2400W steam generator with one touch temperature control CERAMIC SERIES Instruction Manual MODEL: SI9032N
WWW.SWAN-BRAND.CO.
Important Safeguards 1. Make sure to read all the safety precautions below and look at the illustrations before you start using the appliance. 2. Use the appliance for its intended use only. 3. The appliance is intended for household use only. 4. In order to protect against the risk of electric shock, do not immerse iron power base into water or any other liquids 5. Connect the appliance only to an alternating current of the voltage specified on the rating plate and only to an earthed socket.
WWW.SWAN-BRAND.CO.UK 16. The iron must not left unattended while it is connected to the supply mains. 17. The appliance must be used or stored in a level and horizontal surface. 18. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable. 19. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. 20.
Parts and Features 1. Water tank 2. Handle 3. Soleplate 4. Temperature selection button 5. Steam button 6. Steam button lock 7. Steam release button 8. Ready indicator light 9.
WWW.SWAN-BRAND.CO.
Fabric Setting Chart Temperature Setting Synthetics low setting Wool Cottton medium setting high setting Fabric Synthetics Silk Nylon Acrylic Acetate Wool Polyester Rayon Cotton Linen Rayon Cotton Linen Ironing Instruction Dry iron on the opposite side of the fabric Use a press cloth and steam iron on the opposite side of the fabric Iron while fabric is still damp Steam iron Steam Selection Linen max setting
WWW.SWAN-BRAND.CO.UK Ironing Temperature Setting Guide 1. Follow the ironing instructions on the garment label. If there is no instruction label, but you know what kind of fabric it is, please refer to the fabric setting chart described opposite. 2. The fabric setting chart is only valid for plain fabrics and not for materials to which finishes, glosses etc, have been applied. Textiles to which some kind of finish has been applied (gloss, crinkle, relief etc.) is best ironed at a lower temperature. 3.
How to use your Steam Station Prepare the Appliance for use 1. Check if the rating indicated in the rating plate corresponds to the main voltage in your home. 2. Press handle button to lay handle down. (When handle is lifted up, the unit is shut off. It will be ON when handle is laid down). 3. Remove the protective foil or sticker or card from the sole-plate. 4. Fully unwind and straighten the power cord and the supply hose. 5.
WWW.SWAN-BRAND.CO.UK Fill Water Tank If there is no water or not enough water in the tank, the filling indicator light on control panel will start blinking. An alarm will sound 5 BEEPs to indicate filling is needed. 1. Press the water tank lock upwards and slide the detachable water tank outwards from the base. 2. Take the filter upwards out from the water fill hole.
Steam Ironing 1. Fill water tank with clean tap water refering to the filling instructions. For better performance, please immerse filter in water for several minutes before installing it into the water tank. 2. Connect the appliance to a suitable socket outlet. The power indicator light (red) “ ” will light up on the iron unit showing that the unit has been connected to the power supply. 3. Set selection button to desired position according to fabric setting chart on page 08.
WWW.SWAN-BRAND.CO.UK Note: a. For first use, it is normal that a slight vibrating sound may occur from the electrical pump inside the base unit for a few seconds when steam ironing is started. It is because there is air inside the filter. It will stop when the air inside the filter has been pumped out. If this abnomal condition continues to happen for more than 60 seconds, please check whether water tank and filter is assembled correctly. b.
Vertical Steam Ironing • Follow the steam ironing process, and then hold the iron in a vertical position between 5cm and 15cm away from the hanged fabrics. • Press down steam switch, this will create vertical steam. • This feature is especially used for removing creases from hanging clothes and curtains. • Never directly perform steam ironing on people. vertical Auto Shut Off Function The appliance will come into auto shut off mode along with audible “Bi...
WWW.SWAN-BRAND.CO.UK Handle A handle is attached to the base unit for carrying the appliance. It also serves as a power on/off switch: Lifting the handle up turns power OFF and putting the handle down turns power ON. Before use, please put the handle in the down position as follows: • Press down the two handle buttons at the same time, and then lay the handle down.
Replacement of Filter Method: 1. The filter replacemnent indicator light will blink continuosly when the filter needs to be replaced. 2. To replace; slide water tank out from base unit, take the filter out from the water tank, and then replace with a new one. 3. After new filter has been installed into water tank, fill water into water tank to MAX fill level, and then slide water tank back into base unit. (Immerse filter in water for several minutes in order to gain better performance in future use). 4.
WWW.SWAN-BRAND.CO.UK Anti-Calc System anti-calc 1. The filter is designed to reduce the build-up of limescale which occurs during steam ironing to prolong the working life of your iron. However, please note that the filter will not completely stop the natural process of limescale build-up. 2. The filter should be replaced with a new one after 2-3 months. The iron can still be used with a clogged filter. However, limescale will most probably be built up in the steam chamber.
Troubleshooting Problems Possible Causes Solution Iron won't heat. Incorrect connection to the mains socket. Re-plug the unit to mains socket. Handle has not been laid down. Lay down handle. Temp setting is at " position. " Select the required ironing temperature according to Fabric Setting Chart. Unknown malfunctions. Take to a qualified serviceman or manufacturer or its service agent for examination and repair. Temperature setting is at NYLON position.
WWW.SWAN-BRAND.CO.UK 2 Year Guarantee This product is guaranteed for two years from the date of original purchase. If any defect arises due to faulty materials or workmanship faulty products must be returned to place of purchase. Refunds or replacement is at the discretion of the store. The following conditions apply: • The product must be returned to the retailer with original proof of purchases.
WWW.SWAN-BRAND.CO.UK Distributed by Swan Products Ltd PO Box 3117 Stoke-on-Trent ST4 9GD Made in China Please note the photographs and illustrations within this manual are for illustration purposes only.
