PLACE NO BOLTS HERE 1. Assemble Horizontal Ladder as shown.
PAGE 50
(2) PF 6045 1-3/8’’ x 3-3/8’’ x 79-7/8’’ STEP 37 (3) Monkey Bar Rungs 36-1/4’’ (2) 2-1/2’’ Pan Head Screws per rung 24-1/2’’ 12-3/4’’ Flush 22’’ PF 6044 1’’ x 3-3/8’’ x 58’’ 5/16’’ Washer 5/16’’Loc-Washer T-Nut Small (4) 2-1/2’’ Screws (2) PF 6042 1-3/8’’ x 3-3/8’’ x 32’’ 5/16-18 X 3-1/2’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 5/16-18 X 2’’ Hex Head Bolt T-Nut Small 2-1/2” Pan Head Screw (x6) 2-1/2” Deck Screw (x4) 1. Assemble vertical ladder as shown.
PAGE 51
STEP 38 5/16-18 X 3’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer T-Nut Small 5/16-18 X 1-1/2’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer T-Nut Small Flush (3) 1-1/4’’ Pan Head Screws per L Bracket 1-1/4” Pan Head Screw (x6) 1. Assemble and attach Monkey Bar Assembly as shown.
PAGE 52
STEP 39 (2) PF 6039 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT 3’’ (2) PF 6037 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT (4) 1-1/4’’ Screws 2-3/4’’ 3’’ 11-1/4’’ (4) 1-1/4’’ Screws (4) 2’’ Screws (2) PF 6133 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE OUTSIDE FACE TO OUTSIDE FACE, BOTH SIDES (4) 2’’ Screws 2-3/4’’ 6-7/8’’ OUTSIDE FACE TO OUTSIDE FACE, BOTH SIDES 6-7/8’’ (2) PF 6038 1’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG (2) 2’’ Screws 36’ ’ (2) 2’’ Screws PF 6040 1’’ x 5-3/8’’ x 41-1/2’’ BENCH Check
PAGE 53
STEP 40 (4) 1-5/8’’ Screws per board PF 6410 3/4’’ x 5-3/8’’ x 41-1/2’’ ARCHED PF 6024 3/4’’ x 3-3/8’’ x 27-3/4’’ Flush PF 6408 3/4’’ x 5-3/8’’ x 41-1/2’’ (4) 2-1/2’’ Screws Flush Flush 31’’ Flush PF 6409 3/4’’ x 3-3/8’’ x 41-1/2’’ (4) 1-3/4’’ Screws per board HINT: Use boards from Fort Enclosure 1-3/4” Deck Screw (x8) 1-5/8” Deck Screw (x4) 1. Attach Fort Enclosure Support Boards to Tower as shown.
PAGE 54
STEP 41 Flush Flush (4) 30mm Screws per board 1-3/4’’ GAP TO UPRIGHT BOTH SIDES (4) 30mm Screws per board 1’’ GAP 1’’ GAP (5) PF 6407 5/8’’ x 5-3/8’’ x 29-5/8’’ (4) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ NO GAPS BETWEEN BOARDS (2) PF 6414 5/8’’ x 3-3/8’’ x 29-5/8’’ NO GAPS BETWEEN BOARDS Under Deck View HINT: Use boards from Fort Enclosure Under Deck View 30mm Deck Screw (x40) 1. Install Enclosure Boards as shown. 2. Install Barrier Boards as shown.
PAGE 55
STEP 42 (2) PF 6180 5/8’’ x 3-3/8’’ x 10-1/2’’ (6) 30mm Deck Screws Underdeck View Grade (2) 30mm Deck Screws 2” PF 6009 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake 30mm Deck Screw (x8) 1” Truss Screw (x3) 1. Attach Slide Support Boards and Slide as shown.
PAGE 56
STEP 43 PF 6452 1-3/8’’ x 3-3/8’’ x 22’’ (4) 1-3/4’’ Screws From Behind Deck Support Flush to Support Flush to Upright Underdeck View Grade (2) 30mm Deck Screws 2” PF 5999 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake 30mm Deck Screw (x2) 1-3/4” Deck Screw (x4) 1” Truss Screw (x4) 1. Attach Slide Support Boards and Slide as shown.
PAGE 57
STEP 44 1/4” Washer 1/4’’ x 1-3/4” Pan Screw 11” 1/2” Pan Screw (x2) 1-3/4” Pan Screw (x2) 1. Attach Safety Handle and I.D. Tag as shown.
PAGE 58
STEP 45 FIG. A HD Ring-Trap Combo Assembly 1. Attach Ring-Trap Chain to Swing Hanger as shown in (Fig. A). 2. Tighten Quick Link to secure chains to Swing Hangers as shown in (Fig. A).
PAGE 59
STEP 46 FIG. A 83 H 8" Minimum HD Swing Seats 1. Attach Chain to Swing Hanger as shown in (Fig. A). 2. Tighten Quick Link to secure chains to Swing Hangers as shown in (Fig. A). NOTE: Once installed, there must be a minimum 8’’ clearance between the bottom of the swings and the surfacing.
PAGE 60
STEP 47 5/16” Washer Fold up Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 3ODFH VZLQJ VHW LQ ¿QDO ORFDWLRQ DQG PRXQW $QFKRU ,W V DW ORFDWLRQV FLUFOHG DERYH 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
PAGE 61
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at: www.OnlineWarranty.net Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty SURYLGHV FRQ¿GHQFH DQG GHPRQVWUDWHV RXU FRPPLWPHQW WR providing quality residential playground products.
PAGE 62
PAGE 63
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration %HQH¿WV RI UHJLVWHULQJ RQOLQH Ŷ Quick & simple from home or mobile Ŷ Record your purchase in our system Ŷ Initiate product warranty Ŷ Improved customer support Ŷ 1RWL¿FDWLRQ RI QHZ SURGXFW LQIRUPDWLRQ Register your product online at www.OnlineWarranty.
PAGE 64
Got Questions? We’ve got answers! Call our Customer Support Representatives 1-800-888-1232 Available Monday - Friday, 7am - 5pm (CST) Weekend support available April through July Technical support from experienced Swing-N-Slide customer service representatives who have actually built a swing set themselves. © Swing-N-Slide Inc.