User guide

Parts list

Parts QTY PARTS QTY

MCW6000 or 6002-PX™ water-block 1 6-32 x 1 ¼” Philips screws 4

Worm drive clamps 2 Springs 4

SP4 hold-down plate 1 Standoffs 4

4-40 Nylon retaining washers 4 Black fiber washers 8

Locknuts 4 Céramique thermal compound 1

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation

may result in damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of

these products, nor their installation. The following instructions are subject to change without notice. Please visit our web

site at www.swiftnets.com

for updates.

The MCW6000 or 6002-PX water-blocks can be installed using two different

methods:

 Using the spring-loaded screws and standoffs included with the water-block (fig. 1 below)

 Using the plastic retention frames and spring clips included with most motherboards (fig. 2 page 2)

ssembly using our

spring-loaded screws

and standoffs

ITEM NO. PART NO. DESCRIPTION

1DUAL-XEON-BOARD Motherboard

2 STANDOFF swtainless steel hexagonal 1/4" standoff

3 6-32-LOCKNUT 6-32 LOCKNUT

4 FW140X250X0215FB BLK black fiber washer

5 MCW6000-P-with-bracket MCW6000-P water-block assembly

a MCW6000-FLAT MCW6000 waterblock flat base

b SP4-Bckt SP4 Holding plate for Intel Pentium 4 and Xeon

6 91772A154-phil6x32x1.125 6-32 x 1 1/4" philips scfrew

7 70750 0.042 diam Heavy Duty spring

8 4-40 nylon retaining washer 4-40 nylon retaining washer

FLUID INLET

FLUID DISCHARGE

Figure 1

Rouchon Industries, Inc., dba Swiftech – 1703 E. 28

Street, Signal Hill, CA 90755 – Tel. 562-595-8009 – Fax 562-595-

8769 - E Mail: Swiftech@swiftnets.com – URL: http://www.swiftnets.com

- Information subject to change without notice

Page 1 of 3

PAGE 1
Parts list Parts MCW6000 or 6002-PX™ water-block Worm drive clamps SP4 hold-down plate 4-40 Nylon retaining washers Locknuts QTY 1 2 1 4 4 PARTS 6-32 x 1 ¼” Philips screws Springs Standoffs Black fiber washers Céramique thermal compound QTY 4 4 4 8 1 This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your components.
PAGE 2
16 1 2 3 4 PART NO. DUAL-XEON-BOARD RETENTION XEON-CLIP MCW6000-P-with-bracket a MCW6000-FLAT b SP4-Bckt DESCRIPTION Motherboard Plastic retention frame, included with motherboard Xeon clip included with motherboard MCW6000-P water-block assembly MCW6000 waterblock flat base Hold-down plate for Intel Pentium 4 and Xeon A SSEMBLY USING PLA STIC FRAME AND SPRING C LIPS INCLUDED W ITH MOTHERBOARD 3 FLUID INLET FLUID DISCHARGE 4b 1 4a 2 Figure 2 1.
PAGE 3
. Water-block installation The MCW6000 series can be installed using two different methods (also see figure 1 and 2): Using the spring-loaded screws and standoffs included with the water-block (fig. 1), or Using the plastic retention frames and spring slips included with most motherboards (fig. 2) You may use either method at your convenience. For installation with our own spring loaded screws, follow the instructions below.