Instruction Manual

Intr
oduction
Congr
atulations on the purchase of your Swann Wi-Fi
NVR Security Camera.
• 4K Ultr
a HD video with sensor spotlight, siren
plus red & blue flashing lights
• T
rue Detect™ Heat & Motion sensing for reli-
able alerts
• P
owerful Night2Day™ color night vision
• W
orks in rain & snow all year round
Important instructions
1. Make sure the camera is fixed correctly and stable
if fastened in place.
2. Never place strain of any kind on the power con-
nection and/or power adapter.
3. Do not operate if wires and terminals are exposed.
Important Note: All jurisdictions have specific laws
and regulations relating to the use of cameras. Be-
fore using any camera for any purpose, it is the buy-
er’s responsibility to be aware of all applicable laws
and regulations that limit the use of cameras.
About this Manual: The content in this manual is for
information purposes only and is subject to change
without notice. While every effort is made to ensure
that this manual is accurate at the time of printing,
no liability is assumed for any errors that occurred.
The c
amera can be mounted onto a flat surface using the screws and wall plugs provided. The surface must
have sufficient strength to hold the camera (the camera illustrated is for instructional purposes only).
→ P
osition the camera in the location you want to mount it, and mark the screw holes on the surface to
position the screws (a mounting template has been included). Then, using the appropriate screws for the
surface you’re fixing the camera to, secure the camera in place.
→ If y
ou’re mounting to a wooden surface, then screw the camera directly to the surface.
→ If y
ou’re mounting to a masonry surface (bricks, concrete or similar), then you’ll need to use wall plugs.
1 Mounting the Camer
a
4
Aiming the c
amera
1. Loosen both screws (use a Phillips head screwdriver) to ad-
just the camera’s orientation. This enables you to rotate the
camera so no matter what direction it is facing, your images
will be the right way up. Tighten each screw to secure in place.
2. Loosen the screw to tilt the camera up or down. Tighten the
screw to secure in place.
3. To pan the camera left or right, loosen the screw and position
accordingly. Tighten the screw to secure in place.
Connect the output
on the power cable to the power input on the camera then connect the input on the power
cable to the power adapter. The pair/reset button is used to restore factory default settings and to pair the
camera to your NVR (if network settings are changed or when adding a new camera).
Connecting the Camer
a
2
2
Powe
r
Output
Power
Input
P
ower Cable
Power Adapter
3
1
Powe
r
Input
P
air/Reset
Leav
e the antenna in a vertical
position for best reception.
Connect the power adapter to
a power outlet then press the
outlet’s switch to the ON posi-
tion to supply power.
P
airing the Camera
3
F
or instructions on how to configure your camera
for motion detection, changing image settings,
and other functions available, please consult the
manual for your NVR. Go to support.swann.com,
search for your model, then download.
1. In Live View mode, click a channel that you want to pair the camera to.
2. A Pair button appears. Press this button to commence pairing. A message will appear stating that you need
to press the pair button on the camera.
3. Remove the cap covering the pair button. Press and hold the pair button for 3 seconds then release. The
camera will commence pairing and the camera’s IR LEDs will start flashing.
4. After a short moment the camera will be paired and you will see the camera’s image on-screen. If the camera
fails to pair, repeat the above instructions and try again.
Channel 2
28/04/2021 01:14:41 P
M
Channel 3
28/04/2021 01:14:41 P
M
Channel 4
28/04/2021 01:14:41 P
M
Off-line
Pr
ess the Pair button to
commence pairing.
2
1
3