Owner manual

ManualsBrandsSwiftech ManualsComputer AccessoriesMCW6500 T 775

This product is intended for expert users only. Please consult with a qualified technician for installation. Improper installation may result in damage to

your components.

Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their

installation.

The following instructions are subject to change without notice. Please visit our web site at www.swiftech.com for updates.

MCW6500-T 775 Bill of Materials Table

ITEM NO. PART NUMBER DESCRIPTION QTY

1 MCW6500-T 775

Thermoelectric water-block assembly

2 MCW6500-MBGSKT

soft neo sponge 1/4" thick - peel-off

3 Motherboard Socket 775 1

4 MCW6500-775-HARDWARE

Assembly composed of parts below

6-32-Acorn-nut 6-32 Acorn nut 1

4.2 SPRING6

Spring

4.3 6-32-nut 6-32 nut 1

4.4 LOCK-WASHER#6 Lock washer 1

4.5 FW140X250X0215FB BLK black fiber washer 2

4.6

6-32x2.0-philips 2" Philips screw

4.7 12SWS0444 Nylon shoulder washer 1

Foam insert from one of the motherboard gaskets

4.1

4.7

4.2

4.3 4.4 4.5

4.5

4.6

MCW6500-MBGSKT

Figure 1

Rouchon Industries, Inc., dbA Swiftech™ – 3700 Industry Ave., suite 104, Lakewood CA 90712 USA – T (562) 595-8009 – F (562) 595-8769 – All

content Copyright Swiftech 2007 – Last edited 2-15-07 – Subject to revision without notice - 1 of 4 -

Summary of content (4 pages)

PAGE 1
This product is intended for expert users only. Please consult with a qualified technician for installation. Improper installation may result in damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.swiftech.com for updates. MCW6500-T 775 Bill of Materials Table ITEM NO.
PAGE 2
1. Condensation control measures The following instructions are crucial to long lasting & reliable operations. Do not skip these steps, and do not take shortcuts. Permanent damage to your components is likely to occur otherwise. a. Motherboard preparation i. Conformal coating application: This step will positively ensure that any micro condensation occurring on small surface mount components will not corrode or short-circuit the motherboard. Procure a spray can of silicone conformal coating. We use M.G.
PAGE 3
Step 4 - Wipe off the back of the motherboard clean, and stick the neoprene gasket directly behind the CPU (use the center section of a motherboard gasket). 2. Step 5 Step 6 - Install the 4 posts (item 4 figure 1) into the motherboard mounting holes: 6-32 screw, black fiber washer, screw thru motherboard, then black fiber washer, lock washer, and 6-32 nut. - Make sure to fasten the 6-32 nut firmly, preferably using a 5/16 socket.
PAGE 4
For your convenience, the MCW6500-T 775 is shipped with pre-installed ½” barb (1/4” BSPP thread) Type of Coolant: For best performance, use 95% distilled water, and 5% Swiftech brand “HydrX” corrosion inhibitor (available here: http://www.swiftnets.com/store/category.asp?CatID=2, under the “accessories” section). You should preferably use distilled water together with a corrosion and algae inhibitor with your water-block. Regular automotive anti-freeze is acceptable.