User Manual

ManualsBrandsSwing-N-Slide ManualsSportspower Swing SetsWillows Peak Deluxe Wooden Swing Set

ASSEMBLY INSTRUCTIONS

6ZLQJ16OLGH%DUEHUU\'ULYH-DQHVYLOOH:LVFRQVLQ

9LVLWRXUZHEVLWHDWZZZVZLQJQVOLGHFRPRUFDOOXVDW

6ZLQJ16OLGH,QF 3ULQWHGLQ86$ /$

WS 8349

IMPORTANT!!

PLEASE READ BEFORE BEGINNING ASSEMBLY!!

Please make sure all lumber, hardware and accessory parts are accounted for.

If you are missing anything, please DO NOT RETURN to the store where purchased.

Please call our Customer Service Department at the number below.

LDR 2-25-2018

WS 8350

Summary of content (60 pages)

PAGE 1
WS 8349 WS 8350 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS 6ZLQJ16OLGH %DUEHUU\ 'ULYH -DQHVYLOOH :LVFRQVLQ 9LVLW RXU ZHE VLWH DW ZZZ VZLQJ Q VOLGH FRP RU FDOO XV DW 6ZLQJ 1 6OLGH ,QF 3ULQWHG LQ 86$ LDR 2-25-2018 /$
PAGE 2
5CHGV[ %JGEMNKUV HQT 5YKPIÄ0Ä5NKFG 2NC[ 5GVU CPF #EEGUUQTKGU 1DUGTXKPI VJG HQNNQYKPI UVCVGUOGPVU CPF YCTPKPIU TGFWEGU VJG NKMGNKJQQF QH UGTKQWU QT HCVCN KPLWT[ 6JKU RNC[UGV JCU DGGP FGUKIPGF HQT WUG D[ C OCZKOWO QH VJKTVGGP QEEWRCPVU CV QPG VKOG JCXKPI C EQODKPGF YGKIJV QH RQWPFU 6JKU RNC[UGV KU KPVGPFGF HQT WUG D[ EJKNFTGP HTQO VQ [GCTU QH CIG 1PÄUKVG CFWNV UWRGTXKUKQP HQT EJKNFTGP QH CNN CIGU KU TGEQOOGPFGF +PUVTWEV EJKNFTGP PQV VQ YCNM ENQUG VQ KP HTQPV QH
PAGE 3
2.#;5'6 /#+06'0#0%' %QUOGVKE FGHGEVU VJCV FQ PQV CHHGEV VJG UVTWEVWTCN KPVGITKV[ QH VJG RTQFWEV QT PCVWTCN FGHGEVU QH YQQF UWEJ CU YCTRKPI URNKVVKPI EJGEMKPI VYKUVKPI UJTKPMCIG UYGNNKPI QT CP[ QVJGT RJ[UKECN RTQRGTVKGU QH YQQF VJCV FQ PQV RTGUGPV C UCHGV[ JC\CTF CTG PQV EQXGTGF D[ QWT YCTTCPV[ 6Q JGNR OKPKOK\G VJGUG PCVWTCN FGHGEVU YG TGEQOOGPF CRRN[KPI C UGCNGT QT UVCKP GXGT[ VYQ QT VJTGG [GCTU QT OQTG QHVGP CU VJG ENKOCVG FKEVCVGU 2QYGT YCUJKPI UCPFKPI QT QVJGT RTGRCTCVQT[ OGVJQFU UJQWNF DG
PAGE 4
2.#;)4170& 574(#%+0) /#6'4+#.5 5'%6+10 1( 6*' %1057/'4 241&7%6 5#('6; %1//+55+105 176&114 *1/' 2.
PAGE 5
PLAYEST SAFETY ZONE 6'-0" 14'-0" 16'-2 9/16" 6'-0" 6'-0" 28'-0" 28'-8" 13'-8 1/16" 14'-0" 6'-0" 6'-0" 28'-2 3/16" MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
PAGE 6
TOOLS REQUIRED DRILL 1/2” & 7/16’’ SOCKETS & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SCREWDRIVER PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 1/8” DRILL BIT HELPFUL ASSEMBLY INFORMATION Your playset consists of several boxes or modules. It is important to ensure all lumber, accessories and hardware is accounted for. The following pages list the contents of each box. Use these pages to take an inventory of all parts.
PAGE 7
TOWER MODULE SA6051 / SA6022 BOARD LIST (4) [PF 6164] 3’’ x 3’’ x 94’’ (2) [PF 6063] 3/4’’ x 3-3/8’’ x 59-5/8’’ A-FRAME BASE (1) [PF 6020] 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT (3) [PF 6006] 3/4’’ x 3-3/8’’ x 44-1/2’’ (1) [PF 6019] 2-11/16’’ x 5-3/8’’ x 89-1/2’’ SWING BEAM (2) [PF 6050] 3/4’’ x 3-3/8’’ x 43-1/2’’ (2) [PF 6004] 3/4’’ x 3-3/8’’ x 42’’ (1) [PF 6018] 2-11/16’’ x 3’’ x 62’’ A-FRAME SUPPORT (5) [PF 6005] 3/4’’ x 3-3/8’’ x 42’’ (2) [PF 6017] 1-3/8’’ x 3-3/8’’ x 83’’ A-FRAME LEGS (2) [PF 6
PAGE 8
TOWER MODULE SA6051 / SA6022 COMPONENTS CONT.
PAGE 9
TOWER MODULE SA6051 / SA6022 HARDWARE 5/16”-18 x 6” Carriage Bolt (x3) 1/4”-20 x 1-1/4” Hex Bolt (x12) 5/16”-18 x 2-1/2” Hex Bolt (x2) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 4” Hex Bolt (x5) 5/16”-18 x 7” Hex Bolt (x1) 5/16”-18 x 8-1/2” Hex Bolt (x1) 1/4’’ Washer (x16) 5/16” Washer (x24) 5/16’’ Loc Washer (x12) 5/16” Loc Nut (x9) 1/4’’ Loc Washer (x12) #12 x 3/4” Truss Screw (x14) 5/16” Wood Loc Washer (x3) 1/4’’ x 1-3/4” Pan Screw (x4) 3/16” Tarp Washer (x7
PAGE 10
TERRACE MODULE SA6001 BOARD LIST (1) [PF 6061] 1-1/2’’ x 1-1/2’’ x 40’’ (2) [PF 6028] 1-3/8’’ x 3’’ x 79’’ (2) [PF 6026] 1’’ x 3-3/8’’ x 42’’ (3) [PF 6005] 3/4’’ x 3-3/8’’ x 42’’ (4) [PF 6025] 3/4’’ x 3-3/8’’ x 29-1/4’’ (3) [PF 6024] 3/4’’ x 3-3/8’’ x 27-3/4’’ (2) [PF 6150] 3/4’’ x 3-3/8’’ x 24-3/4’’ (1) [PF 6023] 3/4’’ x 3-3/8’’ x 22-1/2’’ (1) [PF 6022] 3/4’’ x 3-3/8’’ x 19-1/2’’ (10) [PF 6021] 5/8’’ x 5-3/8’’ x 30-3/4’’ (6) [PF 6135] 3/4’’ x 5-3/8’’ x 26-1/4’’ TERRACE HARDWARE 5/16’’ Loc Washer (x4) 1-3
PAGE 11
LADDER MODULE SA6005 BOARD LIST PICNIC TABLE MODULE SA6018 BOARD LIST (1) [PF 6034] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-L (1) [PF 6040] 1’’ x 5-3/8’’ x 41-1/2’’ BENCH (1) [PF 6035] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-R (2) [PF 6133] 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE (1) [PF 6029] 5/8’’ x 3-3/8’’ x 20-1/2‘’ (2) [PF 6038] 3/4’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG (5) [PF 6032] 1’’ x 3-3/8’’ x 18-1/2’’ (2) [PF 6037] 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT (2) [PF 6039] 3/4’’ x 3-3/8’
PAGE 12
FORT ENCLOSURE BOARD LIST (7) [PF 6407] 5/8’’ x 5-3/8’’ x 29-5/8’’ (1) [PF 6408] 3/4’’ x 5-3/8’’ x 41-1/2’’ (1) [PF 6410] 3/4’’ x 5-3/8’’ x 41-1/2’’ ARCHED (1) [PF 6409] 3/4’’ x 3-3/8’’ x 41-1/2’’ (2) [PF 6415] 1-3/8’’ x 1-3/8’’ x 3-3/8’’ (4) [PF 6416] 1-3/8’’ x 1-3/8’’ x 5-3/8’’ FORT ENCLOSURE HARDWARE 2-1/2” Deck Screw (12) 30mm Deck Screw (x40) 12
PAGE 13
STEP 1 6’’ 47-1/2’’ Flush 6’’ (3) 2-1/2’’ Screws /8’’ 9-5 5 x /8’’ 3-3 SE x ’ A ’ 3/4 ME B 3 6 RA 60 A-F PF (3) 2-1/2’’ Screws 1’’ 010 6 PF ’’ -3/8 3 x /2’’ 7-1 4 x T-Nut Small PF 6164 3’’ x 3’’ x 94’’ 59-1/4’’ PF 6164 3’’ x 3’’ x 94’’ (2) 2-1/2’’ Screws 57-9/16’’ PF /8’’ 3-3 x ’’ 3/4 6 0 60 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer /2’’ 4-1 4 x FRAME A (2) 2-1/2’’ Screws 1-1/2’’ BOTH SIDES Hint!! Use parts from your Tower Box. 2-1/2” Deck Screw (x14) 1.
PAGE 14
STEP 2 6’’ (3) 2-1/2’’ Screws Flush 6’’ PF 6164 3’’ x 3’’ x 94’’ (3) 2-1/2’’ Screws ’’ 5/8 59x /8’’ 3-3 SE x BA /4’’ 3 3 AME 6 0 R 6 A-F PF 0 601 F P /8’’ 3-3 x 1’’ PF 6164 3’’ x 3’’ x 94’’ 47-1/2’’ /2’’ 7-1 4 x T-Nut Small (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 57-9/16’’ PF ’’ 3/4 6 0 60 ’’ x -3/8 3 x 5/16’’ Washer ’’ 1/2 44- 5/16’’Loc-Washer (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 59-1/4’’ 31’’ 6 600 F P /8’’ 3-3 x ’’ 3/4 /2’’ 4-1 4 x (2) 2-1/2’’ Screws FRAME B 1-1/2’’ AL
PAGE 15
STEP 3 PF 600 53 /4’’ x (3) 2-1/2’’ Screws Check to make sure structure is square PF 600 53 /4’’ x Flush 3-3 /8’’ x 42’ ’ (3) 2-1/2’’ Screws PF 600 43 /4’’ x 3-3 /8’’ x 42’ ’ 59-1/4’’ Flush (2) 2-1/2’’ Screws PF 600 53 /4’’ x 3-3 /8’’ x 42’ ’ (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x11) 1. Attach support boards to Frame A as shown.
PAGE 16
STEP 4 (3) 2-1/2’’ Screws Check to make sure structure is square (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME B (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x11) 1. Attach Frame A to Frame B as shown.
PAGE 17
STEP 5 (3) 2-1/2’’ Screws (2) PF 6149 1-3/8’’ x 3-3/8’’ x 15-1/2’’ DECK SUPPORT Flush Flush (3) 1-3/4’’ Screw per joint (4) 3’’ Screw 1-3/4” Deck Screw (x6) 3” Deck Screw (x4) 1. Install Deck Supports as shown.
PAGE 18
STEP 6 PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (6) 1-3/4’’ Screws (6) 1-3/4’’ Screws PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (2) 2-1/2’’ Screws PF 6011 1’’ x 3/8’’ x 47-1/2’’ 16-1/2’’ 16-1/2’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6011 1’’ x 3/8’’ x 47-1/2’’ 1-3/4” Deck Screw (x12) TOP VIEW 2-1/2” Deck Screw (x2) 1. Install Deck Boards as shown.
PAGE 19
STEP 7 (7) PF 6008 3/4’’ x 5-3/8’’ x 42’’ (6) 1-3/4’’ Screws per deck board All Boards Flush With 3’’ x 3’’s 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 3/8’’.
PAGE 20
STEP 8 PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ Flush (2) 2-1/2’’ Screws Flush With 3’’ x 3’’s PF 6002 3/4’’ x 3-3/8’’ x 22-1/2’’ (2) 2-1/2’’ Screws (3) 2-1/2’’ Screws Flush With Bottom of Deck Flush (2) PF 6005 3/4’’ x 3-3/8’’ x 42’’ (3) 2-1/2’’ Screws 31’’ (3) 2-1/2’’ Screws per joint 2-1/2” Deck Screw (x16) 1. Attach Boards as shown.
PAGE 21
STEP 9 Check to make sure structure is square x 1’’ 026 6 PF x /8’’ 3-3 ’ 42’ 47-1/4’’ (2) 2-1/2’’ Screws FRAME A 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer Hint!! Use parts from your Terrace Box. T-Nut Small 2-1/2” Deck Screw (x4) 1. Install Deck Support Board as shown.
PAGE 22
STEP 10 Check to make sure structure is square PF ’’ x 3/4 5 600 x /8’’ 3-3 ’ 42’ COUNTERBORE THIS SIDE PF 6028 1-3/8’’ x 3’’ x 79’’ COUNTERBORE THIS SIDE ’’ 3/4 5 0 60 PF ’’ x -3/8 3 x PF 6028 1-3/8’’ x 3’’ x 79’’ (3) 2’’ Screws Flush Flush (3) 2’’ Screws ’ 42’ 45-9/16’’ (3) 2’’ Screws (3) 2’’ Screws FRAME C 2” Deck Screw (x12) 1. Assemble Frame C as shown.
PAGE 23
STEP 11 Check to make sure structure is square ’’ 61 2 0 6 PF ’’ x -3/8 3 x ’ 42’ 5/16-18 X 2’’ Hex Head Bolt 47-1/4’’ 5/16’’Loc-Washer 5/16’’ Washer (2) 2’’ Screws T-Nut Small 2” Deck Screw (x4) 1. Install Deck Support Board as shown.
PAGE 24
STEP 12 Flush With Outside Face of 1-3/8’’ x 3’’ (2) 2-1/2’’ Screws Check to make sure structure is square PF ’’ x 3/4 5 602 ’’ 1/4 29x /8’’ 3-3 Flush With Top of Frame Flush With Top of Frame ’’ 025 29-1/4 6 PF 8’’ x -3/ x3 ’ ’ 4 3/ Flush With Outside Face of 1-3/8’’ x 3’’ (2) 2-1/2’’ Screws Flush With Outside Face of 1-3/8’’ x 3’’ (2) 2-1/2’’ Screws ’’ 024 27-3/4 6 PF 8’’ x -3/ x3 ’ ’ 4 3/ Flush With Outside Face of 1-3/8’’ x 3’’ FRAME C PF 2-1/2” Deck Screw (x8) 1.
PAGE 25
STEP 13 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws 79’’ (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME C 2-1/2” Deck Screw (x10) 1. Attach Frame C to Tower as shown.
PAGE 26
STEP 14 (2) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws (1) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (1) 1-3/4’’ Screws 10-5/8’’ 10-5/8’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ TOP VIEW 1-3/4” Deck Screw (x10) 1. Install Deck Boards as shown.
PAGE 27
STEP 15 (6) PF 6135 3/4’’ x 5-3/8’’ x 26-1/4’’ All Boards Flush (6) 1-3/4’’ Screws per board Note: Holes 1-7/8’’ From Edge on This Side 1-3/4” Deck Screw (x36) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 7/16’’.
PAGE 28
STEP 16 PF 6023 3/4’’ x 3-3/8’’ x 22-1/2’’ PF 6022 3/4’’ x 3-3/8’’ x 19-1/2’’ (3) 2’’ Screws 2” Deck Screw (x6) 1. Install Barrier Support Boards as shown.
PAGE 29
STEP 17 PF 6004 3/4’’ x 3-3/8’’ x 42’’ (6) 2-1/2’’ Screws PF 6005 3/4’’ x 3-3/8’’ x 42’’ 5-3/8’’ 53-7/8’’ 2-1/2” Deck Screw (x12) 1. Attach Gap Filler Boards as shown.
PAGE 30
STEP 18 1-7/8’’ (6) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ (4) 30mm Screws per board Panel Bracket (8) 3/4’’ Pan Screws #12 x 3/4” Pan Screw (x8) INSIDE VIEW 30mm Deck Screw (x16) 1. Install Barrier Boards as shown. No gaps between boards.
PAGE 31
STEP 19 1’’ 3-1/8’’ 3-1/8’’ 1’’ 1-5/8’’ PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 1/2’’ GAP PRE-DRILL (4) 1/8’’ HOLES 1/2’’ GAP PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 17-3/8’’ (4) 30mm Screws per board PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ 4-7/8’’ (10) 3/4’’ Screws per Window Frame PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 2-13/16’’ x2 30mm Deck Screw (x8) 2-13/16’’ x2 Hint!! Use parts from your Tower Box.
PAGE 32
STEP 20 1’’ (2) 30mm Screws per board (2) 30mm Screws per board (2) 30mm Screws per board (2) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws 30mm Deck Screw (x24) #12 x 3/4” Pan Screw (x8) 1. Install Window Panels.
PAGE 33
STEP 21 PF 6020 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT TOP OF BEAM SUPPORT 84’’ FROM BOTTOM OF POST Loc Nut 5/16’’ Washer Wood Loc-Washer 5/16-18 X 6’’ Carriage Bolt 1. Install Swing beam support as shown.
PAGE 34
STEP 22 PF 6019 2-11/16’’x5-3/8’’x93’’ Swing Beam 5/16’’ T-Nut Large 5-1/2’’ Swing Hanger Beam Clamp 2 1 3 x4 Correct Orientation 4 (4) 30mm Deck Screws 5 30mm Deck Screw (x24) 1. Attach Swing Hanger(s) to swing beam as shown. NOTE: Make certain hanger and plate are snug against the bottom of the swing beam, (Fig 5), before installing screws.
PAGE 35
STEP 23 PF 6018 2-11/16’’x3’’x62’’ A-Frame SB Support 5/16”-18 x 7” Hex Head Bolt (1) 3’’ Screws (1) 3’’ Screws 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 6017 1-3/8’’x3-3/8’’x83’’ A-Frame 5/16”-18 x 2-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Washer (2) 2-1/2’’ Screws 5/16”-18 x 4” Hex Head Bolt (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 5/16-18 T-Nut Small PF 6016 1-3/8’’x3-3/8’’x58’’ A-Frame Support 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut S
PAGE 36
STEP 24 (2) Swing Beam Bracket 5/16”-18 x 3-1/2” Hex Head Bolt x2 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/2” Hex Head Bolt 5/16” Washer x2 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
PAGE 37
STEP 25 Beam Brace 5/16”-18 x 3 1/4” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 1. Install Swing Beam Brace as shown.
PAGE 38
STEP 26 5/16”-18 x 6” Carriage Bolt 5/16”-18 x 8-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16” Wood Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Loc Nut 1. Install Swing Beam as shown.
PAGE 39
STEP 27 (6) PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ (4) 30mm Screws per board 30mm Deck Screw (x24) 1. Install Barrier Boards as shown. 39 BARRIER BOARD SPACING: 2XWHU ERDUGV ZLOO EH ÀXVK against 3’’ x 3’’ Uprights. All boards inbetween will have a 3/4’’ gap.
PAGE 40
STEP 28 (1) 3’’ Deck Screws 1-5/8’’ 1-5/8’’ 13-1/2’’ PF Check to make sure structure is square 60 62 PF ’’ 21 6 60 ’’ 3/8 x3 ’’ 1/2 2 x4 E AM R F AF O RO PF 6058 5/8’’ x 3-3/8’’ x 30’’ (4) 30mm Deck Screws 1’’ x3 -3 /8’ ’x 42 -1 /2’ ’R OO FA -F RA ME x2 3/4’’ CENTERED PF 6060 5/8’’ x 5-3/8’’ x 13’’ SUN (4) 30mm Screws x2 30mm Deck Screw (x12) 3” Deck Screw (x2) 1. Assemble Roof A-Frames as shown.
PAGE 41
STEP 29 (4) 30mm Screws (6) 30mm Screws (1) PF 6056 5/8’’ x 2’’ x 10’’ (2) PF 6059 5/8’’ x 2’’ x 7’’ x2 Note: Place screws through A-Frame and into end of PF 6053 CENTERED Note: PF 6053 Rests on Top of PF 6056 (2) 2-1/2’’ Screws /2’’ 1 43 PF 6053 1-3/8’’ x 3-3/8’’ x 43-1/2’’ SIDE VIEW (2) 2-1/2’’ Screws Note: Place screws through A-Frame and into end of PF 6053 /2’’ 1 43 30mm Deck Screw (x20) 2-1/2” Deck Screw (x4) 1. Assemble the Roof frame as shown.
PAGE 42
STEP 30 3/4’’ Offset Each Side (3) 1-5/8’’ Screws Side View (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws 1-5/8” Deck Screw (x12) 1. Attach Roof Frame to Tower as shown.
PAGE 43
STEP 31 (4) 2’’ Screws 43-1/2’’ -3/8’’ x 3 x ’’ /4 03 (4) PF 605 -1/2’’ /8’’ x 43 -3 3 x ’’ 3/4 PF 6050 2’’ Screws 2” Deck Screw (x8) 1. Attach Roof Side Support Boards as shown.
PAGE 44
STEP 32 (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer 3/4” Pan Head Screw (x6) 1. Attach Tarp as shown.
PAGE 45
STEP 33 x -3/8’’ 035 1 PF 6 ’’ 3-3/8 x 66- -1/4’’ RT-R 6 ’’ x 6 PPO 3-3/8 R SU E LADD 1/4’’ x -3/8’’ 034 1 PF 6 -L ORT UPP ER S LADD (2) 2-1/2’’ Screws per Rung (2) 2-1/2’’ Screws per Rung (5) PF 6032 1’’ x 3-3/8’’ x 18-1/2’’ PF 6029 5/8’’ x 3-3/8’’ x 20-1/2‘’ (4) 2-1/2’’ Screws 2’’ Hint!! Use parts from your Ladder Box. 2-1/2” Deck Screw (x24) 1. Assembly Ladder as shown.
PAGE 46
STEP 34 (3) 2-1/2’’ Screws Panel Bracket (4) 3/4’’ Pan Screw 2-1/2” Deck Screw (x3) #12 x 3/4” Pan Screw (x4) 1. Attach Ladder to Tower as shown.
PAGE 47
STEP 35 PF 6415 & PF 6416 Flush to Support Top View (4) PF 6416 1-3/8’’ x 1-3/8’’ x 5-3/8’’ PF 6452 1-3/8’’ x 3-3/8’’ x 22’’ (4) 1-3/4’’ Screws From Behind Deck Support (2) 2-1/2’’ Screws per block 53-7/8’’ Flush to Support Flush to Upright Underdeck View 31’’ 3-3/8’’ Flush to Top of Board (2) PF 6415 1-3/8’’ x 1-3/8’’ x 3-3/8’’ (2) 2-1/2’’ Screws per block 1-3/4” Deck Screw (x4) PF 6452 1-3/8’’ x 3-3/8’’ x 22’’ 2-1/2” Deck Screw (x12) 1. Attach support boards as shown.
PAGE 48
STEP 36 (2) 1-5/8’’ Screws per side PF 6410 3/4’’ x 5-3/8’’ x 41-1/2’’ ARCHED (2) 2-1/2’’ Screws per side Flush Flush Flush PF 6024 3/4’’ x 3-3/8’’ x 27-3/4’’ Flush PF 6408 3/4’’ x 5-3/8’’ x 41-1/2’’ (2) 1-3/4’’ Screws per side 31’’ Flush PF 6409 3/4’’ x 3-3/8’’ x 41-1/2’’ (2) 1-3/4” Screws per side Flush Flush 30mm Deck Screw (x28) 1-1/4” Deck Screw (x16) (4) 1-1/4’’ Screws per board 1-5/8” Deck Screw (x4) 1-3/4” Deck Screw (x8) (4) 30mm Screws per board 1-3/4’’ GAP 2’’ GAP (4) PF 6021
PAGE 49
STEP 37 ALIGN SCREWS WITH PRE DRILLS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD (6) PF 6389 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARDS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD 2” Deck Screw (x32) 1. Align and install rock wall boards to the image above.
PAGE 50
STEP 38 (3) 2-1/2’’ Screws per side Under Deck View 2-1/2” Deck Screw (x6) 1. Attach Rock Wall as shown.
PAGE 51
STEP 39 (2) 1/4’’ T-Nuts (2) 1-1/4’’ Hex Head Bolts (2) 1/4’’ Flat Washer Per Rock (2) 1/4’’ Loc-Washer Per Rock 1. Attach Climbing Rocks as shown.
PAGE 52
STEP 40 (2) PF 6039 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT (2) PF 6037 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT 3’’ (4) 1-1/4’’ Screws 2-3/4’’ 3’’ 11-1/4’’ (4) 1-1/4’’ Screws (4) 2’’ Screws (2) PF 6133 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE OUTSIDE FACE TO OUTSIDE FACE, BOTH SIDES (4) 2’’ Screws 2-3/4’’ 6-7/8’’ OUTSIDE FACE TO OUTSIDE FACE, BOTH SIDES 6-7/8’’ (2) PF 6038 1’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG (2) 2’’ Screws 36’ ’ (2) 2’’ Screws PF 6040 1’’ x 5-3/8’’ x 41-1/2’’ BENCH Check
PAGE 53
STEP 41 1-1/4” Truss Screws 1-1/4” Truss Screws Grade 3’’ Side View 2” (2) 30mm Deck Screws PF 5999 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake 30mm Deck Screw (x2) 1. Attach slide as shown.
PAGE 54
STEP 42 k Dec o t sh Flu (6) 30mm Screws (2) PF 6180 5/8’’ x 3-3/8’’ x 10-1/2’’ Under Deck View Grade 1-1/4” Truss Screws 2” (2) 30mm Deck Screws PF 6009 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake 30mm Deck Screw (x8) 1-1/4” Truss Screw (x3) 1. Attach slide support boards as shown. 2. Attach slide as shown.
PAGE 55
STEP 43 Back View Front View (2) 1/4” Washer (2) 1/4’’ x 1-3/4” Pan Screw 11” 1/2” Pan Screw (x2) 1-3/4” Pan Screw (x4) 1. Attach Safety Handle and I.D. Tag as shown.
PAGE 56
STEP 44 Wind Rider 2 1 Loc-Nut 3 51” Un-Coated chain 5/16’’ Flat Washer QuickLink 5/16’’ Flat Washer 5/16”-18 x 6-1/2” Hex Bolt QuickLink Wind-Rider 4 Wind Rider Assembly 1. Insert Seat into Handle as shown in (Step1). Secure in place with hardware shown. Note: Make certain no more than two bolt threads protrude from the Loc-Nut once fully tightened. 2. Insert (1) Quick Link into the end of each length of chain, as shown in (Step 2). Make certain the Quick Link is positioned as shown. 3.
PAGE 57
BOTTOM OF SEAT LOGO ON TOP BOTTOM OF SEAT PLASTIC COATED END LOGO ON TOP STEP 45 Swing Seat Assembly 1. Take one length of chain and place the outermost link of coated chain through the Quick Link as shown. 2. Place the Quick Link through the Grommet of the swing seat as shown. 3. Tighten the threaded sleeve of the Quick Link with a suitably sized wrench so that the seat is securely attached and the Quick Link cannot be easily loosened. Repeat for second chain, Quick Link and Swing Seat Grommet. 4.
PAGE 58
STEP 46 5/16” Washer Fold up Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 3ODFH VZLQJ VHW LQ ¿QDO ORFDWLRQ DQG PRXQW $QFKRU ,W V DW ORFDWLRQV FLUFOHG DERYH 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
PAGE 59
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY WARRANTY REGISTRATION: Please complete your warranty registration to properly validate your product warranty. Register your product online at: www.OnlineWarranty.net Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty SURYLGHV FRQ¿GHQFH DQG GHPRQVWUDWHV RXU FRPPLWPHQW WR providing quality residential playground products.
PAGE 60
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration %HQH¿WV RI UHJLVWHULQJ RQOLQH Ŷ Quick & simple from home or mobile Ŷ Record your purchase in our system Ŷ Initiate product warranty Ŷ Improved customer support Ŷ 1RWL¿FDWLRQ RI QHZ SURGXFW LQIRUPDWLRQ Register your product online at www.OnlineWarranty.