Manual

ManualsBrandsSurefire ManualsFirearm Accessories9an

John Matthews

President, SUREFIRE

9AN

COMMANDER

POWERSELECT

Congratulations, with the purchase of this

SUREFIRE flashlight, you have invested in

one of the world’s best “illumination tools.”

We believe it to be a prime example of

our philosophy that design decisions should

always be made in the interest of the product

being the very best it can be.

Frequently, this means deciding to use a

more costly process or a more expensive ma-

terial than would normally be called for. We

know that in order to produce the best, one

must do it right.

We thank you for supporting this deci-

sion and electing to confirm our belief in “no

compromise” in a product that, by its perfor-

mance and reliability, may some day be called

upon to save your life.

There is no other choice.

20/140 Lumens

Summary of content (11 pages)

PAGE 1
POWERSELECT TM 9AN COMMANDER TM 20/140 Lumens Congratulations, with the purchase of this SUREFIRE flashlight, you have invested in one of the world’s best “illumination tools.” We believe it to be a prime example of our philosophy that design decisions should always be made in the interest of the product being the very best it can be. Frequently, this means deciding to use a more costly process or a more expensive material than would normally be called for.
PAGE 2
WELCOME TO THE SUREFIRE TEAM You have just become the owner of one of the most incredible pieces of lighting technology ever conceived. It is a masterpiece of engineering, a member of the SUREFIRE family which has gained the acceptance and respect of military and law enforcement professionals around the world. SUREFIRE lights provide overwhelming power, and they do this with a quality of beam that is unmatched in brilliance and performance.
PAGE 3
THE 9AN COMMANDER The 9AN Commander Rechargeable Flashlight is a masterpiece of engineering. This is a one-of-a-kind, high performance unit that does the job of two flashlights. Simply rotate the 9AN head to choose one of two power settings; one projects a low, soft 20 lumen light for close-up activities such as report writing, and the other level gives you a brilliant, high-power 140 lumen beam with the intensity to temporarily blind an attacker.
PAGE 4
9AN COMMANDER There are two ways to activate the light from the 9AN. The Tail Cap switch of the Flashlight can be activated by rotating the Tail Cap in a clockwise direction for a constant “ON” setting or by pressing on the Push Button for temporary light.
PAGE 5
SPECIFICATIONS Power Output Run Time Battery Type Number Required Supplied Length Weight Diameter Lamp Assembly Lens ON/OFF Switch Power Output Selection Switch Body Material Finish Color Water Resistant 20/140 Lumens - N90 20 lumens - 120 Minutes 140 lumens - 40 Minutes Ni-Cd One (1) Yes 7.9 inches 12.9 ounces Body - 1.28 inch Bezel -1.
PAGE 6
PARTS REPLACEMENT LIST Component Part No. Battery - Nc-Cd B90 Bezel Assembly 13270 Flashlight Body 14108 Lamp Assy Lens N90 11956-1 O-Ring Seal (rear) 19-01-040 O-Ring Seal (front) 19-01-023 Lock Out Tail Cap Assy 12708 WARNING The Reflector Body is vented for use with Ni-Cd batteries. Ni-Cd batteries can release combustible gasses during discharge. In a sealed battery compartment these gases could buildup and might damage the battery or even cause injury to the user.
PAGE 7
9AN COMMANDER O-RING (front) VENT BEZEL ASSEMBLY LAMP ASSEMBLY BODY BATTERY TAIL CAP ASSEMBLY PUSH BUTTON (hidden) O-RING (rear)
PAGE 8
CHANGING THE LAMP 1. Remove the Flashlight Head from the Flashlight Body by holding the Head and rotating the Body counterclockwise (as viewed from the tail of the Flashlight) until it is free of the Head. 2. Remove the Nylon Screw that is securing the Lamp Assembly to the Bezel. 3. Remove the inoperative Lamp Assembly and replace with the new N90 Lamp Assembly. Avoid touching the inside of the Lamp envelope as this will degrade the performance of your SUREFIRE Light. 4.
PAGE 9
INSTALLING THE BATTERY 1. Remove the Flashlight Tail Cap by unscrewing it until it is free of the Flashlight Body. 2. Insert the B90 Ni-Cd Battery, observing proper battery polarity, into the Flashlight Body. 3. Install the Flashlight Tail Cap back on to the Flashlight Body by turning it until the light comes on. Then back off 1/2 to 1 turn until the light turns off. 4. The 9AN Commander is now ready for use. Be sure to charge the battery before first use.
PAGE 10
SELECTING POWER LEVEL The 9AN Commander has two seperate lamp assemblies within the bezel reflector. When operating on the general use beam of 20 lumens only one lamp assembly is activated. For the high power 140 lumen beam both lamp assemblies are activated For 140 Lumen Beam While holding the Head of the 9AN, turn the Body of the 9AN clockwise until it is fully screwed into the Head. The High Power beam will be turned on when the Tail Cap switch is activated.
PAGE 11
CUSTOMER SERVICE REPAIRS AND REPLACEMENTS To obtain repair or replacement contact Customer Service at 800-828-8809 (toll free) or 714-545-9444 and obtain a Return Authorization number (RA#). Then package the unit carefully and return (no COD’s please) to: SUREFIRE LLC Repairs Department, RA# ___ 18300 Mt. Baldy Circle Fountain Valley, CA 92708 SUREFIRE will pay any reasonable shipping costs to return the unit to you. Protected by U.S.