JM-C3-7000 intelligent charger User manual v1.0 SUZHOU EAVISION ROBOTIC TECHNOLOGIES CO.
To Users Thank you for choosing JM-C3-7000 series fully intelligent chargers carefully developed and manufactured by SUZHOU EAVISION ROBOTIC TECHNOLOGIES CO., LTD(here in after referred to as "EAVision"). In order to familiarize you with the operation and maintenance of the device, please read and comply with the relevant requirements of this manual carefully.
To Users ............................................................................................................................................ 2 Disclaimers .......................................................................................................................................4 Product overview ........................................................................................................................... 5 Introduction .......................................................
Disclaimers Please read this statement carefully before using this product. The use of this Product is deemed to be the approval and acceptance of the entire contents of this Statement. This product is not suitable for people under 18 years old. Prior to using this product, please receive regular training from EAVision and obtain an unmanned aerial system operating license approved by EAVision . Keep this product away from children and be careful when operating in the presence of children.
Product overview Introduction JM2-29000mAh intelligent battery is equipped with JM-C3-7000W intelligent charger, which can be filled with a battery in about 11 minutes. The conventional standard operation time of UAV is 10-12 minutes, and the operation time can cover the charging time, realizing "two battery and one charger, easy circulation". The maximum charging power of the charger is up to 7000W, and it can be connected to the charging management App through Bluetooth.
Charge controller Battery status indicator The LED corresponds to the charging status of the inserted channel battery 1. Blinking yellow: The battery is inserted； 2. Blinking green: The battery is being charged 3. Steady green: The battery is fully charged； Bluetooth indicator light The LED indicate Bluetooth connection 1.The blinking green light indicates the search status, and there is no link to the APP; 2.
2.Steady red indicates that charging control module is faulty; If the warning light is red,please stop charging immediately and check the alarm information of the APP.The charging can be continued only after the abnormality is eliminated and the red light is off. Precautions for use 1. AC power input port and generator plug with high voltage ,do not touch. 2.Charger belongs to the product of large leakage current ,before the use of power,must connect the ground wire, to ensure reliable grounding. 3.
9. Do not plug or remove the battery when it is charged, Otherwise, a charging fault will occur, if the yellow light of the battery controller is steady on.
Usage of Charger Check before use appearance inspection 1. Check whether the charge controller and power input cable are damaged, that all cable is normal. 2. Check whether the charging controller pin is deformed 3. Check whether the generator power supply line and socket are damaged ,deformed, or blocked by foreign bodies Check after power on 1. Check whether the fan works properly after it is connected to the power supply. 2.
Use 1. The charger must be well grounded when in use. Please use a grounding wire to ground the shell of the charger. Remove the screw of the grounding interface and fix the grounding wire, as shown in the figure below. 2. Connecting the charger to household electricity or a generator. 3. Insert the charging cable connector into the battery to start charging. The AC end of the charger is equipped with two power input sockets.
Do not plug the battery into the charger during the charger upgrade. Do not cut off the power and keep your device away from the charger during the upgrade. If the upgrade fails,try again. Storage and Maintenance 1. When the charger is charged finish or not in use, disconnect the battery charging cable from the charger, disconnect the power cable, and fix the battery charging cable and controller to the fixed position for stability protection. 2.
7. In case of fire, please use the dry chemical extinguisher correctly to extinguish the fire, The use of liquid extinguishers may cause the danger of electric shock. 8. Forbid to insert any non-EAV battery for charging ,Do not unplug the power cord during charging ,after charging, remove the battery in time. 9. Do not plug or remove the battery when it is charged, Otherwise, a charging fault will occur, if the yellow light of the battery controller is steady on.
Please Follow EAVISION Official Social Media Channel： YouTube，Facebook，Twitter，LinkedIn,Instagram The contents of this manual and product specifications are subject to change without prior notice. Suzhou EAVISION Robotic Technologies Co.,Ltd. Address: Unit1-A, No.3 Workshop, 28 Xiasheng Road, SIP, Suzhou, Jiangsu Province, China Website：www.eav.
