WS 8359 IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 © Swing-N-Slide Inc.
Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statesments and warnings reduces the likelihood of serious or fatal injury This playset has been designed for use by a maximum of twelve (12) occupants at one time having a combined weight of 1,260 pounds. This playset is intended for use by children from (2) to (10) years of age. On-site adult supervision for children of all ages is recommended.
PLAYSET MAINTENANCE Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by our warranty. To help minimize these natural defects we recommend applying a sealer or stain every two or three years, or more often as the climate dictates.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
PLAYSET SAFETY ZONE 28'-0" 14'-0" 14'-0" 6'-0" 28'-5 15/16" 16'-5 15/16" 6'-0" 6'-0" 6'-0" 6'-0" 16'-5 7/16" 30'-5 7/16" MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
TOOLS REQUIRED DRILL 1/2” & 7/16’’ SOCKETS & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SCREWDRIVER PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 1/8” DRILL BIT HELPFUL ASSEMBLY INFORMATION Your playset consists of several boxes or modules. It is important to ensure all lumber, accessories and hardware is accounted for. The following pages list the contents of each box. Use these pages to take an inventory of all parts.
(2) [PF 6010] 1’’ x 3-3/8’’ x 47-1/2’’ TOWER MODULE SA6000 / SA /SA6022 (1) [PF 6011]6081 1’’ x 3-3/8’’ x 47-1/2’’ TOWER MODULE: SA6042 BOARD LIST (4) [PF 6062] 1’’ x 3-3/8’’ x 42-1/2’’ ROOF A-FRAME (4) [PF 6164] 3’’ x 3’’ x 94’’ 6008] 3/4’’ x 5-3/8’’ x 42’’ A-FRAME BASE (2)(7) [PF[PF 6063] 3/4’’ x 3-3/8’’ x 59-5/8’’ (1) [PF 6020] 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT (3) [PF 6006] 3/4’’ x 3-3/8’’ x 44-1/2’’ (9) [PF 6013] 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCKWALL BOARD (1) [PF 6019] 2-11/16’’ x 5-3/8’’ x
TOWER MODULE SA6000 / SA 6081 /SA6022 COMPONENTS CONT.
7’’ 6’’ HARDWARE 4’’ 3 1/2’’ 3 1/4’’ 2 1/2’’ TOWER MODULE SA6000 / SA 6081 /SA6022 5/16”-18 x 6” Carriage Bolt (x3) 1/4”-20 x 1-1/4” Hex Bolt (x12) 5/16”-18 x 2-1/2” Hex Bolt (x2) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 4” Hex Bolt (x5) 5/16”-18 x 7” Hex Bolt (x1) 5/16”-18 x 8-1/2” Hex Bolt (x1) 1/4’’ Washer (x16) 5/16” Washer (x24) 5/16” Loc Nut (x9) 5/16’’ Loc Washer (x12) #12 x 3/4” Truss Screw (x14) 5/16” Wood Loc Washer (x3) 3/16” Tarp Washer (x7)
(10) [PF 6000] 5/8’’ x 5-3/8’’ x 33-3/4’’ /16’’ x 3’’ x 62’’ A-FRAME SUPPORT TERRACE MODULE SA6001 / SA 6031 x2 (4) [PF 6001] 5/8’’ x 5-3/8’’ BOARD LISTx 9-1/4’’ TERRACE MODULE: SA6001 (2) [PF 6060] 5/8’’ x 5-3/8’’ x 13’’ SUN ’’ x 3-3/8’’ x 83’’ A-FRAME LEGS ’’ x 3-3/8’’ x 60’’ ROCKWALL SUPPORT 8’’ x 3-3/8’’ x 58’’ A-FRAME SUPPORT (1) [PF 6061] 1-1/2’’ x 1-1/2’’ x 40’’ (2) [PF 6028] 1-3/8’’ x 3’’ x 79’’ 8’’ x 3-3/8’’ x 43-1/2’’ 8’’ x 3-3/8’’ x 17-1/4’’ SLIDE STAKE 8’’ x 3-3/8’’ x 15-1/2’’ DECK SUPP
(5) [PF 6005] 3/4’’ x 3-3/8’’ x 42’’ (1) [PF 6034] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-L (2) [PF 6003] 3/4’’ x 3-3/8’’ x 35-7/8’’ (1) [PF 6035] 1-3/8’’ x 3-3/8’’ x 66-1/4’’ LADDER SUPPORT-R LADDER MODULE SA6004 (2) [PF 6058] 5/8’’ x 3-3/8’’ x 30’’ BOARD LIST (2) [PF 6002] 3/4’’ x 3-3/8’’ x 22-1/2’’ (1) [PF 6029] 5/8’’ x 3-3/8’’ x 20-1/2‘’ PICNIC TABLE MODULE SA6018 (5) [PF 6032] 1’’ x 3-3/8’’ x 18-1/2’’ BOARD LIST PICNIC TABLE MODULE: SA6018 LADDER (4)MODULE: [PF 6172] 5/8’’ x 3-3/8’’ x 11-1/2’
TURBO TUBE SLIDE Five Foot Turbo Slide (x1) BOARD LIST (2) [PF 6144] 1-3/8’’ x 3-3/8’’ x 47-1/2’’ (1) [PF 6143] 1-3/8’’ x 3-3/8’’ x 46’’ (1) [PF 6142] 1-3/8’’ x 3-3/8’’ x 30-5/8’’ (1) [PF 6141] 1-3/8’’ x 3-3/8’’ x 24-5/8’’ (1) [PF 6140] 1-3/8’’ x 3-3/8’’ x 23-5/8’’ (3) [PF 6138] 1-3/8’’ x 3-3/8’’ x 18’’ (1) [PF 6136] 1-3/8’’ x 3-3/8’’ x 11-1/4’’ (2) [PF 6145] 1-3/8’’ x 3-3/8’’ x 8-3/8’’ (1) [PF 6137] 1-3/8’’ x 3-3/8’’ x 13’’ (1) [PF 6146] 1-3/8’’ x 3-3/8’’ x 8-1/4’’ (1) [PF 6178] 1-3/8’’ x 2-5/8’’ x 23-
STEP 1 6’’ Flush 6’’ PF 6164 3’’ x 3’’ x 94’’ (3) 2-1/2’’ Screws 0 01 F6 P ’’ -3/8 3 1’’ x ’’ 1/2 7x4 T-Nut Small (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’ Washer 5/16’’Loc-Washer 59-1/4’’ P ’’ -3/8 x3 /4’’ 63 00 F6 ’’ 1/2 4x4 FRAME A 831 830 2 /8’’ 5 59x ’ ’ -3/8 E x3 ’ AS ’ 4 3/ EB 3 M 606 -FRA A PF (3) 2-1/2’’ Screws PF 6164 3’’ x 3’’ x 94’’ 47-1/2’’ (2) 2-1/2’’ Screws 2-1/2” Deck Screw (x14) 1-1/2’’ ALL JOINTS 829 1. Assemble Frame A as shown above.
STEP 2 6’’ Flush /8’’ 3-3 SE x ’ A ’ 3/4 ME B 3 6 RA 60 A-F PF (3) 2-1/2’’ Screws PF 6164 3’’ x 3’’ x 94’’ 6’’ ’’ 01 01 F6 P /8’’ -3 x3 ’’ 5/8 9x5 (3) 2-1/2’’ Screws PF 6164 3’’ x 3’’ x 94’’ 47-1/2’’ ’’ 1/2 7x4 T-Nut Small (2) 2-1/2’’ Screws PF 6 600 ’’ 3/4 /8’’ -3 x3 5/16-18 X 4’’ Hex Head Bolt /2’’ 5/16’’ Washer 1 4x4 (2) 2-1/2’’ Screws 5/16’’Loc-Washer (2) 2-1/2’’ Screws 59-1/4’’ ’’ 6 600 44-1/2 F P ’’ x -3/8 3 4’’ x 31’’ 3/ FRAME B (2) 2-1/2’’ Screws Hint!! Use p
STEP 3 PF 600 53 /4’’ x3 -3/8 (3) 2-1/2’’ Screws Check to make sure structure is square PF 600 53 /4’’ 600 43 -3/8 /4’’ ’’ x PF x3 -3/8 ’’ x 600 43 /4’’ x3 -3/8 600 53 NOTE: /4’’ x3 /4’’ x3 Board mounts to inside of upright. -3/8 ’’ x 42’ ’ (2) 2-1/2’’ Screws Flush PF 53 ’’ x 42’ ’ (2) 2-1/2’’ Screws 600 (3) 2-1/2’’ Screws 42’ ’ 59-1/4’’ PF 42’ ’ Flush x3 (3) 2-1/2’’ Screws PF ’’ x 42’ ’ (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x16) 1.
STEP 4 (3) 2-1/2’’ Screws Check to make sure structure is square (2) 2-1/2’’ Screws (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws (3) 2-1/2’’ Screws FRAME B NOTE: Board mounts to inside of upright. (3) 2-1/2’’ Screws FRAME A 2-1/2” Deck Screw (x16) 1. Attach Frame A to Frame B as shown.
STEP 5 (3) 1-3/4’’ Screws Per Board Flush (2) PF 6149 1-3/8’’ x 3-3/8’’ x 15-1/2’’ DECK SUPPORT Flush 1 (3) 1-3/4’’ Screw per joint 0 (4) 3’’ Screw NOTE: PRE-DRILLED HOLES 9 8 1 7 1-3/4” Deck Screw (x6) 3” Deck Screw (x4) 0 6 9 8 1. Install Deck Supports as shown.
STEP 6 PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (6) 1-3/4’’ Screws (2) 2-1/2’’ Screws (6) 1-3/4’’ Screws PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6011 1’’ x 3/8’’ x 47-1/2’’ 16-1/2’’ 16-1/2’’ PF 6011 1’’ x 3/8’’ x 47-1/2’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ PF 6003 3/4’’ x 3-3/8’’ x 35-7/8’’ (2) 2-1/2’’ Screws FS2831 3 FS2830 2-1/2 FS2829 2 FS2831 FS2828 3 1-3/4 1-3/4” Deck Screw (x12) TOP VIEW FS2830 FS2827 2-1/2 1-5/8 2-1/2” Deck Screw (x4) 1. Install Deck Boards as shown.
STEP 7 (7) PF 6008 3/4’’ x 5-3/8’’ x 42’’ (6) 1-3/4’’ Screws per board 1 0 9 8 7 6 1-3/4” Deck Screw (x42) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 3/8’’.
STEP 8 Check to make sure structure is square PF 602 61 ’’ x 3-3 /8’’ PF x4 2’’ 602 61 ’’ x 3-3 /8’’ x4 2’’ 47-1/4’’ FRAME A (2) 2-1/2’’ Screws 5/16-18 X 4’’ Hex Head Bolt 5/16’’Loc-Washer 5/16’’ Washer 1 T-Nut Small Hint!! Use parts from your Terrace Boxes. 2-1/2” Deck Screw (x8) 1. Install Deck Support Board as shown.
STEP 9 (3) 2’’ Screws PF 600 53 Check to make sure structure is square x2 /4’’ x3 -3/8 ’’ x 42’ ’ (3) 2’’ Screws 602 61 ’’ x 3-3 /8’’ x4 2’’ PF 6028 1-3/8’’ x 3’’ x 79’’ PF 6028 1-3/8’’ x 3’’ x 79’’ PF Flush 5/16-18 X 2’’ Hex Head Bolt 5/16’’Loc-Washer (3) 2’’ Screws 5/16’’ Washer PF (2) 2’’ Screws 600 53 T-Nut Small /4’’ x3 -3/8 ’’ x 47-1/4’’ 42’ ’ (3) 2’’ Screws Flush FRAME C AND D FS2831 3 FS2830 2-1/2 FS2829 2 FS2828 1-3/4 1. Assemble Frames C and D as shown.
STEP 10 Flush With Outside Face of 1-3/8’’ x 3’’ Flush With Outside Face of 1-3/8’’ x 3’’ Flush With Top of Frame (2) 2-1/2’’ Screws PF 602 53 Flush With Top of Frame /4’’ x3 -3/8 ’’ x 2 Check to make sure structure is square 9-1 /4’’ 3/4 ’’ x PF 60 3-3 /8’’ 25 x2 9-1 (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws /4’’ PF 602 53 /4’’ x3 -3/8 ’’ x 2 Flush With Outside Face of 1-3/8’’ x 3’’ 9-1 /4’’ 50-5/8’’ (2) 2-1/2’’ Screws 3/4 ’’ x PF 60 3-3 /8’’ 24 x2 7- Flush With Outside Face o
STEP 11 Flush With Outside Face of 1-3/8’’ x 3’’ (2) 2-1/2’’ Screws Check to make sure structure is square 025 6 PF ’’ -3/8 x3 /4’’ 3 ’’ 1/4 9x2 Flush With Top of Frame (2) 2-1/2’’ Screws PF 5 602 50-5/8’’ ’’ 3/4 /8’’ -3 x3 /4’’ 3 5 /4’’ 602 29-1 F P 8’’ x -3/ x3 ’’ Flush With Outside Face of 1-3/8’’ x 3’’ (2) 2-1/2’’ Screws 4 /4’’ 602 27-3 F x P 8’’ / 3-3 x ’ ’ 4 / Flush With Outside Face of 1-3/8’’ x 3’’ 3 FRAME D 7 P 2” Deck Screw (x10) 1. Assemble Frame D as shown.
STEP 12 Check to make sure structure is square (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws (3) 2-1/2’’ Screws 79’’ (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws FRAME D FS2831 3 (2) 2-1/2’’ Screws FRAME C FS2830 2-1/2 FS2829 2 1. Attach Frame C Frame D to Tower as shown.
STEP 13 PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ 10-5/8’’ Check to make sure structure is square 10-5/8’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ TOP VIEW (2) 1-3/4’’ Screws PF 6061 1-1/2’’ x 1-1/2’’ x 40’’ PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws (1) 1-3/4’’ Screws (1) 1-3/4’’ Screws PF 6150 3/4’’ x 3-3/8’’ x 24-3/4’’ (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws (2) 1-3/4’’ Screws PF 6061 1-1/2’’ x 1-1/2’’
STEP 14 (6) PF 6135 3/4’’ x 5-3/8’’ x 26-1/4’’ Note: Holes 1-7/8’’ From Edge on This Side (6) PF 6135 3/4’’ x 5-3/8’’ x 26-1/4’’ (6) 1-3/4’’ Screws per board (6) 1-3/4’’ Screws per board All Boards Flush Note: Holes 1-7/8’’ From Edge on This Side 1 0 9 7 1-3/4” Deck Screw (x72) 1. Install Deck Boards as shown. NOTE: Standard gap between deck boards is 7/16’’.
STEP 15 PF 6005 3/4’’ x 3-3/8’’ x 42’’ (6) 2-1/2’’ Screws 53-7/8’’ PF 6005 3/4’’ x 3-3/8’’ x 42’’ (6) 2-1/2’’ Screws 2-1/2” Deck Screw (x12) 1. Attach Gap Filler Boards as shown.
STEP 16 PF 6022 3/4’’ x 3-3/8’’ x 19-1/2’’ (3) 2’’ Screws 50-5/8’’ PF 6022 3/4’’ x 3-3/8’’ x 19-1/2’’ (3) 2’’ Screws 50-5/8’’ PF 6005 3/4’’ x 3-3/8’’ x 42’’ 1 0 9 8 7 2” Deck Screw (x12) 1. Install Barrier Support Boards as shown.
STEP 17 2-7/8’’ (2) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ (4) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws #12 x 3/4” Pan Screw (x4) INSIDE VIEW 30mm Deck Screw (x8) 1. Install Barrier Boards as shown.
STEP 18 (2) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ 2-7/8’’ (4) 30mm Screws per board Panel Bracket (4) 3/4’’ Pan Screws INSIDE VIEW #12 x 3/4” Pan Screw (x8) 30mm Deck Screw (x8) 1. Install Barrier Boards as shown.
STEP 19 PF 6007 3/4’’ x 3-3/8’’ x 47-1/2’’ (3) 2-1/2’’ Screws (2) PF 6025 3/4’’ x 3-3/8’’ x 29-1/4’’ (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws (3) 2-1/2’’ Screws PF 6023 3/4’’ x 3-3/8’’ x 22-1/2’’ 62-5/8’’ (3) 2-1/2’’ Screws FS2831 3 FS2830 2-1/2 1. Attach Barrier Support Boards as shown.
STEP 20 1’’ 3-1/8’’ 3-1/8’’ 1’’ 1-5/8’’ PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ 1/2’’ GAP PRE-DRILL (4) 1/8’’ HOLES 1/2’’ GAP PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ 4-7/8’’ FS2831 3 FS2830 2-1/2 PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 17-3/8’’ (4) 30mm Screws per board PF 6172 5/8’’ x 3-3/8’’ x 11-1/2’’ FS2829 2 FS2828 1-3/4 (10) 3/4’’ Screws per Window Frame PF 6001 5/8’’ x 5-3/8’’ x 9-1/4’’ FS2827 2-13/16’’ 1-5/8 2-13/16’’ FS2826
STEP 21 (6) PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 1-1/4’’ 1-1/4’’ GAPS BETWEEN BOARDS (4) 30mm Screws per board 2-1/8’’ (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ 2-1/8’’ GAPS BETWEEN BOARDS (4) 30mm Screws per board (2) 30mm Screws per board (4) 3/4’’ Pan Screws INSIDE VIEW 30mm Deck Screw (x48) #12 x 3/4” Pan Screw (x4) 1. Install Barrier Boards as shown.
STEP 22 (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ 2-1/8’’ GAPS BETWEEN BOARDS 2-1/8’’ (4) 30mm Screws per board (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ 2-1/8’’ GAPS BETWEEN BOARDS (4) 30mm Screws per board 2-1/8’’ 30mm Deck Screw (x24) 1. Attach Barrier Boards as shown.
STEP 23 (3) 2-1/2’’ Screws PF 6144 1-3/8’’ x 3-3/8’’ x 47-1/2’’ (3) 2-1/2’’ Screws 62-5/8’’ (3) 2-1/2’’ Screws PF 6144 1-3/8’’ x 3-3/8’’ x 47-1/2’’ 31’’ (3) 2-1/2’’ Screws (2) 2-1/2’’ Screws Flush PF 6143 1-3/8’’ x 3-3/8’’ x 46’’ (3) 2-1/2’’ Screws 1 Hint!! Use parts from your Tube Slide. 2-1/2” Deck Screw (x17) 1. Attach Slide Support Board as shown.
STEP 24 (2) PF 6000 5/8’’ x 5-3/8’’ x 33-3/4’’ 1-1/4’’ GAPS BETWEEN BOARDS PF 6142 1-3/8’’ x 3-3/8’’ x 30-5/8’’ (4) 30mm Screws per board (6) 2-1/2’’ Screws 1-1/4’’ 23-5/8’’ 1 0 9 8 2-1/2” Deck Screw (x6) 30mm Deck Screw (x8) 1. Attach Slide Barrier Board as shown.
STEP 25 PF 6140 1-3/8’’ x 3-3/8’’ x 23-5/8’’ (6) 2-1/2’’ Screws PF 6178 1-3/8’’ x 2-5/8’’ x 23-5/8’’ (5) 2-1/2’’ Screws FLUSH WITH INSIDE OF POST PF 6146 1-3/8’’ x 3-3/8’’ x 8-1/4’’ (4) 2-1/2’’ Screws PF 6181 5/8’’ x 3-1/4’’ x 3-3/8’’ ’’ 5/8 23- PF 6141 1-3/8’’ x 3-3/8’’ x 24-5/8’’ (6) 2-1/2’’ Screws 1 2-1/2” Deck Screw (x27) 1. Attach Slide Support Board as shown.
STEP 26 Flush (2) 2-1/2’’ Screws 31’’ Flush (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws PF 6024 3/4’’ x 3-3/8’’ x 27-3/4’’ (2) 2-1/2’’ Screws PF 6024 3/4’’ x 3-3/8’’ x 27-3/4’’ 2’’ (4) 30mm Screws per board 1-5/8’’ 2’’ GAPS BETWEEN BOARDS (3) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ (4) 30mm Screws per board (4) PF 6021 5/8’’ x 5-3/8’’ x 30-3/4’’ NO GAPS BETWEEN BOARDS 30mm Deck Screw (x28) 2-1/2” Deck Screw (x8) 1. Install Barrier Support Board as shown. 2. Install Barrier Boards as shown.
STEP 27 PF 6020 3’’ x 3’’ x 47-1/2’’ SWING BEAM SUPPORT TOP OF BEAM SUPPORT 84-1/2’’ FROM BOTTOM OF POST Loc Nut 5/16’’ Washer Wood Loc-Washer 5/16-18 X 6’’ Carriage Bolt 1. Install Swing beam support as shown.
STEP 28 PF 6019 2-11/16’’x5-3/8’’x93’’ Swing Beam 5/16’’ T-Nut Large 5-1/2’’ Swing Hanger Beam Clamp 2 1 FS2831 3 3 FS2830 2-1/2 x4 FS2829 2 FS2828 1-3/4 Correct Orientation 4 FS2827 1-5/8 (4) 1-1/4’’ Deck Screws 5 FS2826 1-1/4 FS2826 3/4 1-1/4” Deck Screw (x24) 1. Attach Swing Hanger(s) to swing beam as shown. NOTE: Make certain hanger and plate are snug against the bottom of the swing beam, (Fig 5), before installing screws.
STEP 29 PF 6018 2-11/16’’x3’’x62’’ A-Frame SB Support 5/16”-18 x 7” Hex Head Bolt (1) 3’’ Screws (1) 3’’ Screws 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 6017 1-3/8’’x3-3/8’’x83’’ A-Frame 5/16”-18 x 2-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 5/16” Washer 5/16” Loc Washer (2) 2-1/2’’ Screws 5/16”-18 x 4” Hex Head Bolt (2) 2-1/2’’ Screws (2) 2-1/2’’ Screws 5/16-18 T-Nut Small PF 6016 1-3/8’’x3-3/8’’x58’’ A-Frame Support 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut
STEP 30 (2) Swing Beam Bracket 5/16”-18 x 3-1/2” Hex Head Bolt x2 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/2” Hex Head Bolt 5/16” Washer x2 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
STEP 31 Beam Brace 5/16”-18 x 3 1/4” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16-18 T-Nut Small 1. Install Swing Beam Brace as shown.
STEP 32 5/16”-18 x 6” Carriage Bolt 5/16”-18 x 8-1/2” Hex Head Bolt 5/16” Loc Washer 5/16” Washer 5/16” Wood Loc Washer 5/16” Washer 5/16” Loc Nut 1. Install Swing Beam as shown.
STEP 33 (1) 3’’ Deck Screws 1-5/8’’ 1-5/8’’ 13-1/2’’ PF RA F ’’ x PF 1 62 3- ’’ 3/8 2 x4 OO R ’’ /2 -1 FA ME 60 PF 6058 5/8’’ x 3-3/8’’ x 30’’ (4) 30mm Deck Screws Check to make sure structure is square 60 62 1’’ x3 -3 /8’ ’x 42 -1 /2’ ’R OO FA -F RA ME x2 3/4’’ CENTERED PF 6060 5/8’’ x 5-3/8’’ x 13’’ SUN (4) 30mm Screws 3” Deck Screw (x2) x2 1. Assemble Roof A-Frames as shown.
STEP 34 (10) 30mm Screws (1) PF 6056 5/8’’ x 2’’ x 10’’ (2) PF 6059 5/8’’ x 2’’ x 7’’ x2 Note: Place screws through A-Frame and into end of PF 6053 CENTERED Note: PF 6053 Rests on Top of PF 6056 (2) 2-1/2’’ Screws 2’’ / 3-1 4 PF 6053 1-3/8’’ x 3-3/8’’ x 43-1/2’’ SIDE VIEW (2) 2-1/2’’ Screws Note: Place screws through A-Frame and into end of PF 6053 2’’ / 3-1 4 FS2831 3 FS2830 2-1/2 30mm Deck Screw (x20) 1. Assemble the Roof frame as shown.
STEP 35 3/4’’ Offset Each Side (3) 1-5/8’’ Screws Side View (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws (3) 1-5/8’’ Screws 1-5/8” Deck Screw (x12) 1. Attach Roof Frame to Tower as shown.
STEP 36 (4) 2’’ Screws PF PF 605 03 /4’’ x3 -3/8 ’’ x 43- 1/2 ’’ 0 8 7 03 /4’’ x3 -3/8 ’’ x 4 3-1 /2’’ (4) 2’’ Screws 1 9 605 2” Deck Screw (x8) 1. Attach Roof Side Support Boards as shown.
STEP 37 (3) 3/4’’ Screws (3) 3/16’’ Tarp Washer 3/4” Pan Head Screw (x6) 1. Attach Tarp as shown.
STEP 38 x -3/8’’ 030 1 PF 6 ’’ 3-3/8 x 52- 3/4’’ RT-R x 52- PPO ’’ 3-3/8 U ER S LADD 3/4’’ x -3/8’’ 031 1 PF 6 LADD -L ORT UPP ER S (2) 2-1/2’’ Screws per Rung (4) PF 6032 1’’ x 3-3/8’’ x 18-1/2’’ (2) 2-1/2’’ Screws per Rung PF 6029 5/8’’ x 3-3/8’’ x 20-1/2‘’ FLUSH Hint!! Use parts from your Ladder Box. 2-1/2” Deck Screw (x20) 1. Assembly Ladder as shown.
STEP 39 (3) 2-1/2’’ Screws Panel Bracket (4) 3/4’’ Pan Screw UNDERSIDE VIEW 2-1/2” Deck Screw (x3) #12 x 3/4” Pan Screw (x4) 1. Attach Ladder to Tower as shown.
STEP 40 ALIGN SCREWS WITH PRE DRILLS (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCK WALL BOARD (6) PF 6389 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCK WALL BOARD (1) PF 6013 5/8’’ x 5-3/8’’ x 22-3/4’’ ROCK WALL BOARD 2” Deck Screw (x32) 1. Align and install rock wall boards to the image above.
STEP 41 (3) 2-1/2’’ Screws per side 1 0 9 8 Under Deck View 2-1/2” Deck Screw (x6) 1. Attach Rock Wall as shown.
STEP 42 (2) 1/4’’ T-Nuts (2) 1-1/4’’ Hex Head Bolts (2) 1/4’’ Flat Washer Per Rock (2) 1/4’’ Loc-Washer Per Rock 1. Attach Climbing Rocks as shown.
STEP 43 (2) PF 6039 3/4’’ x 3-3/8’’ x 9-3/4’’ TABLE SUPPORT 3’’ (4) 1-1/4’’ Deck Screws 2-3/8’’ (2) PF 6037 3/4’’ x 3-3/8’’ x 15-3/4’’ BENCH SUPPORT OUTSIDE FACE TO OUTSIDE FACE 3’’ 11-1/4’’ (4) 1-1/4’’ Deck Screws 6-7/8’’ 2-3/8’’ (4) 2’’ Screws (2) PF 6133 3/4’’ x 3-3/8’’ x 41-1/2’’ TABLE (4) 2’’ Screws (2) 2’’ Screws OUTSIDE FACE TO OUTSIDE FACE 6-7/8’’ (2) 2’’ Screws 36’ ’ (2) PF 6038 1’’ x 3-3/8’’ x 26-7/8’’ PICNIC TABLE LEG PF 6040 1’’ x 5-3/8’’ x 41-1/2’’ BENCH FS2831 3 Check to
STEP 44 PF 6023 3/4’’ x 3-3/8’’ x 22-1/2’’ (4) 1-5/8’’ Screws From Behind Deck Support Flush to Support Flush to Upright Underdeck View (3) 1’’ Truss Screws Grade FS2831 3 2” (2) 30mm Deck Screws FS2830 2-1/2 FS2829 2 PF 6009 1-3/8’’x3-3/8’’x17-1/4’’ Slide Stake FS2828 1-3/4 FS2827 1-5/8 30mm Deck Screw (x8) 1” Truss Screw (x3) 1-5/8” Deck Screw (x4) FS2826 1. Attach Slide Support Boards and Slide as shown.
STEP 45 NOTE: Attach secondary handles at desired location 1/4” Washer 11” to the top of the handle. 1/4’’ x 1-3/4” Pan Screw Back View 1-3/4” Pan Screw (x2) 1. Attach Safety Handle and I.D. Tag as shown.
STEP 46 Wind Rider 2 1 Loc-Nut 3 51” Un-Coated chain 5/16’’ Flat Washer QuickLink 5/16’’ Flat Washer 5/16”-18 x 6-1/2” Hex Bolt QuickLink Wind-Rider 4 Wind Rider Assembly 1. Insert Seat into Handle as shown in (Step1). Secure in place with hardware shown. Note: Make certain no more than two bolt threads protrude from the Loc-Nut once fully tightened. 2. Insert (1) Quick Link into the end of each length of chain, as shown in (Step 2). Make certain the Quick Link is positioned as shown. 3.
Swing Seat Assembly BOTTOM OF SEAT LOGO ON TOP BOTTOM OF SEAT PLASTIC COATED END LOGO ON TOP STEP 47 1. Take one length of chain and place the outermost link of coated chain through the Quick Link as shown. 2. Place the Quick Link through the Grommet of the swing seat as shown. 3. Tighten the threaded sleeve of the Quick Link with a suitably sized wrench so that the seat is securely attached and the Quick Link cannot be easily loosened. Repeat for second chain, Quick Link and Swing Seat Grommet. 4.
STEP 48 1. Install Turbo Tube Slide as shown. NOTE: Turbo Tube Slide assembly detailed in instructions included with accessory.
STEP 49 PF 6136 1-3/8’’ x 3-3/8’’ x 11-1/4’’ PF 6145 1-3/8’’ x 3-3/8’’ x 8-3/8’’ (4) 2-1/2’’ Screws PF 6138 1-3/8’’ x 3-3/8’’ x 18’’ (9) 2-1/2’’ Screws PF 6145 1-3/8’’ x 3-3/8’’ x 8-3/8’’ (4) 2-1/2’’ Screws PF 6138 1-3/8’’ x 3-3/8’’ x 18’’ PF 6138 1-3/8’’ x 3-3/8’’ x 18’’ (9) 2-1/2’’ Screws 31 Underdeck View 0 9 8 2-1/2” Deck Screw (x26) 1. Assemble and attach Slide Footer to Turbo Tube Slide as shown.
STEP 50 5/16” Washer Fold up Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 1. Place swing set in final location and mount Anchor-It(s) at locations circled above. 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY WARRANTY REGISTRATION: Please complete your warranty registration to properly validate your product warranty. Register your product online at: www.OnlineWarranty.net Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment to providing quality residential playground products.
PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration Benefits of registering online: ■ Quick & simple from home or mobile ■ Record your purchase in our system ■ Initiate product warranty ■ Improved customer support ■ Notification of new product information Register your product online at www.OnlineWarranty.
