User's Manual Model No. CVQ1000 WIRED COLOR CAMERA WITH QUAD PROCESSOR & REMOTE CONTROL PLEASE READ CAREFULLY AND SAVE This manual contains important information about this product's operation. If you are installing this product for use by others you must leave this manual -or a copy-with the end user.
Important! Please read this booklet carefully before installing or using these units. WARNING-These units should ONLY be opened by an authorized technician if service is required. Safety Precautions For correct and safe operation of this system, it is essential that installers, end-users and service technicians should follow all safety procedures outlined in this manual. Specific Warning and Caution statements (and/or symbols) are marked on the units where needed.
Parts Included with This System 1. 4 Channel Switcher Box 2. Remote Control 3. Color Camera With Mounting bracket 4. 60ft Cable 5. Video Cable 6. 12V DC Adaptor for the Switcher x 1 set x 1 pc x 4 pcs x 4 pcs x 1 pc x 1 pc Parts of the System Parts of the Camera A. B. C. D. Mounting bracket IR LED Camera Din Connector Camera Lens Installation and Adjustment A. Camera Installation 1. Install or mount the camera at the desired location.
B. SWITCHER Installation 1. Connect the adaptor to the adaptor jack [DC IN] and plug it to a wall outlet. 2. Connect the DIN plug to the output jack, connect the other end to your TV or monitor. 3. Connect the DIN jack to the camera DIN plug. 4. After connecting all the cameras; apply DC12V power supply to system, the power indication LED will light up and indicate camera number on channel display LED. System Features A.
1 PIP Screen Mode 2 PIP Screen Mode Auto Sequence Mode D. High Performance Freeze Function Flicker Free Image Captured E. High Performance Zoom Function Selectable Zoom Area F. Various Overlay Information Camera Title Real Time and Date Alarm/Loss/Motion Message G. Provide Various Event Input Video Loss Detection Motion Detection 60 Event Report Built-in Buzzer H. Power Jack Connection DC 12V/1A, 2.1mm Jack, Center is positive. Description Of Control Front panel. 1. Power Led. 2. Zoom Led. 3.
Functions of Control Buttons When each button is pressed, the corresponding LED above the button will be ON. 1. Press button FREEZE / AUTO for 3 second to get the sequential displays of channel 1, channel 2, channel 3, channel 4, and Quad respectively and proceed in cycle. Or press the button less than 1 second to freeze the picture on the display, press again to unfreeze. 2. Press MENU button for 3 second to enter SETUP MENU. This button can also be used as EXIT. 3.
Remote Control Functions: 1. MENU button: Please see menu setup section. 2. FREEZE button: Press any channel to get full screen display, and then press FREEZE to freeze the picture. Press FREEZE again to unfreeze. 3. ZOOM button: Press ZOOM button to achieve zoom in display. Press buttons to choose zoom area. Press Zoom button again to achieve zoom in display. Press buttons to get full area display or press ZOOM to re-choose zoom area 4.
A. System setup: y Date / Time: Press to move the cursor to the desired section wish to adjust. Press to adjust the section. y System Format: Choose PAL / NTSC y Key lock: To enable / disable button on the system box. y Factory reset: To reset to factory default setting. y To exit, press MENU button again. B. Display setup: y Display on screen: To display title / date / time on the screen by check the box beside. To disable by un-checking the box.
E. Motion setup: y Camera 1: Choose desired camera. y Detection Time: To enable / disable detection of the cameras. y Masking area: To disable some area you wish not to detect. y To exit, press MENU button again. F. Event setup & Event report: y Loss: If any camera loss its signal, the report will go to Event report. y Motion: Any motion detected in front of camera, the report will go to Event report. y Buzzer hold time: To enable or disable buzzer function and can be set from OFF to 99 sec..
Product Specification Camera Remote Control/Switcher Frequency N/A 310/434 MHz (switcher) Channel Scan Period IR LED Video Format H Resolution Operation Temp Power Consumption Power Supply Video Input Video Output Size (mm) Accessories N/A 11 NTSC/PAL 330 TV Lines -10~50oC 0.22W From Switcher N/A 1 Vp-p/75 ohm 105x55x86 mm 60ft Cable for camera 1-99sec (adjustable) N/A NTSC/PAL N/A N/A 100mA DC 12V /1A Adapter DIN x 4 DIN x 1 218x202x44 mm DC 12V DC/1A Adapter Camera Module Lens 6.0mm/ F2.
