Installation Guide

SW-07038AD Shower Wall Kit
One back panel
One left corner panel
One right corner panel
One left side panel
One right side panel
One tube of color match silicone sealant
Designed for shower enclosures 38 inches wide and 36 inches
deep. Wall panels are 70 inches high.
For best results, use 100% clear silicone sealant for bonding
this product to a properly constructed and prepared sub wall.
You will need one tube of 100% clear silicone sealant (tube
sized to fit a standard caulking gun) for every 1440 square
inches, or 10 square feet, or, 4 to 10 tubes for an average
shower. Follow the application recommendation located in the
Panel Installation section of this manual.
Unpack Carton
m Use care when opening the box so that you do not damage
the panels.
m This product is shipped to you or your retail center after
careful inspection. After purchasing the kit, carefully unpack
and inspect the product for any shipping damage that may
have occurred. If damage is found, report it immediately
to the store of purchase. After inspection and during
installation, protect the products from construction damage
by moving them to another room or area until ready to
install.
m Store panels in a flat area to avoid warpage until the time of
installation. Do not store the panels outside of the original
packaging in a vertical position.
m Please use the model number located on the side of the
box, or the front of this manual, when contacting us with
questions concerning the installation of this unit.
m Make sure the walls are the correct size and are in good
condition. Installation of damaged product will void the
warranty.
Helpful Hints
m Read these instructions carefully and familiarize yourself
with the various parts of the kit.
m The variety of installations possible for this kit may require
procedures other than those shown. Ensure construction is
correctly sized, plumb, and square.
m Save the large cardboard box for protection of the shower
floor or bathtub during the installation process and to use as
a template for cutting the wall panels.
m Allow sufficient time for the parts in this kit to adjust to room
temperature. We do not recommend installation of this
product at temperatures below 65 degrees.
m Sawhorses with 2 x 4 cross-members or a worktable are
helpful during the installation process.
m Always transport the panels vertically. Use care when
laying the panels flat to prevent flexing, especially when
panels have a cutout in them.
m Store unused materials away from the work area to prevent
accidental damage.
m If the shower or bathtub is placed over a garage or on an
outside wall, care must be taken to ensure that the shower
or bathtub is properly insulated from cold temperatures.
Preparation Tips
m Measure the width of the back wall (with green board)
installed. This measurement cannot exceed the width of
the Swan Corporation back panel(s). If the wall opening
is too small or too large, other methods will be required to
cover the wall.
m Measure the height above the bathtub or shower base.
If this measurement is less than the height of the Swan
Corporation back and side panels, then the panels must be
cut to fit.
m Turn off the hot and cold water supply.
m Remove faucet handles, escutcheons, filler spouts, and/or
anything mounted to the wall (i.e. towel bars, soap dishes,
etc.).
m Always measure the location of the plumbing cutouts, as
stated in the instructions for each specific Swan Corporation
tub wall kit. Make a cardboard template to trial fit all
plumbing cutouts before cutting panels.
m Ensure all plumbing or electrical work inside the walls is
finished prior to installation of the wall panels.
m Prepare the area with 1/2 inch (13 mm) moisture-resistant
drywall, marine grade plywood, or concrete board. Never
install our products directly on any structure that is, or may
become, wet or damp.
m Trial fit the side panels before you begin. Swan Corporation
panels have a finished side and a unfinished backer side.
The unfinished backer side should be placed against the
sub-wall.
m Walls must be solid, plumb, and square within 1/8 inch of
true. Shim or trim the opening, as required. This kit has
been designed with some adjustability for minor alignment
problems.
m The mounting surface must be free of dirt, film, waxes, or
any other residues.
m If you are installing a recessed accessory, cut the hole
after the panel is installed and fully supported by the wall.
Remember to position the accessory between the wall
studs.
Caulking Tips
m Follow the instructions on the color match silicone sealant
tube.
m When job is complete, inspect all caulked areas for gaps
and fill as needed.
m Clean up any excess silicone using denatured alcohol and a
clean cloth.
m Be very careful not to disturb caulk joints.
800-325-7008 5 Swan
General Information