User's Manual

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [e-mail]
98
Installing your Hardware
Booster Hardware
The following image shows the key hardware components on the cellullar booster.
Refer to this image as you install your Force5 Inline kit components.
DIP Switches and Lights
The Force5 Inline Industrial booster has the following indicators and controls:
• PCS Uplink Warning light/DIP switches (1): These DIP switches control the PCS communications
with the cellular tower.
• PCS Downlink Warning light/DIP switches (2): These DIP switches control the PCS amplication
within the building.
• Power light (3): This light should be illuminated or blinking green at all times while the booster is
powered on.
• Cellular Downlink Warning light/DIP switches 4): These DIP switches control the cellular
amplication within the building.
• Cellular Uplink Warning light/DIP switches (5): These switches control the cellular communications
with the tower.
Power LED
N connector to inside antenna
N connector to outside antenna
Alert LED
Power Switch
Programmer
Power Jack
Mount Kit
Step 3. Congure Gain Settings
Facing the front of your booster, nd 9 banks of Dual In-line Package (DIP) switches.
These switches allow manual dB gain attenuation for uplink and downlink channels.
• Bank 1 controls AT&T communications with the cellular tower.
• Bank 2 controls Verizon and AT&T amplication in the building.
• Bank 3 controls Verizon communications with the cellular tower
• Bank 4 controls Cellular communications with the cellular tower.
• Bank 5 controls Cellular amplication in the building.
• Bank 6 controls PCS amplication with the cellular tower.
• Bank 7 controls PCS amplication in the building.
• Bank 8 controls T-Mobile communications with the cellular tower.
• Bank 9 controls T-Mobile amplication in the building.
The DIP switches in each bank correspond to the following dB gain values:
For maximum gain on all channels, your booster ships with all DIP switches turned OFF.
This setting should always be your starting point when installing or reinstalling the booster.
To change it, move the DIP switches to the ON or OFF position.
• Moving a switch down (away from the LEDs) turns OFF the switch and increases
booster gain for the selected channel.
• Moving a switch up (toward the LEDs) turns ON the switch and decreases booster
gain for the selected channel.
Switch settings are cumulative. This means the total amount of attenuation for a channel
equals the combined dB of all DIP switches in the same bank being set to ON.
Installing Your Hardware
1 2 3
4
5
ON DIP
1 2 4 8 16
LTE707-UL
LTE-707 LTE-781
1 2 3
4
5
ON DIP
1 2 4 8 16
LTE-DL
1 2 3
4
5
ON DIP
1 2 4 8 16
LTE781-UL
1 2 3
4
5
ON DIP
1 2 4 8 16
CELLULAR-UL
Cellular-800
1 2 3
4
5
ON DIP
1 2 4 8 16
CELLULAR-DL
1 2 3
4
5
ON DIP
1 2 4 8 16
PCS-UL
PCS-1900
1 2 3
4
5
ON DIP
1 2 4 8 16
PCS-DL
1 2 3
4
5
ON DIP
1 2 4 8 16
AWS-UL AWS-DL
AWS-2100
1 2 3
4
5
ON DIP
1 2 4 8 16
Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9
Switch1
1 dB
Switch2
2 dB
Switch3
4 dB
Switch4
8 dB
Switch5
16 dB
WARNING: Do not adjust the uplink and downlink dB attenuation settings more than 20dB.
This could cause the booster to shut down
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [e-mail]