User's Manual

ManualsBrandsSuzhou Switek Electronics & Technology ManualsElectronicsCAT5 LCD CONTROL PLATFORM

CAT5 LCD CONTROL PLATFORM User

Manual

KVM SWITCHES PACKING LIST

Type Name Num/Unit Note

AS-31TLG

Series Products

CAT5 LCD CONTROL

PLATFORM

15 inches LCD screen, keyboard and

mouse control platform integrated

CAT5 LCD CONTROL PLATFORM

with multiple ports (4/8/16ports RJ45

port).

AS-71TLG

Series Products

CAT5 LCD CONTROL

PLATFORM

17 inches LCD screen, keyboard and

mouse control platform integrated

CAT5 LCD CONTROL PLATFORM

with multiple ports (4/8/16ports RJ45

port).

AS-91TLG

Series Products

CAT5 LCD CONTROL

PLATFORM

19 inches LCD screen, keyboard and

mouse control platform integrated

CAT5 LCD CONTROL PLATFORM

with multiple ports (4/8/16ports RJ45

port).

AC Power Power Cable 1 AC power connecting cable

KVM Control User

Manual

User Manual 1/2 LCD Manual and KVM Manual

KT-150(USB)

KT-250(PS/2)

Dongle Optional Connection encoder

Please check the lists carefully and contact with your dealer if you have some problems.

Please read the manual carefully before installation.

Summary of content (15 pages)

PAGE 1
CAT5 LCD CONTROL PLATFORM User Manual KVM SWITCHES PACKING LIST Type Name Num/Unit 1 15 inches LCD screen, keyboard and mouse control platform integrated CAT5 LCD CONTROL PLATFORM with multiple ports (4/8/16ports RJ45 port). 17 inches LCD screen, keyboard and mouse control platform integrated CAT5 LCD CONTROL PLATFORM with multiple ports (4/8/16ports RJ45 port). 19 inches LCD screen, keyboard and mouse control platform integrated CAT5 LCD CONTROL PLATFORM with multiple ports (4/8/16ports RJ45 port).
PAGE 2
Content OVERVIEW .............................................................................................................................................................. 3 PRODUCT TYPE...................................................................................................................................................... 3 FEATURES ...............................................................................................................................................................
PAGE 3
OVERVIEW CAT5 LCD CONTROL PLATFORM is one witch integrate a multiple ports KVM switch into 1U height. It controls multiple computers with one platform (keyboard, mouse and monitor). It is easy and quick to install. Just connect the wire to the correct port without software configuration. So there is no difficulty in installation and incompatibility. KVM switch provides two methods to control the computers connected to it: 1. By buttons on the platform. 2. By OSD operation.
PAGE 4
FEATURES Control Platform Control platform with LCD, keyboard, mouse and multiple ports CAT5 LCD CONTROL PLATFORM. 1U height, suitable for 19’’ standard cabinet installation and metal structure. 15/17/19’’ LCD screen with high brightness, high clear and high resolution. Control platform can be totally pulled out from the cabinet and the LCD screen can be turned on to 120 degrees. Ultra thin keyboard with keypad. Mouse touch board with two function button.
PAGE 5
INTRODUCTION FRONT VIEW 1 2 3 9 4 5 7 1. Front panel 2. Handle 3. LCD screen 4. Keyboard 5. Mouse touch board 6. Rear hang ear channel 7. Guide 8. Front hang ear 9.
PAGE 6
DONGLE VIEW KT-150 （PS/2 x 2） KT-250 (USB) KVM CONTROL PLATFORM POWER WIRE Wire Type AC Power Wire Note 3 Plugs of National Standard Voltage Range 100~230V AC Power Wire 6 Machine Type All
PAGE 7
DIMENSION 7
PAGE 8
CONNECTION OF KVM SIGNAL WIRE 1. Plug one end of the CAT5 UTP into the available computer port on the switch. 2. Plug the other end of the CAT5 UTP into the RJ45 port on the matching dongle. Connect the dongle to the computer. 3.
PAGE 9
OPERATION Before Use z Make sure all the devices safely grounded. z Make sure the CAT5 UTP and power wire connected correctly. During Use z z Pull the CAT5 LCD CONTROL PLATFORM out from cabinet totally, the guide locks automatically and the power turns on. Release front lock. As shown below: z Then open the front panel and the LCD can be turn on to 120 degrees.
PAGE 10
z Press LCD power key (red), the LCD is on. After Use z z z z Press LCD power key, the LCD is power off. Close LCD panel and lock the front panel. Release guide lock. Push the control panel into the cabinet totally, and then it is power off. Hot Plug The CAT5 LCD CONTROL PLATFORM supports hot plug. It can be connected and disconnected without power off. Please follow the steps: Hot plug PC connecting port: When hot plugging PC port: 1.
PAGE 11
Assembling & Disassembling The device can be assembled and disassembled as following.
PAGE 12
PAGE 13
STANDARD RACK INSTALLATION 1. Screw the front flange to the rack first. Slide the bars with the rear flange towards the rack until the flanges make contact with the rack, then screw the rear flanges to the rack. 2. Slide the switch onto the support flanges. Use the screws supplied with this package to loosely attach the front of the switch to the front of the rack. 3. Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the switch.
PAGE 14
4. Use the screws supplied with this package to attach the bars to the rear of the switch.
PAGE 15
INTERFACE SELECTION There are two ways to select: Hot key and OSD menu. HOTKEY The hotkey let the user control the connected computers by keyboard. Please check CAT5 LCD CONTROL PLATFORM user manual. FCC NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.