User's Manual
Table Of Contents
- 1. GENERAL INFORMATION
- 1.1. CHECKLIST
- 1.2. suunto t6 features
- 1.3. CARE AND MAINTENANCE
- 1.4. WATER RESISTANCE
- 1.5. REPLACING THE BATTERY
- 1.6. replacing the battery of the transmitter belt
- 1.7. heart rate transmitter belt
- 1.7.1. Activating the heart rate transmitter belt
- 1.7.2. Warnings
- 1.8. wireless speed and distance sensors
- 1.8.1. Activating the wireless speed and distance sensor
- 2. HOW TO USE YOUR SUUNTO t6
- 2.1. DISPLAY AND BUTTONS
- 2.1.1. Mode indicator
- 2.1.2. Battery level indicator
- 2.1.3. Alarm symbols
- 2.1.4. Key Lock
- 2.2. MENUS
- 2.2.1. Basic menu structure
- 2.2.2. Press and long press
- 2.2.3. Navigating in the menus
- 3. MODES
- 3.1. GENERAL INFORMATION
- 3.2. time mode
- 3.2.1. Main display
- 3.2.2. Alarm
- 3.2.3. Time
- 3.2.4. Date
- 3.2.5. General
- 3.2.6. Units
- 3.3. alti/baro mode
- 3.3.1. Use (Alti/Baro)
- 3.3.2. Alti use
- 3.3.3. Baro use
- 3.3.4. Reference altitude and barometric pressure
- 3.3.5. Memory
- 3.4. training
- 3.4.1. Stopwatch
- 3.4.2. Connect
- 3.4.3. Logbook
- 3.4.4. HR limits
- 3.4.5. Timers
- 3.4.6. Refer
- 3.4.7. History
- 3.4.8. Pair
- 3.4.9. Use (Alti/Baro)
- 3.5. SPD/DST mode
- 3.5.1. Main display
- 3.5.2. Connect
- 3.5.3. Autolap
- 3.5.4. Distance intervals
- 3.5.5. Speed limits
- 3.5.6. Calibrating wireless speed and distance sensor
- 3.5.7. pair
- 4. Using suunto t6 in training
- 4.1. Using HR and speed limits in training
- 4.2. making the most out of your training
- 5. suunto training MANAGER
- 5.1. System requirements
- 5.2. Installation
- 5.2.1. Installing Suunto Training Manager
- 5.2.2. Installing USB drivers for Suunto sport instruments
- 5.3. Suunto Training Manager features-ULLA
- 5.4. Uninstalling USB drivers for Suunto sport instruments
- 6. SUUntosports.com
- 6.1. GETTING STARTED
- 6.2. SECTIONS
- 6.3. My Suunto
- 6.4. Communities
- 6.5. Sport Forums
- 7. technical specifications
- 8. disclaimers
- 8.1. user’s responsibility
- 8.2. copyright, trademark and patent notice
- 8.3. ce
- 8.4. limits of liability and iso 9001 compliance
- 8.5. after sales service
- 8.6. disclaimer
45
Removing the battery, shortcutting the transmitter belt and putting the battery back
again activates the ID transmission of the transmitter belt.
NOTE: The transmitter belt is already paired with the device when it leaves the fac-
tory. However, if you use either another device or transmitter belt or if you encounter
problems with the heart rate measurement, you need to pair it again.
Wireless speed and distance sensor
To pair the wireless speed and distance sensor:
1. Select Pair in the Training menu.
2. Select SPD SENS. The message ‘
TURN ON NEW DEVICE’ is displayed.
3. Turn the wireless speed and distance sensor on. After 30 seconds either ‘
PAIRING
COMPLETE
’, or, if pairing failed, ‘NO DEVICES FOUND’ is displayed.
NOTE: You can only connect one wireless speed and distance sensor at a time.
3.4.9. Use (Alti/Baro)
With this function you can select whether altitude information is recorded in the
logbook memory with other information. Refer to section 3.3.1 Use (Alti/Baro).