Eavsion RTK Basise Station User Mannual V2.0/2022.08 EA-BAS20 SUZHOU EAVISION ROBOTIC TECHNOLOGIES CO., LTD Address: Unit 1-A, No.3 Workshop, 28 Xiasheng Road, SIP, Suzhou, China Website: www.eav.
FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Table of Contents Disclaimer ....................................................................................................................................................................... 4 Precaution .......................................................................................................................................................................4 Product Overview ....................................................................................................................
Disclaimer Thanks for choosing the EA-20XA (global offline version) developed and manufactured by Suzhou EAVISION Robotic Technologies Co., Ltd. (hereinafter referred to as "EAVISION"). Please read and abide by the relevant requirements of this manual carefully, operate in strict accordance with the instructions in actual operation process and maintain in a timely and detailed manner. The use of this product shall be deemed as the approval and acceptance of the entire contents of this manual.
Product Overview Brief Introduction EA-20X realizes the data transmission between the UAV and the ground station through the 4G signals. In some areas with the weak or no 4G signals, the UAV fails to receive mission data from the ground station and cannot operate autonomously. EA-20XA-global offline version connects all the devices in the system to realize the autonomous operation in offline state via the mobile base station and surveying tool. Introduction to module 1. GPS antenna 2.
antenna 9. Alarm red indicator 10.Positioning/differential 11. Wifi/Bluetooth indicator 12. Ground wire 17.Base station back cover 18.Base station indicator 13. Power indicator 14. Debugging back cover 15.Charging charging port 16.Fixing screw instruction nameplate Operation instruction Base station erection instructions Place the base station on a tripod with its own screws and place it in an open space outdoors.
How to check the remaining power Lightly press the indicator button on the power display panel, the corresponding power indicator lights up, and automatically turns off after 2 seconds. The remaining power value can be read by the LED light on and off. 1. Four green LED lights are on, indicating that the base station is at 100% power at this time 2. The three green LED lights are on, indicating that the remaining power of the base station is 75% at this time 3.
Batt1+Batt2+Batt3 is always on for 3s, and goes out after 3s; (2) When charging: the corresponding battery bar flashes, and the fully charged battery bar is always on. For example: when charging 50%
positioning or enter the differential mode according to the time-limited positioning (10min backward differential) conditions. Positioning LED flashes: a. When the remaining time is less than 2min, the positioning LED light flashes: 0.5s on, 0.5s off; b. When the remaining time is less than 2min, the positioning LED light flashes: 0.5s on, 0.5s off; c. Remaining time >5min, positioning LED light: 1.7s on, 0.
Operation Steps Preparation before use Please log in EAVISION Surveying APP and EAV Smart Agriculture APP before entering the area with no network. Enter the operation area and erect the base station in the appropriate positions. Turn on all the devices in the offline system. Check base station state Enter the EAVISION Surveying APP. Click the left sidebar on the main screen to open the menu bar. Click the “Enter offline mode” and then click on “Mapping Equipment Connect”.
After the connection of surveying tool, the base station is connected automatically.
Appendix Product parameters Standby time 10-12 h Charging time 4-6 h weight 2380 g size 700*185*140 mm coverage 10 km Working accuracy 1-10 cm Input voktage/frequency 100-240V~50/60hz Output voltage 5V-3A/9V-2A/12V-1.
Warry Certificate EAVISION Robotics Technologies Warranty Certificate （Customer） Product Name Autonomous Plant Protection Drone Model Product Specification Information Manufactured In Suzhou, China Serial Number Name Address Phone Number Email Sales Unit Address Sales Contact Number Email Information Sales Date Unit Price Invoice Number Sales Unit Stamp Manufacturer Manufacturer Name Address Information Phone Number Email User Information Maintenance Delivery Failure Repair Dat
Please Follow EAVISION Official Social Media Channel： YouTube，Facebook，Twitter，LinkedIn,Instagram The contents of this manual and product specifications are subject to change without prior notice. Suzhou EAVISION Robotic Technologies Co.,Ltd. Address: Unit1-A, No.3 Workshop, 28 Xiasheng Road, SIP, Suzhou, Jiangsu Province, China Website：www.eav.
