2281-WR - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll-free number: 1-800-844-9273 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST or email: customerservice@backyard-play.
4HIS PAGE INTENTIONALLY LEFT BLANK
2281-WR Customer Service Backyard Play Systems 1-800-844-9273 Playset 1000 Ternes Drive Monroe, MI 48162 4/21/2014 Model 4140 Model 6201 Recommended for Ages 3 to 11 BEFORE YOU YOU BEGIN BEGIN --- BEFORE Tools Required Socket Set Hammer Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin. If you have purchased accessories to accompany this play set, please read all installation instructions before beginning assembly of this structure.
ASSEMBLY SAFETY and HELPFUL HINTS STOP!!! Check all parts and hardware before beginning. If any parts are missing or damaged please circle and call the phone number listed. DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET ! KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE AND MAINTENANCE REFERENCE. To aid in making your playset assembly easier, here is a listing of some helpful hints. Wear safety glasses during drilling, assembly of your playset.
ASSEMBLY SAFETY and HELPFUL HINTS Please read carefully. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. This playset has been designed for use by a maximum of eight occupants at one time having a combined weight of 1,200 pounds. (This weight does not include occupants in the sandbox area.) This playset is recommended for children (3) through (11) years of age. On-site adult supervision for children of all ages is recommended.
Periodic maintenance is required to ensure safe enjoyment of your playset and optional accessories. Observing the following procedures reduces the likelihood of serious or fatal injury. Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and tighten as required. T-nuts should be inspected for full and proper seating into the wood.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM SpeciÀcation F 1292.
PLAYSET ORIENTATION *Hint* Throughout this manual references made to the Left Side, the Right Side, the Front Side and the Back Side of the playset serve as a consistent reminder to help with assembly.
IMPORTANT! Use these Assembly Procedure Hints throughout the installation process. 1. All Lag Bolts must have pre-drilled holes. Use a 1/4” drill bit for all 3/8” Lag Bolts. Use a 3/16” drill bit for all 5/16” Lag Bolts. Pre-drilling pilot holes will help prevent Screws and Lag Bolts from breaking and wood from splitting during assembly. DO NOT OVER-TIGHTEN LAG BOLTS 2. In areas where drilling a larger 1/2” hole is neccessary, such as when installing T-Nuts, (Fig.
WOOD PARTS LIST 5/4 x 4 x 45-1/8” 5/4 x 4 x 45-1/8” 5/8 x 3-1/4 x 10” WOOD SIZE CONVERSION CHART Nominal Board Size 2526-ST x1 2501-ST x9 2513-ST x4 5/4 x 4 x 45-1/8” 1 x 3 x 54" 5/4 x 6 x 23-3/4” Actual Size 1" x 4" ..........................................3/4" x 3-3/8" 1" x 6" .......................................... 3/4" x 5-3/8" 5/4" x 4" ..........................................1" x 3-1/2" 5/4" x 6"... .......................................1" x 5-1/2" 2" x 4"............................
H A R D W A R E 90o Angle Bracket Plate 2485 Swing Beam 90o Plate Swing Beam Angled Plate Left 2449 x1 x1 Swing Beam Angled Plate Right 2448 x1 2447 x1 2412 x2 2438 x1 2451 x6 2405 x3 2603 x1 Swing Beam Flat Plate Swing Hanger 2631 x6 2411 Swing Green Climbing Rocks 2434 x2 2097 x1 Plaque Slide Safety Handle E S S O R I E S Swing Yellow x1 x4 C 2180 x1 Steering Wheel A C Telescope 2654 -or- 2099 x1 2073 9 x1
3/8” LOCK NUT 5/16” T - NUT 3/8” x4 3/8” T - NUT x44 x14 3/8” LOCK WASHER 3/8” FLAT WASHER 3/4” E N 3/8” 3/8” 2-1/2” PAN HEAD SCREW 1/4” x 1” FENDER WASHER 3/16” x 1” FENDER WASHER A S T x76 x61 x19 E R S TRUSS HEAD SCREW x12 x11 1” 2-1/2” 5/16” FLAT WASHER 5/16” LOCK WASHER Y S E T F x14 1” P L A x4 x4 5/16” 2452 Bag 1/4” ROCK WALL HARDWARE Lock Washer 1-1/2” x12 5/16” 1/4” SAFETY HANDLE HDW.
3/8” HEX HEAD BOLTS x2 x8 x2 1-3/4” 2” 2-1/4” x30 3-3/4” x2 3/8” 3/8” P 3/8” L 6” A x1 Y x1 E 3/8” S 1-1/4” 1-1/2” #2 SQUARE DRIVE BIT T 3/8” F A x1 3/8” S 3/8” LAG BOLT T E 3/8” N 3/8” LAG BOLT WOODSCREWS E 3/8” LAG BOLT x30 1-5/8” 4” x215 x70 2” 2-1/2” 3” 3” 2-1/2” x85 1-1/4” 11 S x8 x98 R x1
A C T U A L x6 x2 S I E x2 3-3/4" 3-1/2" Z S H O W N x2 4-1/2" x1 6-1/2" 9" 3/8" 3/8" 3/8" 3/8" BUTTON HD. SCREW x2 1-1/2” BUTTON HD.
SET-UP SAFETY AREA BACK SIDE 24’-10” 6’ SAFETY AREA ROCK WALL SWING 10’-8” HEIGHT 13'-4" 12’-10” SLIDE 27’-6” RIGHT SIDE LEFT SIDE 13’-4" 6’ SAFETY AREA 6’ SAFETY AREA LADDER FRONT SIDE FORT CORNER POSTS 3” Wood Screw 3-3/4” Hex Bolt Lock Washer Flat Washer x4 Note 1 hole location. x4 Flush 5/4 x 4 x 45-1/8” 2526-ST x1 x6 T-Nut Flush Hole for Climbing Rope 47” 4” 2501-ST x1 Flush 90° 5/4 x 4 x 45-1/8” Note 2 hole locations.
BASE FORT FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE x2 3-3/4” Hex Bolt Lock Washer Flat Washer x4 3” Wood Screws 5/4 x 6 x 45-1/8” 2507-ST x1 90° Flush Align braces with pre-drilled holed Ensure all bracing is square before installing wood screws Flush FORT CORNER POSTS Ensure all bracing is square before installing wood screws Large holes toward top 5/4 x 4 x 45-1/8” 2501-ST x4 x6 x6 T-Nut Flat Washer Lock Washer 3-3/4” Hex Bolt 5/4 x 6 x 71-3/4” 2508-ST x1 Flush Flush 5/4 x 6 x 45-1/
FORT CORNER POSTS 3” Wood Screw x4 3-3/4” Hex Bolt Lock Washer Flat Washer x4 Note 1 hole location. Flush 5/4 x 4 x 45-1/8” 2501-ST x1 47” T-Nut Flush x6 2501-ST x1 5/4 x 4 x 45-1/8” Flush 90° Note 2 hole location.
FORT FLOOR FRAME Align braces with pre-drilled holed x6 3-3/4” Hex Bolt Lock Washer Flat Washer T-Nut FORT FLOOR FRAME Ensure 47” measurement from bottom of base to top of Àrst deck 3” Wood Screws x16 47” Reinforce bracing with 3” wood screws at all pre-drilled holes 16 47”
FORT DECK CLEAT 5/4 x 4 x 45-1/8” EQUA L x1 2516-ST EQUA L EQUA L EQUA L Flush 2-1/2” Wood Screws x4 Flush FORT DECK PLANKS x28 5/4 x 6 x 45” 2509-ST x7 2-1/2” Wood Screws evenly spaced 1-5/8” Wood Screws Flush x14 17
FORT DECK PLANKS 5/4 x 4 x 39” 2510-ST x2 x8 2-1/2” Wood Screws 1-5/8” Wood Screws x4 SLIDE SLIDE BLOCK 2” Wood Screws x2 FLUSH 2" 2785-ST x1 2 x 4 x 16-3/8” 18
FORT DECK SUPPORT Repeat for all (4) 1020-ST Braces 1020-ST Flush with outside. Flush Pre-Drill (2) 1/8” Pilot Holes. 2” Wood Screw x8 Flush Flush Pre Drill 1/8” Hole Flush 1020-ST x4 3” Wood Screw 2 x 4 x 18” x8 FORT DECK RAILS Mark and drill 1/4” x 2” DEEP pre-drill before installing lag bolts. 3” Lag Bolt Lock Washer Flat Washer x4 5/4 x 4 x 45-1/8” 2501-ST x2 Flush at all corners. Bottom Áush with bottom of deck 3” Wood Screws Flush at all corners.
SWING BEAM SUPPORT INSTALL NOTE: DEPENDING ON THE FASTENERS PROVIDED THERE ARE TWO METHODS TO INSTALL 2505-ST SWING BEAM SUPPORT. LOCATE EITHER SET OF FASTENERS SHOWN BELOW AND INSTALL ACCORDINGLY. IF YOU HAVE (X2) 6" HEX BOLTS IN YOUR KIT, INSTALL USING METHOD A. IF YOU HAVE (X4) 6-1/2" CARRIAGE BOLTS IN YOUR KIT INSTALL USING METHOD B.
METHOD B SWING BEAM SUPPORT 6-1/2" Carriage Bolt Torque Washer 6-1/2" Carriage Bolt Torque Washer Flat Washer Small Holes UP Lock Nut 2505-ST x1 SIT ON RAIL 4 x 4 x 45-1/8” Flat Washer Lock Nut Tap Carriage Bolt and Torque Washer into place FORT x4 TENT FRAMING 3-3/4” Hex Bolt Lock Washer Flat Washer 5/4 x 4 x 71-3/4” 2500-ST x2 T-Nut x4 21
ROOF RAFTERS Pre-drill 1/8" pilot holes 2" DEEP. Install one 3" wood screw to secure 2579-ST’s.
ROCK WALL ASSEMBLE Place and align planks parallel on a level surface. We recommend a soft surface to protect planks. *Hint: Number the order of each plank for correct re-orientation, top to bottom. Mark parts on back side or use masking tape. Arrange ALL the Rocks in an attractive and practical fashion. Position Rocks between pre-drilled holes in planks. DO NOT position Rocks over any pre-drilled holes. Mark hole position of each Rock in final decided position.
ROCK WALL ASSEMBLE Turn all planks over to original position. Align two Rails parallel and maintain dimension shown. Position Plank 2 as shown and attach to Rails. - Do not attach any other planks at this time. 9 2520-ST x1 7 2 x 4 x 51” 23-3/4” 8 6 Flush Outside Dimension 5 4 3 2-1/2” Wood Screws x4 1 2 5-1/4” 23-3/4” 2 Outside Dimension Flush 5-1/4” ROCK WALL ASSEMBLE Place Planks 3 through 9 onto Rails, flush to each other.
ROCK WALL INSTALL Secure remaining Planks (3 through 8). Ensure all Plank ends are flush, making sure screws install into rails. - Do Not attach top Plank 1 at this time. 23-3/4” 9 All flush 2-1/2” Wood Screws x24 8 7 6 5 4 3 2 23-3/4” 2 ROCK WALL ASSEMBLE 2451 x1 BAG 1/4” x 1-1/2” Hex Bolts 1/4” Lock Washers 1/4” Flat Washers 2 T-Nuts 1 Do NOT attach top board at this time.
ROCK WALL ASSEMBLE x2 2 5/16” T-Nut 5/16 x 1-1/2” Button Head Screw 5/16” Lock Washer L-Bracket 5/16”Flat Washer x2 2412 ROCK WALL INSTALL Flush Align ladder with inside of post and top of cross brace and mark holes.
ROCK WALL INSTALL BACK SIDE Rock Wall SEE PAGE 7 Pre-drill two 1/4" pilot holes at marked locations. Re-drill holes from opposite side using 3/8" bit.
INSTALL ROCK WALL 5/4 x 4 x 17” x1 2222-ST Flush Flush 2-1/2” Wood screws x4 ROCK WALL INSTALL x2 5/16” Flat Washer 5/16” Lock Washer 5/16 x 1-1/4 Button Head Screw x2 Secure middle brace with (2) 2-1/2” Wood Screws from behind.
INSTALL ANGLE BRACE & ROCK WALL Pre drill 3/16" pilot holes, 2” DEEP for lag bolt. x4 2-1/2” Wood screws 5/4 x 6 x 23-3/4” Flat Washer Lock Washer 4” Lag Bolt x1 2519-ST 2” x 4” x 47-3/4” 2515-ST x1 T-Nut Align pre-drilled holes 2-1/4” Hex Bolt Lock Washer Flat Washer INSTALL FORT BRACING Pre-drill 3/16" pilot hole Re-drill through hole from opposite side using 7/16" bit.
SWING BEAM SWING HANGERS - INSTALL Swing Beam 1-3/8” Washer Swing Hanger Bolt Swing Hanger 1-3/8" Washer IMPORTANT! Final position of each Spring Clip is perpendicular to swing beam. 2631-B Swing Hanger x6 Spring Clip IMPORTANT! Insert Swing Hanger and hand-tighten until hanger meets swing beam. Use a screwdriver to keep swing hanger in position while tightening lock nut. Based on your Playset, you may have You may need to tap with hammer to get though holes. additional swing beam hardware.
UPRIGHT INSTALL x2 L EQUA L EQUA 1-3/4” Hex Bolt Lock Washer Flat Washer T-Nut 2505-ST x1 5/4 x 4 x 47” 2539-ST Center 2539-ST. Mark and Pre drill 7/16" through holes for hex bolt. A - FRAME ASSEMBLE T-Nut x2 2525-W x2 3 x 3 x 95" Rotate 2525-W 180o after installing T-Nuts.
A - FRAME ASSEMBLE x2 3-3/4” Hex Bolt Lock Washer Flat Washer Pre-installed T-Nuts are underneath.
A - FRAME INSTALL 2499 x1 x2 3-3/4” Carriage Bolt Lock Nut Flat Washer 2525-W SWING BEAM INSTALL 3-1/2 x 5-1/2” x 95” DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME 2752-W x1 x2 Flat Washer Lock Nut x1 2448 4-1/2” Carriage Bolt x2 x1 NOTE: You may need to tap bolts with hammer to get though holes.
SWING BEAM INSTALL Position swing beam assembly resting upon A-frame A - FRAME SWING Align holes and insert carriage bolt. Repeat where arrows are shown. NOTE: You may need to tap bolts with hammer to get though holes.
SWING BEAM ASSEMBLY INSTALL 6-1/2” Carriage Bolt Torque Washer You may need to tap with hammer to get though holes. Flat Washer Lock Nut SWING SWING BEAM Position swing beam assembly resting upon plate and align with holes. x1 x1 9” Carriage Bolt 6-1/2” Carriage Bolt x1 Torque Washer 2485 x1 x2 Flat Washer Lock Nut NOTE: You may need to tap bolts with hammer to get though holes.
SWING 1. Pre-drill using 3/16” bit. 2. Re-drill from opposite side using 7/16” bit.
SWING LEVEL Level swing beam and tighten all swing beam fasteners Mark and drill 1/4” x 2” DEEP pre-drill before installing lag bolts.
BALUSTERS FORT 3-1/4” 3-1/4” 3-1/4” 3-1/4” 3-1/4” 3-1/4” Install Àrst ballusters 1” from upright 2539-ST and deck. 1-1/4” Wood screws SPACER SPACER 2539-ST SPACER SPACER x24 2523-ST x6 5/8 x 3-1/4 x 29-3/4” 1” space BALUSTERS FORT CENTER Center Àrst spacer and intall ballusters Áush to deck.
BALUSTERS FORT 3-1/4” Align spacer with inside of post and intall Àrst balluster 1-1/4” Wood screws SPACER x8 x2 2537-ST 5/8 x 3-1/4 x 33” 1-1/4” 3-1/4” ROOF/CANOPY INSTALL FLUSH LEVEL FLUSH FLUSH FLUSH 2512-ST x2 5/8 x 3-1/4 x 35-3/4” 1-5/8” Wood Screws x8 DO NOT OVER-TIGHTEN SCREWS. KEEP SCREW HEAD FLUSH WITH TOP OF BOARD.
ROOF/CANOPY INSTALL Center 2513-ST on 2512-ST with mark and secure using two 1-5/8” screws. Pre-drill 1/8” hole to prevent splitting. 5/8 x 3-1/4 x 10” 2513-ST x4 1-5/8” Wood Screws x8 FLUSH FLUSH R CENTE R CENTE FLUSH DO NOT OVER-TIGHTEN SCREWS. KEEP SCREW HEAD FLUSH WITH TOP OF BOARD. ROOF/CANOPY INSTALL Install 2511-ST centered and Áush to bottom of 2512-ST using two 1-5/8” screws from inside. 1-5/8” Wood Screws x8 FLUSH Pre-drill 1/8” hole to prevent splitting.
ROOF PLANKS INSTALL Center roof boards on rafters. Ensure equal overhang on both sides; about 15/16". 7/16" 2-1/2" Wood Screws x8 7/16" Maintain 43-1/8" dimension between rafters. 43-1/8" Flush at peak. 2783-ST x2 5/4 x 6 x 47" WARNING! Install screws Áush with roof board to avoid protruding below roof. ROOF PLANKS INSTALL Install 3 roof slats on both sides of roof. 2-1/2" Wood Screws Install all roof boards Flush.
ROOF PLANKS INSTALL Install 7 remaining roof slats on each side. 5/4 x 6 x 47" 2782-ST x12 2-1/2" Wood Screws x56 WARNING! Install screws Áush with roof board to avoid protruding below roof. 2783-ST x2 5/4 x 6 x 47" ROOF PLANKS INSTALL Install cleat (2574-ST) centered under planks on both sides of roof. Install Àrst screws into cleat at bottom plank. WARNING! Install screws Áush with roof board to avoid protruding below roof.
SWINGS INSTALL Attach Playset Plaque using One 1" Philips Head Screw (provided) at each corner of Plaque. 2180 x1 2434 2097 2434 SWING SWING SWING 8" Minimum when occupied. Adjust chains at Top. All Spring Clips must not be removable unless using tools.
STEERING WHEEL INSTALL Install on 2539-ST aligned with swing beam inside fort.
INSTALL STAKES x4 1015 3” Wood Screws x8 1 x 1-3/8 x 17” Make sure all base pieces and uprights are resting Áat on the ground. 3” Wood Screws x4 It may be necessary to loosen the soil beneath Playset to make everything level. 1015 1 x 1-3/8 x 17” This space intentionally left blank.
SLIDE INSTALL NOTE: IF SLIDE HAS TWO HOLES, INSTALL SCREWS 3-1/2" FROM FRONT OF DECK. 2-1/2” Pan Head Wood Screw x2 1/4 x 1” Fender Washer x2 Locate Slide in the opening between Balusters on the FRONT SIDE of the Tower. 3-1/2” 2099 x1 3-1/4” Pre-drill 1/8” pilot holes through Slide at dimples, through deck planks, and into lower slide support. FRONT SIDE SLIDE Ensure screws are installed through deck planks. Move slide slightly to avoid spaces between planks.
SLIDE SURFACING MATERIAL (not supplied) NOTE: ONLY INSTALL GROUND STAKE IF SLIDE HAS THREE HOLES. DO NOT INSTALL IF SLIDE HAS TWO HOLES. Apply Surfacing Material at recommended depth, or deeper. Hammer 1015 Ground Stake into ground on either side of slide and attach to slide wall using (2) 1" Screws.
SANDBOX SEATS INSTALL 5/4 x 6 x 22-1/2” 1120-ST x2 2-1/2” Wood Screws x8 Flush Flush This space intentionally left blank.
CLIMBING ROPE INSTALL OPTIONAL: Tie several single knots in locations to allow logical hand-grab points. Step 1 Feed top of Climbing Rope through front of Upper Rail ( 2526-ST ) and tie a double knot on the back side (Fig. 1). Step 2 Feed lower end of Climbing Rope through hole in Rock Wall board ( 2527-ST ) and tie a double knot on the back side (Fig. 1). Fig. 1 For Safety, insure that the rope is tight enough so that it can not be looped back on itself.
WARRANTY Backyard Play Systems warrants the following: 1. All wood and plastic (polymer) coated wood components have a Limited Lifetime Warranty. • Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unÀt due solely to damage caused by fungal decay or termites. • Plastic (Polymer) Coated Woodguard TM – Backyard Play Systems will replace Woodguard TM components which become structurally unÀt due solely to damage caused by fungal decay or termites.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
2271 - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll-free number: 1-866-890-2211 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST or email: customerservice@backyard-play.
(This page intentionally left blank.
2271 Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 48162 Backyard Play Systems Monkey Bar Accessory 11/01/2012 Model 4071 4081 Recommended for Ages 3 to 11 - BEFORE YOU BEGIN - Tools Required Socket Set Ratchet Socket Extension Hammer 5 lb. Sledge First... Adult Assistance required Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin.
ASSEMBLY SAFETY and HELPFUL HINTS STOP!!! Check all parts and hardware before beginning. If any parts are missing or damaged please circle and call the phone number listed. DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET ACCESSORY! KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE AND MAINTENANCE REFERENCE. To aid in making your playset assembly easier, here is a listing of some helpful hints. Wear safety glasses during drilling, assembly of your playset accessory.
SAFETY WARNINGS Please read carefully. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. This playset accessory is recommended for children (3) through (11) years of age. On-site adult supervision for children of all ages is recommended. Instruct children not to walk close to, in front of, behind, or between moving items.
MAINTENANCE Periodic maintenance is required to ensure safe enjoyment of your playset and optional accessories. Observing the following procedures reduces the likelihood of serious or fatal injury. Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and tighten as required. T-nuts should be inspected for full and proper seating into the wood.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
MONKEY BAR PARTS LIST WOOD SIZE CONVERSION CHART Nominal Board Size Actual Size 1“ x 4”..........................................3/4” x 3-3/8” 1“ x 6”..........................................3/4” x 5-3/8” 5/4“ x 4”.....................................15/16” x 3-3/8” 5/4“ x 6”.....................................15/16” x 5-3/8” 2“ x 4”.......................................1-3/8” x 3-3/8” 2“ x 6”.......................................1-3/8” x 5-3/8” 4“ x 4”.......................................
MONKEY BAR HARDWARE - NOTICE Depending on your playset model, you will have extra hardware left over. 3/8” x 3” BUTTON HD. SCREW 3/8” FLAT WASHER 3/8” T NUT 3/8” x 1-1/2” BUTTON HD.
MONKEY BAR METAL PARTS Flat Metal Bracket 2023 18-1/2" 21-1/2" Top Rung End Rung x4 2152 x5 2153 FASTENERS FOR METAL RUNGS Lock Washer x16 2-1/2" x16 1/4" 8 x3
PLAYSET ORIENTATION BACK SIDE 6' SAFETY AREA REFER TO PLAYSET INSTRUCTION MANUAL FOR SAFETY AREA LEFT SIDE RIGHT SIDE 6' SAFETY AREA FRONT SIDE TOP RAIL MONKEY BARS 1. Measure and mark hole locations of rungs. 2. Pre-drill 5/32" x 1-1/4" deep. 1" x 18-1/2" 2 x 4 x 78" 2152 x2 2154-ST x5 x10 2-1/2" Pan Head Wood Screw 1/4" Lock Washer 15" 12" 12" 12" 12" 15" Ensure holes face downward when installing ladder rungs.
MONKEY BARS END LADDER 1 x 21-1/2" 1. Measure and mark hole locations of rungs. 2153 x3 x6 2. Pre-drill 5/32" x 1-1/4" deep. 2-1/2" Pan Head Wood Screw 1/4" Lock Washer 2 x 4 x 75" x2 2155-ST 13" 13" 13" Note hole locations. Ensure holes face downward when installing ladder rungs.
ASSEMBLE END LADDER / TOP LADDER END RAIL Flat Washer Lock Washer 1-1/2” Button Head Screw T-Nut 3" Button Head Bolt TOP RAIL Lock Washer Flat Washer T-Nut T-Nut Flat Washer Lock Washer 3" Button Head Bolt 11 1-1/2” Button Head Screw Lock Washer Flat Washer
INSTALL ANGLE BRACES / BOTTOM SUPPORT Flat Washer Lock Washer 3-1/2” Hex Head Bolt (x2) T-Nut 2 x 4 x 57" 1016-ST x2 2-1/2” Hex Head Bolt (x2) Lock Washer Flat Washer 4-1/2” Hex Head Bolt (x2) T-Nut 2 x 4 x 80-1/2" 1019-ST x1 2-1/2” Hex Head Bolt Flat Washer Lock Washer T-Nut (x2) T-Nut NOTE: Counter-bore of 1019-ST toward rear side of ladder.
INSTALL POSITION TOP LADDER SUPPORTS SEE PLAYSET INSTRUCTIONS FOR CORRECT LADDER SUPPORTS. STOP RETURN TO PLAYSET INSTRUCTION MANUAL FOR THE INSTALLATION OF YOUR MONKEYBARS.
WARRANTY Backyard Play Systems warrants the following: 1. All wood and plastic (polymer) coated wood components have a Limited Lifetime Warranty. • Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unfit due solely to damage caused by fungal decay or termites. 2. All non-wood components* have a three year Limited Warranty. *Ropes carry a one year Limited Warranty. 3.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
