PB 8360 READY TO ASSEMBLE LDR 03-22-2019 LA 9170
5CHGV[ %JGEMNKUV HQT 5YKPIÄ0Ä5NKFG 2NC[ 5GVU CPF #EEGUUQTKGU 1DUGTXKPI VJG HQNNQYKPI UVCVGUOGPVU CPF YCTPKPIU TGFWEGU VJG NKMGNKJQQF QH UGTKQWU QT HCVCN KPLWT[ three 6JKU RNC[UGV JCU DGGP FGUKIPGF HQT WUG D[ C OCZKOWO QH GKIJV QEEWRCPVU CV QPG VKOG JCXKPI C EQODKPGF YGKIJV QH RQWPFU 345 pounds and maximum 115 pounds on each swing.
PLAYSET MAINTENANCE Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by our warranty. To help minimize these natural defects we recommend applying a sealer or stain every two or three years, or more often as the climate dictates.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
MAXIMUM OF 115 lbs.
TOOLS REQUIRED INCLUDED HARDWARE 3/8" X 3-3/4" HEX BOLT (x 4) 1/4" LOCK WASHER (x 4) 3/8" FLAT WASHER (x 24) 3/8" X 3-3/4" CARRIAGE BOLT (x 4) 3/8" LOCK WASHER (x 8) 3/8" X 3-1/4" CARRIAGE BOLT (x 12) QUICK CLIP (x 4) 3/8" X 3" LAG SCREW (x 2) 3/8" LOCK NUT (x 16) 1/4" X 2-1/2" PAN HEAD SCREW (x 4) SPRING CLIP (x 2) #8 X 2-1/2" WOOD SCREW (x 8) 6 3/8" T-NUT (x 4)
COMPONENTS PF 6090 2-3/8 X 5-1/8 X 87-1/2" SWING BEAM (x1) PF 6091 2-3/8 X 3 X 87-1/2" LEG (x4) PF 6092 3/4" X 3-3/8" X 68" A-BRACE (x2) 2447R ANGLED BRACKET RIGHT (x2) SA 1699 PLAYSET PLAQUE (x1) HARDWARE INCLUDED 2449 L-BRACKET (x2) SA 4294 SAFETY PLATE (x1) HARDWARE INCLUDED 48" COATED CHAIN (x4) 2448L ANGLED BRACKET LEFT (x2) 2434 SWING (x2) WS 4425 SWING HANGER (x6) 2096 TRAPEZE (x1) 24" COATED CHAIN (x2) ANCHOR-IT STRAP (x4) ANCHOR-IT (x4) PF 1574 CAP & HARDWARE (x6) 7 INSTRUCTIONS BOOK
STEP 1: A-BRACE 3/8" X 3-3/4" HEX BOLT X 2 3/8" LOCK WASHER X 2 3/8" FLAT WASHER X 2 PF 6091 X 2 SWING LEG PF 6092 X 1 A-BRACE 3/8" T-NUT X 2 NOTE HOLE LOCATIONS. YOU WILL ASSEMBLE TWO A-FRAME POST ASSEMBLIES. 1. MOVE POSTS APART AND LOCATE AND ATTACH A-BRACE INTO PRE-DRILLED HOLES. DO NOT FULLY TIGHTEN BOLTS AT THIS TIME.
STEP 2: L-BRACKET 3/8" X 3-3/4" CARRIAGE BOLT X 2 PF 6091 SWING LEG 2449 X 1 L-BRACKET SUPPORT HINT: USE SWING BEAM. 3/8" FLAT WASHER X 2 3/8" LOCK NUT X 2 1. USE A TEMPORARY SUPPORT UNDER ENDS AND CAREFULLY SWING POST TOGETHER UNTIL EDGES TOUCH. . DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME.
STEP 3: A-FRAME ANGLED BRACKETS 2448 X 1 ANGLED BRACKET 2447 X 1 ANGLED BRACKET 3/8" X 3-1/4" CARRIAGE BOLT X 4 3/8" FLAT WASHER X 4 3/8" LOCK NUT X 4 YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. 1. ATTACH ANGLED BRACKETS ON A-FRAME ASSEMBLIES. DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME.
STEP 4: SWING HANGERS #6 X 1-1/4" WOOD SCREW X 12 PF 1574 X 6 CAP 3/8" LOCK NUT X 6 1-3/8" FLAT WASHER X 6 3/8" FLAT WASHER X 6 WS 4425 X 6 SWING HANGER HOLD POSITION OF SWING HANGER WHILE TIGHTENING LOCK NUT. PF 6090 X 1 SWING BEAM NOTE: ORIENT BEAM SO 1/4" PRE-DRILLED HOLES ARE AT BOTTOM BEFORE INSTALLING SWING HANGERS. FINAL POSITION OF EACH SPRING CLIP IS PERPENDICULAR TO SWING BEAM. 1. NOTE: 1/4" PRE-DRILLED HOLES LOCATIONS. 2. INSTALL SWING HANGERS TO SWING BEAM. 3.
STEP 5: SWING BEAM ASSEMBLY YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. 3/8" LOCK NUT X 2 3/8" FLAT WASHER X 2 3/8" X 3-1/4" CARRIAGE BOLT X 2 1. POSITION SWING BEAM ASSEMBLY RESTING UPON ONE A-FRAME ONLY. 2. ALIGN HOLES AND INSERT CARRIAGE BOLTS. DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME.
STEP 6: SWING BEAM ASSEMBLY 3/8" FLAT WASHER X 1 3/8' LOCK NUT X 1 YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. 3/8 X 3-1/4" CARRIAGE BOLT X 1 1. LAY A-FRAME ON THE GROUND WITH ANGLED BRACKETS FACING UP. 2. POSITION SWING BEAM ASSEMBLY RESTING UPON A-FRAME. 3. ALIGN HOLES AND INSERT CARRIAGE BOLT. DO NOT FULLY TIGHTEN CARRIAGE BOLT AT THIS TIME.
STEP 7: LIFTING SWINGSET SWING A-FRAME UP. 3/8" FLAT WASHER X 1 3/8" X 3-1/4" CARRIAGE BOLT X 1 1. SWING A-FRAME UP AND INSERT SECOND BOLT. DO NOT FULLY TIGHTEN CARRIAGE BOLT AT THIS TIME.
STEP 8: FINAL POSITION 104" 134 -1/2" TIGHTEN ALL LOCK NUTS UNTIL 2 THREADS MINIMUM EXTEND PAST NUT. 1. MOVE PLAYSET INTO ITS FINAL POSITION. MAKE SURE PLAYSET IS SQUARE. 2. FULLY TIGHTEN ALL FASTENERS AT THIS TIME. ENSURE TWO THREADS MINIMUM PROTRUDE PAST LOCK NUTS.
STEP 9: SECURING L-BRACKETS 3/8" FLAT WASHER X 2 3/8" LOCK WASHER X 2 3/8" X 3" LAG BOLT X 2 1. PLACE A LAG IN PRE-DRILLED HOLES AND TIGHTEN.
STEP 10: SECURING PLAYSET PRE-DRILL 1/8" X 2" DEEP. 1/4" X 2-1/2" PAN HEAD SCREWS X4 1/4" LOCK WASHER X 4 #8 X 2-1/2" WOOD SCREWS X 8 1. SECURE PLAYSET WITH WOOD SCREWS AS SHOWN.
STEP 11: TRAPEZE ASSEMBLY FIG. 11.1 24" CHAIN GREEN COATING DOWN. FIG. 11.2 2096 X 1 TRAPEZE FIG. 11.3 1. ATTACH CHAIN TO SPRING CLIP FIRST, POSITION AT TOP OF CLIP. (FIG 11.1) 2. ATTACH SPRING CLIP TO TRAPEZE. (FIG. 11.2) 3. CLOSE AND TIGHTEN SPRING CLIP. LOCK WITH PLIERS. (FIG. 11.
STEP 12: SWING ASSEMBLY PLASTIC COATED END. QUICK CLIP X 4 FIG. 12.1 FACE NUT TOWARDS UNDERSIDE OF SWING. 48" CHAIN GREEN COATING DOWN. FIG. 12.2 FULLY TIGHTEN WITH PLIERS. FIG. 12.3 2434 X 2 SWING 1. ATTACH CHAIN TO QUICK CLIP FIRST, POSITION AT TOP OF LINK AS SHOWN. (FIG. 12.1) 2. PLACE THE QUICK CLIP THROUGH THE GROMMET OF THE SWING. (FIG 12.2) 3. FULLY TIGHTEN THE THREADED SLEEVE OF THE QUICK CLIP WITH PLIERS. (FIG. 12.3) 4. REPEAT FOR SECOND CHAIN, QUICK CLIP AND SWING.
STEP 13: HANGING SWING FIG. 13.1 INSERT CHAIN DIRECTLY INTO SWING HANGER. UNCOATED END OF CHAIN. FIG. 13.2 SA 4294 X 1 SAFETY PLA TE SA 1699 X 1 PLAYSET PLAQUE 2096 X 1 TRAPEZE 56" 48" 2434 SWING 53" MAX ADJUST CHAINS AT TOP. 2434 SWING 8" MINIMUM WHEN OCCUPIED ADJUST CHAINS AT TOP. 1. ATTACH THE SWINGS AND TRAPEZE CHAINS TO THE SPRING CLIPS ON THE SWING HANGERS AS SHOWN. (FIG. 13.1) 2. ATTACH PLAYSET PLAQUE AND SAFETY PLATE TO SET AS INDICATED WITH SCREWS PROVIDED AS SHOWN. (FIG 13.
STEP 14: ANCHOR-IT 1. AT LOCATIONS CIRCLED ABOVE, TWIST THE ANCHOR-IT INTO THE GROUND UNTIL ONLY THE LOOP IS EXPOSED. 2. PLACE ANCHOR-IT STRAP THROUGH, FOLD THE ENDS TOGETHER AND ATTACH TO THE UNIT AS SHOWN. NOTE: KEEP AS LITTLE PLAY AS POSSIBLE USING ANY OF THE HOLES IN THE STRAP THAT WORK BEST.
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY IMPORTANT Keep your proof of purchase and receipt. Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty SURYLGHV FRQ¿GHQFH DQG GHPRQVWUDWHV RXU FRPPLWPHQW WR providing quality residential playground products.
Got Questions? We’ve got answers! Call our Customer Support Representatives 1-800-888-1232 Available Monday - Friday, 7am - 5pm (CST) Technical support from experienced Swing-N-Slide customer service representatives who have actually built a swing set themselves. © Swing-N-Slide Inc.
