Instructions / Assembly

ManualsBrandsSureSill ManualsDoors & Windows4-1/8 in. x 150 in. Sloped Sill Pan for Door and Window Installation and Flashing (Complete Pack)

SURESILL WATER MANAGEMENT GUIDE

FOR WINDOWS AND DOORS

pyright 2004

2010

2016

SureSill, Ltd. All rights

reserved.

HEADFLASH ASSEMBLY

Measure the exterior width of the window/door, including any brick

mold, and cut the DrainShield

to that measurement. Check fit with

end caps before gluing. Remove any labels from contact surfaces.

Apply Wet-R-Dry

PVC cement to contact

surfaces on both End Caps and

DrainShield

(shaded area).

Slide End Caps fully in

place. Wipe excess PVC

cement. Hold glued parts

for 1 min for PVC cement

to dry.

Check the fit with end caps before gluing them. See Sill

Pan Assembly DETAIL on page 3.

Weep Holes

SureSill

Channel Plate

End Cap

SLOPED SILL PAN ASSEMBLY

Apply Wet-R-Dry

PVC cement to contact

surfaces on both End Caps and Channel Plate

(shaded area).

Slide End Caps fully in

place. Wipe off excess

PVC cement.

Page 1 of 3

SAF Henkel/OSI BUTYLFLASH;

SEALANT Henkel/OSI® QUAD®MAX LOW EXPANSION FOAM QUAD®FOAM by Henkel/OSI®

RECOMMENDED

PRODUCTS

Summary of content (5 pages)

PAGE 1
SURESILL WATER MANAGEMENT GUIDE FOR WINDOWS AND DOORS*1 SLOPED SILL PAN ASSEMBLY HEADFLASH Measure the exterior width of the window/door, including any brick mold, and cut the DrainShieldTM to that measurement. Check fit with end caps before gluing. Remove any labels from contact surfaces. Check the fit with end caps before gluing them. See Sill Pan Assembly DETAIL on page 3.
PAGE 2
THE SURE LEVEL OF PROTECTION *1 STEP 1 Install Drainage Skirt plate over any sub-floor area. See Sealing the Sill Pan STEP 1 DETAIL STEP 2 Install assembled SureSillTM Sloped Sill rough opening, and secure to rough opening by fasteners in slots provided. STEP 3 Use self adhering flashing (SAF) on rough jamb, over SureSillTM End Caps. Apply adhesive sealant to jambs and head. Apply sealant on concrete, sub- floor or the sides. water-proofing (SAF or similar) plate and over any sub-floor area.
PAGE 3
*1 Installation Details SILL PAN ASSEMBLY Sealing the Sill Pan to WRB STEP 1 DETAIL - Seal the front lip of the Sill Pan to WRB or to Drainage Skirt. Seal between the sill pan and the rough opening on the sides as indicated. This should provide a barrier against both moisture and air infiltration between the sill pan and the FRONT SIDE BACK SIDE DETAIL REMOVE LABELS FROM CONTACT SURFACES. AS PART OF THE SILL PAN ASSEMBLY APPLY SEALANT ALONG THE EDGE OF END CAP.
PAGE 4
EXTERIOR DOOR SOLUTIONS EXTERIOR DOOR DRAIN DETAIL 1. STEP DOWN LANDING SURESILLTM Sloped S RECOMMENDED Door Door Sill Finish Floor Sealant Joint Sloped Masonry Veneer Minimum CONCRETE OR SUBFLOOR Mortar Joint DEDICATED DRAIANGE PATH - FOR PROPER DRAINAGE BEHIND MASONRY USE RAIN SCREEN SUCH AS ENKADRAIN 9010® BY COLBOND, Inc. APPLY 2 WIDE STRIPS 12 O.C. Landing Tiles or other finish surface Fig.
PAGE 5
2. CONTINUOUS SLAB (ON-GRADE) EXTERIOR DOOR DRAIN DETAIL INCLUDING ADA DOORS Exterior Surface - Sloped Landing Fig. 2 CONTINOUS SLAB EXTERIOR DOOR DRAIN DETAIL Deck Drain should be installed to evacuate the water with an open end away from the building. Exterior Surface should slope away from the building. Install SureSil System per SureSill Water Management Guide Recommended products for Deck Drain: Super Drain by Stegmeier Corporation http://www.stegmeier.com/index.