Robot Vacuum Cleaner User manual Basic Technical Requirements For Flat Prints Suzhou Octopus Robot Co., Ltd. Design： Date:2022.08.16 Material name User manual Size:140*210mm Material：100g Double copper paper Product number S7C-W, S7C-B Page：28 Printing color: monochrome printing Item number 0208000005 Proportion：1:1 Binding method: saddle stitching Edition V01 (08.
Model Name: S7C-W, S7C-B Laser Navigation Intelligent Robot Vacuum Cleaner User Manual Please read this instruction carefully before using the product and keep it properly.
Safety Regulations Please be vigilant and follow the following matters when using the product. Please read this manual carefully and keep it properly before using the product. Warn Notice 1. The problems that may occur during the cleaning should be eliminated in advance.Take away the power cord and small objects on the ground to prevent the product from being blocked during the cleaning process.
Instructions for disposing of batteries If you want to discard the battery in this machine, please do not throw it away along with household garbage, but hand it over to the nearest waste battery recycling station or after-sales service center for centralized disposal. The following instructions are not for general users, but for the disposal instructions of the final battery disposer. The chemical substances contained in the battery built into this unit will pollute the environment.
Sincerely thank you for purchasing the products of Suzhou Octopus Robot Co., Ltd. Hope you enjoy using it. If you encounter any problems during use, please contact our after-sales service center: +86-512-57476881, and there will be professionals to answer your questions. For more details, please visit the official website of Octopus Robot ：www.octopus-robot.
Content 4.Maintenance···················································17 1. Product Components 1.1 Packing List···································································5 1.2 Part Name·····································································6 1.3 Charge Station/Dust Box+Water tank····································7 4.1 Dust box and filter material······························17 4.2 Vacuum Port & Side Brush······························18 4.
1. Product Components / 1.1 Packing list Main Engine High-efficiency Filter Components(HEPA) Dust Box + Water Tank Charge Station and adapter Side Brush Manual *The illustrations in this manual are for reference only, and the actual appearance is subject to the actual product.
1. Product Components / 1.
1. Product Components / 1.
2.Product instruction / 2.1 matters need attention 1 Tidy up the space to be cleaned 2 and chairs, floor fans and other items neatly, and store low objects such as weight scales to organize the largest cleaning space Clean objects on the floor, such as wires, cleaning pads, slippers and other sundries, to avoid affecting the operation of the robot.
2.Product instruction / 2.2 Preparatory work 1 Remove the protective film 3 Before use, please remove the protective film on the charge station and the main machine. Install the side brush Please install the side brush into the installation opening at the bottom of the machine, and you will hear a "click", indicating that the installation is in place. Side brush Remove the protective film from the main machine.
2.Product instruction / 2.3 The main machine charge 1 Place charge station / connect to the power supply 2 Place the robot on the charge station, and pay attention to align the charging electrode. * The charge station is placed against the wall and placed on a flat ground. Do not place objects within 0.5m from left to right and 1.5m in front. * Connect the power supply. * Please arrange the power cord to avoid entanglement. 0. 0. 5M 1.
2.Product instruction / 2.4 Mode selection 1 Start cleaning In the shutdown state, press the power button of the robot. Power on in 5-10 seconds. In the power-on state, short press the power button or click the start cleaning button of the mobile App to start the automatic cleaning mode. In automatic cleaning mode, short press the power button to enter the pause state, short press the power button again to start cleaning.
2.Product instruction / 2.4 Mode selection In order to adapt to different ground conditions and achieve deep cleaning, this product has a variety of cleaning modes, which can be selected through the mobile app as needed. Smart Mode After clicking on the Smart button, the robot will perform the whole house auto cleaning. After the cleaning is completed, the sweeping robot will automatically recharge.
2.Product instruction / 2.4 Mode selection Appointment mode 1、The appointment week is set to a 7-day system (the maximum is Sunday, and Mondays etc. cannot appear); The time is set to 24H system (cannot exceed 00:60, etc.
2. Robot Operation / 2.
2. Product use / 2.6 App download and network configuration Please connect to 2.4G home Wi-Fi network Make sure that the mobile phone is connected to the Wi-Fi network available indoors, and the signal quality is good, register and login to the mobile phone. Method 2: Open the mobile application store, search for "ROBOCAT", download and install Download and install the app Method 1: Scan the QR code below, download and install the App according to the prompts.
3. Network configuration mode / 3.1 Hotspot mode • Wi-Fi hotspot network configuration(only 2.4G WIFI is supported) 1 App operation 2 Robot Operation Turn on the power switch of the robot. + Simultaneously press and hold the "Power button and recharge button" for about 3-5 seconds, until you hear the prompt tone "Wifi has been reset", the machine enters the Wi-Fi hotspot network configuration mode.
4. Maintenance / 4.1 Dust box and filter When cleaning and maintaining the robot and its accessories, please unplug the power line of charging base. Warning：The dust box and filter should not be exposed to water. 1 Take out the dust box from the back of the main unit. 2 Open the lock of the dust box and dump the trash. 4 Use the brush of the cleaning tool to clean the dust on the primary filter, paying attention to both the inside and the outside.
4. Maintenance / 4.2 Vacuum port and side brush 1 Clean the suction port If there is a lot of dust in the suction port, please use a rag to clean it. 4 2 Clean side brush Pull out the side brush and wipe it with a clean rag.
4. Maintenance / 4.3 Other components ■ Clean the anti-drop sensor to ensure the sensitivity of the sensor ■ Clean the anti-collision sensor ■ To clean the charging electrode, please use a dry rag to clean the electrode of the robot and the charging electrode of the charge station separately.
5. Light and voice alarm prompt 5.2 Voice alarm prompt 5.
6. Troubleshoot common problems During the use of the product, if the following problems occur, you can check and solve them by yourself. No 1 2 3 Troubles The robot cannot connect to the App. The robot cannot be charged. The robot automatic recharging is difficult. Cause of the troubles Solutions The router username and password are incorrect. Configure the router network and ensure that the router "username" and "password" are entered correctly.
6. Troubleshoot common problems During the use of the product, if the following problems occur, you can check and solve them by yourself. No 4 5 6 Troubles When the robot is cleaning, there are situations such as the moving route is messy, deviation, repeated cleaning, and missed cleaning in some area. The robot is in trouble while working. When the robot is working, the noise is loud.
7. Technical parameters Product number S7C-W,S7C-B Rated input voltage to robot DC24V Robot charging time Less than 6h Battery capacity Operating time Dust box capacity Water tank capacity Fan suction Rated input voltage of charge station Rated output voltage of charge station Lithium battery 2600mAh About 90 minutes 250ml 300ml 4200Pa(maximum) AC220-240V 24V Rated input power Rated output current 18W 1.
Name of harmful substance Harmful materials Parts category Lead (Pb) and its compounds Mercury (Hg) and its compounds Cadmium (Cd) and its compounds Hexavalent chromium (Cr(VI)) and its compounds Polybromin ated biphenyls (PBB) Plastic parts Metals hardware Robot circuit module Electronic Component Battery Plug power cord (metal part) Note: This table is compiled in accordance with the provisions of SJ/T 11364.
Product After-sales Service Card • Return and exchange receipt China after-sales service hotline： In order to better protect your legal rights and handle the return or refund business conveniently, please fill in accurately and completely. Customers who purchase offline do not need to fill in the form below.
FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
