2692-RF - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information Call our toll-free number: 1-866-437-0784 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST or email: customerservice@backyard-play.
(This page intentionally left blank.
2692-RF Backyard Play Systems Customer Service 1-866-890-2211 1000 Ternes Drive Monroe, MI 48162 Tools Required Playset First... Adult Assistance required Squareness is very Important! Hammer Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin. If you have purchased accessories to accompany this play set, please read all installation instructions before beginning assembly of this structure.
ASSEMBLY SAFETY and HELPFUL HINTS STOP!!! Check all parts and hardware before beginning. If any parts are missing or damaged please circle and call the phone number listed. DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET ! KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE AND MAINTENANCE REFERENCE. To aid in making your playset assembly easier, here is a listing of some helpful hints. Wear safety glasses during drilling, assembly of your playset.
SAFETY WARNINGS Please read carefully. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. This playset has been designed for use by a maximum of 10 occupants at one time having a combined weight of 1,050 pounds. (This weight does not include occupants in the sandbox area.) This playset is recommended for children (3) through (11) years of age. On-site adult supervision for children of all ages is recommended.
MAINTENANCE Periodic maintenance is required to ensure safe enjoyment of your playset and optional accessories. Observing the following procedures reduces the likelihood of serious or fatal injury. Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and tighten as required. T-nuts should be inspected for full and proper seating into the wood.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
PLAYSET ORIENTATION *Hint* Throughout this manual references made to the Left Side, the Right Side, the Front Side and the Back Side of the playset serve as a consistent reminder to help with assembly.
IMPORTANT! Use these Assembly Procedure Hints throughout the installation process. 1. All Lag Bolts must have pre-drilled holes. Use a 1/4” drill bit for all 3/8” Lag Bolts. Use a 3/16” drill bit for all 5/16” Lag Bolts. Pre-drilling pilot holes will help prevent Screws and Lag Bolts from breaking and wood from splitting during assembly. DO NOT OVER-TIGHTEN LAG BOLTS 2. In areas where drilling a larger 1/2” hole is neccessary, such as when installing T-Nuts, (Fig.
W O O D PA R T S L I S T 3/4 x 3-3/8 x 45-1/8" 2968-CC x1 1 x 3-3/8 x 45" 1 x 3-3/8 x 45-1/8" 1-3/8 x 3-3/8 x 18" 2899-CC x6 3/4 x 2-1/2 x 45-1/8" 1-3/8 x 3-3/8 x 51" 2970-CC x4 3/4 x 5-3/8 x 23-3/4" 2521-CC x1 1-3/8 x 3-3/8 x 51" 2971-CC x1 3/4 x 3-3/8 x 47-1/8" 2972-CC x2 3/4 x 5-1/2 x 44-7/8" 2691-CC x7 1-3/8 x 3-3/8 x 47-3/4" 2974-CC x1 3/4 x 5-3/8 x 23-3/4" 2960-CC x2 3 x 3 x 95" 2522-CC x1 2523-CC x16 1 x 5-1/2 x 45-1/8" 2966-CC x1 3 x 3 x 45-1/8" 3 x 3 x 95" 2525-CC x2 296
2485 Swing Beam 90o Plate Swing Beam Angled Plate Left Swing Beam Angled Plate Right x1 L-Bracket 2412 x2 Swing Hanger 2449 2448 x1 Swing Beam Flat Plate 2447 x1 2654 x1 x1 Stake Slide H A R D W A R E 90o Angle Bracket Plate 2631-B x6 x1 2411 WS 4521 x4 Trapeze Climbing Rocks O R I E S Swing WS 1501 x1 WS 4885 x2 Plaque Safety Handle S Rope WS 4545 x6 E S IN BAG x4 C SA 3097 x1 Telescope WS 4410 x3 Steering Wheel A C Plate SA 4220 x1 x4 SA 4294 x1 9
3/8" LOCK NUT 3/8" x19 3/8" x10 2-1/2" PAN HEAD SCREW 3/8" T - NUT x28 x20 3/8" FLAT WASHER 1/4" LOCK WASHER x48 1/4" x4 3/8" 5/16" T - NUT 3/16" x 1" FENDER WASHER S T E N E R S TRUSS HEAD SCREW 3/4" 3/8" LOCK WASHER x4 2-1/2" x4 Y L A x4 5/16" P 5/16" 1-3/4" PAN HEAD SCREW 1-3/4" x8 1/4" ROCK WALL HARDWARE Lock Washer x12 1-1/2" Hex Bolt 10 1" 5/16" FLAT WASHER 5/16" LOCK WASHER S E T F A x4 x10 Flat Washer T - Nut
3/8” HEX HEAD BOLTS x2 x4 x1 1-1/4" 1" 2" x8 3/8" 3-3/4" 3/8" LAG BOLT 3/8" 3/8" LAG BOLT L 5" P x4 3/8" A Y S T F 3" x2 E 3/8" x2 A 4" S T E 3/8" N WOOD SCREWS E x12 x195 2" 2-1/2" 3" 11 S x12 R x92 30 mm
x2 x6 x2 3-3/4" 3" x2 4-1/2" x2 6" x1 6-1/2" 8-1/2" 3/8" 3/8" HEAD BOLTS ” 3/8" 1-3/4” 2” 2-1/4” 3/8" 3/8” BUTTON HD. 3/8” SCREW 3/8" 3/8” BUTTON HD. SCREWHD.
PLAYSET SET-UP SAFETY AREA BACK SIDE 6' SAFETY AREA 30'- 2" 20'- 4" SWING 8'- 4" SLIDE HEIGHT 10'- 2" ROCK WALL 26'- 8" 13'- 4" 6' SAFETY AREA RIGHT SIDE 18'- 2" 6' SAFETY AREA LEFT SIDE 13'- 4" FRONT SIDE PLAYSET SET-UP WITH MONKEY BARS BACK SIDE SAFETY AREA 30'- 2" 6' SAFETY AREA 13'- 4" 6' SAFETY AREA LEFT SIDE 26'- 8" SWING SLIDE 14'- 2" HEIGHT 10'- 2" 13'- 4" MONKEY BARS 6' SAFETY AREA FRONT SIDE 13 29'- 0" RIGHT SIDE ROCK WALL 6' SAFETY AREA 18'- 2"
CORNER POSTS FORT 3" Lag Bolt Lock Washer Flat Washer 2954-CC Flush Note hole location. 3-3/4" Hex Bolt Lock Washer x2 Flat Washer Hole for Climbing Rope 2-1/2" Wood Screw x2 2968-CC x1 Flush 3/4 x 3-3/8 x 45-1/8" x2 47-1/4" 12-5/8" Flush 2899-CC x1 90° T-Nut x2 1 x 3-3/8 x 45-1/8" 3 x 3 x 95" 2954-CC x1 79-1/4" 2953-CC x1 3 x 3 x 95" Align braces with pre-drilled holes. Ensure all bracing is square before installing wood screws.
FORT FRAME BRACING 3/4 x 3-3/8 x 45-1/8" x2 2973-CC Note hole location. Ensure all bracing is square before installing wood screws. 1 x 3-3/8 x 45-1/8" x4 2899-CC 2-1/2" Wood Screw x10 3/4 x 5-3/8 x 45-1/8" Flush Flat Washer Lock Nut x2 Flat Washer x2 2969-CC x1 Flush 5" Hex Bolt x1 2969-CC Align braces with pre-drilled holes. BOTTOM 3/4 x 5-3/8 x 45-1/8" FORT FRAME BRACING 2-1/2" Wood Screw x2 3-3/4" Hex Bolt Lock Washer Flat Washer x4 Flush Note hole location.
FORT BOTTOM FRAME BRACE FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE. x6 2-1/2" Wood Screw 90° Flush 3/4 x 5-3/8 x 45-1/8" 2969-CC x1 Align brace with pre-drilled holes. Ensure all bracing is square before installing wood screws. Flush FORT Align braces with pre-drilled holes. CONNECT FRAME SECTIONS ENSURE THESE HOLES ARE ON THIS SIDE.
FORT DECK CLEAT 3/4 x 2-1/2 x 45" EQUA x1 2516-CC L EQUA L EQUA L EQUA L Flush 2-1/2" Wood Screws x4 Flush FORT SLIDE BLOCK Note this rope-hole location Center slide block (2490-CC) between 3x3 posts x2 2" Wood Screws 1-1/2 x 2-1/2 x 24" x1 2490-CC Flush L UA EQ L UA EQ Flush 17 2490-CC
FORT DECK PLANKS Flush with post.
FORT DECK SUPPORT x8 2" Wood Screws (2" screws into deck frame) 1-3/8 x 3-3/8 x 18" x4 2970-CC 2" Wood Screws from inside Flush to inside of 3x3 Flush 3" Wood Screws x8 (3" screws into 3x3 posts) 2" Wood Screws 3" Wood Screws Look for pre drills FORT DECK RAILS Note this rope-hole location 2973-CC 3/4 x 3-3/8 x 45-1/8" x2 2973-CC Bottom rests flush on lower brace Bottom rests flush on lower brace 2-1/2" Wood Screws x8 Flush at corners 19
FORT SWING BEAM SUPPORT Note this rope-hole location 6" Carriage Bolt x2 Torque Washer Small Holes UP 6" Carriage Bolt Flat Washer Lock Nut 2505-CC x1 SET ON RAIL 3 x 3 x 45-1/8" Flat Washer Torque Washer x2 Lock Nut FORT ROOF FRAME 2-1/2" Wood Screws x12 3/4 x 3-3/8 x 53-7/8" 2976-CC x2 4-3/8" 4-3/8" 20
STOP! IN THE NEXT STEP YOU WILL INSTALL THE RAFTER ASSEMBLY ACCORDING TO THE TYPE OF ROOF YOU HAVE (EITHER WOOD ROOF OR CANOPY). PLEASE REFER TO THE CORRECT ASSEMBLY.
ROOF FRAME FOR CANOPY Orient 2963-CC so that pre-drilled holes at the top are vertical. If the holes are not vertical, rotate the board. Secure 2964-CC and 2963-CC using 3" screws.
ASSEMBLE STEP LADDER 2-1/2" Wood Screws x16 1-3/8 x 3-3/8 x 51" 2522-CC x1 1-3/8 x 3-3/8 x 51" x1 2521-CC Flush to front face. Back side of ladder 2524-CC x4 1 x 3-1/2 x 15-3/8" ROCK WALL ASSEMBLE Rail (1826-CC) may have full or partiallly pre-drilled holes. Align screws with the pre-drilled holes in rails (1826-CC).
ROCK WALL ASSEMBLE Place planks onto rails (1826-CC and 2521-CC) as shown. If rails are fully pre-drilled, align all planks and screws with pre-drills. If rails are not pre-drilled, install planks flush to each other. Secure planks using 2-1/2" wood screws. 3/4 x 5-3/8 x 23-3/4" 2974-CC x1 HOLE 3/4 x 5-3/8 x 23-3/4" 2950-CC x5 2-1/2" Wood Screws x4 3/4 x 5-3/8 x 23-3/4" x1 2960-CC 2 23-3/4" Maintain Dimension ROCK WALL ASSEMBLE Install rocks at pre-drilled hole locations.
ROCK WALL ASSEMBLE x2 2 5/16" T-Nut 5/16 x 1-1/2" Button Head Screw 5/16" Lock Washer 2412 L-Bracket 5/16" Flat Washer x2 ROCK WALL INSTALL Flush Align ladder with inside of post and top of cross brace and mark holes.
ROCK WALL INSTALL FRONT SIDE Rock Wall SEE PAGE 7 Pre-drill two 1/4" pilot holes at marked locations. Re-drill holes from opposite side using 3/8" bit.
INSTALL ROCK WALL Flush with angle. 3/4 x 3-3/8 x 17" x1 2965-CC Flush with angle. 2-1/2" Wood screws x4 ROCK WALL INSTALL Secure middle brace with (2) 2-1/2" Wood Screws from behind.
INSTALL ANGLE BRACE 3/4 x 5-3/8 x 23-3/4" x1 2950-CC 2-1/2" Wood Screws x4 Lock Washer 2966-CC: Flush angle to inner corner of 3x3 post Flush Pre drill 3/16" pilot hole 2" deep for 4" lag bolt.
SWING BEAM SWING HANGERS Swing Hanger Bolt must protrude at least TWO Threads beyond Lock Nut. 3-3/8 x 5-3/ x 95" 2502-CC x1 IMPORTANT! 2 Threads MIN. Lock Nut Place Cap on threads after tightening Use a socket wrench to tighten Lock Nut securely against washer. 1-3/8" Washer Cap HOLD position of Swing Hanger while tightening Lock Nut. Lock Nut 1-3/8" Washer Swing Beam IMPORTANT! Final position of each Spring Clip is perpendicular to swing beam.
A - FRAME ASSEMBLE T-Nut x2 2525-CC x2 3 x 3 x 95" Rotate 2525-CC 180o after installing T-Nuts. A - FRAME ASSEMBLE 3-3/4" Hex Bolt x2 Lock Washer Flat Washer 2-1/2" Wood Screws x4 2978-CC x1 1 x 3-3/8 x 68-1/2" Pre-installed T-Nuts are underneath.
SWING BEAM FLAT PLATE 3" Carriage Bolt x2 x1 2411 x2 Flat Washer Lock Nut 90o PLATE A - FRAME 2499 x1 x2 3-3/4" Carriage Bolt Lock Nut Flat Washer 2525-CC 31
SWING BEAM ANGLED PLATES 3-3/8 x 5-3/8 x 95" 2502-CC x1 x2 DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME Flat Washer Lock Nut x1 2448 4-1/2" Carriage Bolt x2 x1 NOTE: You may need to tap bolts with hammer to get though holes. Clean all debris from bolt threads before installing lock nuts 2447 SWING BEAM ASSEMBLE Position swing beam assembly resting upon A-frame.
ASSEMBLE SWING BEAM Align holes and insert carriage bolt. Repeat where arrows are shown. NOTE: You may need to tap bolts with hammer to get though holes. Clean all debris from bolt threads before installing lock nuts x4 3-3/4" Carriage Bolt DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME Flat Washer Lock Nut SWING BEAM x4 ASSEMBLE 6-1/2" Carriage Bolt Torque Washer You may need to tap with hammer to get though holes.
INSTALL SWING BEAM Position swing beam assembly resting upon plate and align with holes. x1 8-1/2" Carriage Bolt x1 6-1/2" Carriage Bolt x1 Torque Washer 2485 Flat Washer x2 Lock Nut NOTE: You may need to tap bolts with hammer to get though holes. Clean all debris from bolt threads before installing lock nuts SWING BEAM 1. Pre-drill using 3/16" bit. x1 INSTALL SEE PAGE 7 2. Re-drill from opposite side using 7/16" bit.
INSTALL SWING BEAM x1 Flat Washer Lock Washer T-Nut x1 1" Hex Bolt SWING BEAM 2-1/2" Pan Head Screw ASSEMBLE x2 1/4" Lock Washer 35
BALUSTERS FORT 3/4" 3-1/4" 3/4" 3/4" Install end-balusters first, 3/4" from upright. 3-1/4" 3-1/4" 3-1/4" 3/4" 3/4" 30 mm Wood Screws SPACER SPACER 2977-CC SPACER SPACER x24 2523-CC x6 5/8 x 3-1/4 x 29-3/4" Flush BALUSTERS FORT Center first spacer and install balusters.
BALUSTER SUPPORTS FORT 3/4 x 3-3/8 x 12" 2975-CC x2 2-1/2" Wood Screw Flush at corner x4 2" Wood Screws into deck board ends x2 BALUSTERS FORT Install end-balusters first, flush with inside of posts.
ROOF NOTICE IF YOU HAVE THE WOOD ROOF OPTION REFER TO THE END OF THE MANUAL AT THIS TIME. IF YOU HAVE THE VINYL CANOPY ROOF CONTINUE AS FOLLOWS.
CANOPY INSTALL x1 2939 End Rail 3/4" Pan Head Screw (x10) 3/16" x 1" Fender Washer (x10) Install screws through hem for strength. x10 Fold tarp under canopy end rail.
INSTALL SWINGS Attach Playset Plaque using one 1" philips head screw (provided) at each corner of plaque. SA 4220 x1 WS 1501 TRAPEZE WS 4885 WS 4885 SWING SWING 8" 8" Minimum when occupied. Adjust chains at Top.
STEERING WHEEL INSTALL Install WS 4412 inside fort. Flat Washer 1-1/2" Lag Bolt DO NOT OVER-TIGHTEN LAG BOLTS. Steering Wheel Cap WS 4412 x1 TELESCOPE INSTALL Telescope and Bracket 1. Position Mounting Bracket in desired location (any Top Rail). WS 4610 x1 2. Attach Mounting Bracket to Top Rail using the Mounting Screw provided. 3. Insert the Telescope into the Mounting Bracket as shown.
INSTALL STAKES 1-1/2" Lag Bolts x2 Flat Washers x2 Metal Anchor Straps x2 Metal Anchor Straps x2 Flat Washers x2 SWING BEAM SIDE 1-1/2" Lag Bolts x2 WS 4521 x2 WS 4521 x2 Install stakes into 3 x 3" uprights. Locate stakes as shown. Make sure all base pieces and uprights are resting flat on the ground. It may be necessary to loosen the soil beneath Playset to make everything level. TOWER UPRIGHT A FRAME Instructions for anchoring your playset product to the ground. 1.
SLIDE INSTALL Locate Slide centered in the opening between Balusters on the FRONT SIDE of the Tower. 3/4" 1-3/4" Pan Head Wood Screw x3 2654 x1 CENTER CENTER FRONT SIDE Pre-drill 1/8" pilot holes through Slide at dimples, through deck planks, and into lower slide support. Ensure screws are installed through deck planks. Move slide slightly to avoid spaces between planks. SURFACING MATERIAL SLIDE (not included) Apply Surfacing Material at recommended depth, or deeper.
CLIMBING ROPE INSTALL OPTIONAL: Tie several single knots in locations to allow logical hand-grab points. Step 1 Feed top of Climbing Rope through front of Upper Rail (2968-CC) and tie a double knot on the back side (Fig. 1). Step 2 Feed lower end of Climbing Rope through hole in Rock Wall board (2974-CC) and tie a double knot on the back side (Fig. 1). For Safety, insure that the rope is tight enough so that it can not be looped back on itself.
SAFETY HANDLES INSTALL WS 4410 x3 1-1/2" Lag Bolt x6 Flat Washer DO NOT OVER-TIGHTEN LAG BOLTS. ACCESSORIES NOTICE IF YOU HAVE MONKEY BAR OR ACTIVITY TABLE REFER TO END OF THE MANUAL AT THIS TIME.
WARRANTY WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at:www.OnlineWarranty.net. Backyard Play Systems warrants the following: 1. All wood components have a Limited Five Year Warranty. 2. All non-wood components* have a three year Limited Warranty. *Ropes carry a one year Limited Warranty. 3. Installation labor has a three year Limited Warranty applicable on playsets installed by Backyard Play Systems.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
2694-RF - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information Call our toll-free number: 1-800-890-2211 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST or email: customerservice@backyardproductsllc.
(This page intentionally left blank.
2694-RF Backyard Play Systems Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 48162 Cedar Roof Accessory 01/29/2018 Model 4185, 4332, 4333, 4334, 4335, 6246, 6351, 6352, 6353, 6354, 6371 Recommended for Ages 3 to 11 Tools Required Phillips Bit Combo Drive Bit Cordless Drill w/Charger Drill Bits Tape Measure - BEFORE YOU BEGIN First... Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin.
W O O D PA R T S Roof Slat Top 5/8 x 5-1/8 x 51-1/8" 2987-CC x2 5/8 x 5-1/2 x 51-1/8" Roof Slat Mid 2989-CC x12 5/8 x 5-1/8 x 51-1/8" Roof Slat Bottom 2988-CC x2 5/8 x 1-1/2 x 20-3/8" 2991-CC x2 Sun Brace Center 5/8 x 5-1/2 x 13-3/16" 5/8 x 1-1/2 x 15-1/8" 2990-CC x12 Sun Brace Sun Decoration S U B - A S S E M B L E D D O R M E R PA R T S 3182-CC x1 Dormer Face H A R D WA R E 30 mm x36 3180-CC x1 Dormer Roof LEFT x74 3181-CC x1 Dormer Roof RIGHT 1-5/8" 2" x8 #8 Screw #8 Screw
ROOF FRAME INSTALL x12 1 x 3-3/8 x 47-1/8" 2-1/2" Wood Screws x1 2971-CC Flush 3/4" x2 2972-CC 3/4 x 3-3/8 x 47-1/8" Pre-drill 1/8" x 1" deep for screws to avoid splitting. SUN DECORATION INSTALL Pre-drill 1/8" pilot holes.
SUN DECORATION INSTALL Install 2991-CC centered and flush using two 30 mm screws as shown. Measure and mark rafter as shown. Install two 2990-CC's between marks using two 30 mm screws. 5/8 x 2 x 20-3/8" x1 2991-CC Flush at top. 5/8 x 2 x 15-1/8" Install 2931-CC First. 2990-CC x2 Flush at top. 2" 13 / -1 -1 / 2" 13 /2" 2-1 2-1 /2" CENTER 30 mm Wood Screws x6 SUN DECORATION INSTALL Center remaining 2990-CC's as shown. Install 2990-CC centered and flush using two 30 mm screws as shown.
ROOF PLANKS INSTALL Center 2987-CC roof boards on rafters. Ensure equal overhang on both sides; about 1". 1" Maintain 47-1/8" dimension between rafters. 1" 1-5/8" Wood Screws x8 5/8 x 5-1/8 x 51-1/8" 2987-CC x2 47-1/8" Flush at peak. ROOF PLANKS INSTALL BEGIN HERE Install all roof boards Flush. Insert panels fully seated.
ROOF PLANKS 1-5/8" Wood Screws INSTALL x32 5/8 x 5-1/2 x 51-1/8" 2989-CC x3 BEGIN HERE 5/8 x 5-1/2 x 51-1/8" x3 2989-CC x1 2988-CC 2988-CC x1 5/8 x 5-1/8 x 51-1/8" 5/8 x 5-1/8 x 51-1/8" DORMER ASSEMBLE Align brace of 3181-CC flush with right frame of 3182-CC. Ensure flush at peak, all along edge and at corner. Attach 3181-CC using #8 1-5/8" screws into middle of 3182-CC right frame. 1-5/8" Wood Screws x3 3181-CC x1 Flush along inner edge. 3182-CC x1 Pre-drill 1/8" holes through 3182-CC.
DORMER ASSEMBLE Align brace of 3180-CC flush with left frame of 3182-CC. Ensure flush at peak, all along edge and at corner. Attach 3180-CC using #8 1-5/8" screws into middle of 3182-CC left frame. Flush Flush 3182-CC x1 1-5/8" Wood Screws x3 Pre-drill 1/8" holes through 3180-CC. Flush along inner edge. 3180-CC x1 Flush DORMER INSTALL Attach assembled dormer using #8 2" screws into roof planks as shown. Install screws through dormer roof frame (Fig. 1). Pre-drill 1/8" holes.
8
WARRANTY Backyard Play Systems warrants the following: 1. All wood components have a Limited Five Year Warranty. • Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unfit due solely to damage caused by fungal decay or termites. 2. All non-wood components* have a three year Limited Warranty. *Ropes carry a one year Limited Warranty. 3. Installation labor has a one year Limited Warranty applicable on playsets installed by Backyard Play Systems.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
2695-RF - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! IMPORTANT: THIS MANUAL SUPERSEDES THE MANUAL PACKED IN YOUR KIT. USE IT TO ASSEMBLE YOUR MONKEY BARS! NOTE: YOU MAY HAVE EXTRA FASTENERS AFTER FINISHING ASSEMBLY. Call Us First! DO NOT RETURN TO STORE.
(This page intentionally left blank.
2695-RF Backyard Play Systems Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 48162 10/24/2017 Model 34037 Monkey Bar Accessory Recommended for Ages 3 to 11 Tools Required Socket Set Ratchet Socket Extension Hammer Phillips Bit - BEFORE YOU BEGIN First... Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin.
M O N K E Y B A R PA R T S L I S T End Ladder Angle Brace Anchor 1-3/8 x 3-3/8 x 57" 2983-CC x2 WS 4522 x2 End Ladder Bottom Support 1-3/8 x 3-3/8 x 80-1/2" 2985-CC x1 Top Ladder Rail Support 1-3/8 x 3-3/8 x 78" 2984-CC x2 End Ladder Rail Support 1-3/8 x 3-3/8 x 81-1/16" 2 2986-CC x2
M O N K E Y B A R H A R D WA R E - NOTICE - Depending on your playset model, you will have extra hardware left over. 3/8" x 1-1/2" BUTTON HD.
MONKEY BAR METAL PARTS 18-1/2" Flat Metal Bracket L-Bracket 2023 x2 Top Rung 2084 x2 PF 4972 x5 21-1/2" End Rung PF 3297 x3 FASTENERS FOR METAL RUNGS 2-1/2" Lock Washer x16 x16 Flat Washer 1/4" Pan Head Screw Space intentionally left blank.
PLAYSET ORIENTATION BACK SIDE 6' SAFETY AREA LEFT SIDE REFER TO PLAYSET INSTRUCTION MANUAL FOR SAFETY AREA RIGHT SIDE 6' SAFETY AREA FRONT SIDE TOP RAIL MONKEY BARS 1-3/8 x 3-3/8 x 78" 2984-CC x2 1" x 18-1/2" PF 4972 x5 2-1/2" Pan Head Screw 1/4" Lock Washer Align with pre-drilled holes Flat side against wood.
END RAIL ASSEMBLY 1-3/8 x 3-3/8 x 81-1/16" 2986-CC x2 1 x 21-1/2" PF 3297 2-1/2" Pan Head Screw x6 x3 1/4" Lock Washer Flat side against wood.
END LADDER / TOP LADDER ASSEMBLY END RAIL Flat Washer Lock Washer 1-1/2" Button Head Screw T-Nut 3-1/4" Hex Bolt TOP RAIL Lock Washer Flat Washer T-Nut 1-1/2" Button Head Screw Flat Washer Lock Washer 3-1/4" Hex Bolt 7 Lock Washer Flat Washer
INSTALL ANGLE BRACES / BOTTOM SUPPORT Flat Washer (x2) Lock Washer 3-3/4" Hex Head Bolt (x2) T-Nut 1-3/8 x 3-3/8 x 57" 2983-CC x2 2-1/2" Hex Head Bolt (x2) Lock Washer Flat Washer 4-3/4" Hex Head Bolt (x2) T-Nut 2985-CC x1 1-3/8 x 3-3/8 x 80-1/2" 2-1/2" Hex Head Bolt T-Nut (x2) Lock Washer Flat Washer (x2) T-Nut NOTE: Counter-bore of 2985-CC toward rear side of ladder.
MONKEY BAR INSTALL POSITION * USE CARE WHEN INSTALLING MONKEY BAR ASSEMBLY SLIDE SIDE SWING BEAM SIDE * TWO PEOPLE AND A STEP LADDER ARE RECOMMENDED FOR THIS STEP MONKEY BAR INSTALL - STEP 1 10" FROM INSIDE OF 3x3 CORNER POST. Flush at TOP. 10" Mark two drill-holes. 9 *Hint – Clamp Monkey Bar Assembly in place while marking holes.
MONKEY BAR INSTALL - STEP 2 Drill-Through 3/16" marked locations. Re-Drill through using 7/16" bit from inside fort.
INSTALL ANCHOR STAKES Metal Straps 1/4 x 1-1/2" Lag Bolts x2 WS 4522 x2 Flat Washers Install on Bottom Rail. x2 x2 Instructions for anchoring your playset product to the ground. 1. Determine the final location of your playset product. 2. Place the Anchor Stakes adjacent to the base and near the corners of your playset product (at the bottom of the legs on swing sets) and twist the auger-style Anchor Stakes into the ground until only the loop is exposed. 3.
WARRANTY Backyard Play Systems warrants the following: 1. All wood components have a Limited Five Year Warranty. • Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unfit due solely to damage caused by fungal decay or termites. 2. All non-wood components* have a three year Limited Warranty. *Ropes carry a one year Limited Warranty. 3. Installation labor has a one year Limited Warranty applicable on playsets installed by Backyard Play Systems.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
2696-RF - NOTICE This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information Call our toll-free number: 1-866-890-2211 April through October M - F 8:00 AM to 6:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST or email: customerservice@backyardproductsllc.
(This page intentionally left blank.
2696-RF Backyard Play Systems Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 48162 10/24/2017 Model 34033 Activity Table Accessory Recommended for Ages 3 to 11 Tools Required Phillips Bit Combo Drive Bit Cordless Drill w/Charger Drill Bits Tape Measure - BEFORE YOU BEGIN First... Check with your homeowner’s association before assembling. Read instructions thoroughly before you begin.
A C T I V I T Y TA B L E PA R T S L I S T 3/4 x 3-3/8 x 20-1/2" Seat Board 3/4 x 3-3/8 x 14" 2980-CC x2 Table Board 2979-CC x2 3/4 x 3-3/8 x 27-1/4" Upright Brace 2981-CC x2 3/4 x 5-3/8 x 44-7/8" Table Board 2898-CC x2 1 x 5-3/8 x 44-7/8" Seat Board 2982-CC x1 H A R D WA R E 1-1/4" 2" x22 x22 #8 Screw #8 Screw 2
SEAT SUPPORT INSTALL 2" Screws x4 EL 3/4 x 3-3/8 x 20-1/2" V LE x2 2980-CC NOTE: THIS SIDE TO SWING BEAM SIDE 13-3/8" LEVEL EL V LE 13-3/8" Flush TABLE SUPPORT INSTALL 2" Screws x4 3/4 x 3-3/8 x 14" x2 2979-CC EL V LE Flush LEVEL 24-3/8" 24-3/8" 3 EL V LE
UPRIGHT BRACE INSTALL Install (2) 1-1/4" screws into each side. Make sure seat and table supports are level before securing with 1-1/4" screws.
WARRANTY Backyard Play Systems warrants the following: 1. All wood components have a Limited Five Year Warranty. • Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unfit due solely to damage caused by fungal decay or termites. 2. All non-wood components* have a three year Limited Warranty. *Ropes carry a one year Limited Warranty. 3. Installation labor has a one year Limited Warranty applicable on playsets installed by Backyard Play Systems.
WARRANTY Please feel free to call our Consumer Help Line Toll Free 1-866-890-2211 April through October M - F 8:00 AM to 7:00 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST No warranty is offered on the following: (1) equipment subject to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own: or (2) equipment subjected to improper use, service or repair by customer or any third par
