User's Manual

ManualsBrandsSureCall ManualsElectronics5-band signal booster

Force5 Inline

5-Band Cellular Booster Extender for Commercial

Oces, Institutions and Housing Complexes.

User Guide

This is NOT a CONSUMER device. It is designated for installation

by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST

have an FCC LICENSE or express consent of an FCC Licensee to

operate this device. Unauthorized use may result in signicant

forfeiture penalties, including penalties in excess of $100,000

for each continuing violation.

WARNING

Summary of content (9 pages)

PAGE 1
Force5 Inline 5-Band Cellular Booster Extender for Commercial Offices, Institutions and Housing Complexes. User Guide WARNING This is NOT a CONSUMER device. It is designated for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation.
PAGE 2
How it Works Table of Contents How It Works Pg. 3 Package Contents Pg. 4 Before You Start Pg. 4 Installing Your inside Antenna Pg. 5 Installing Signal Booster Pg. 7 Configure Gain Setting Pg. 9-11 Troubleshooting Pg. 12 Specification Pg. 13 Warranty Pg. 14-15 Safety Information 2 SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com Pg. 15 Thank you for your purchase of the Force5 Inline signal booster.
PAGE 3
Package Contents Installing Your Hardware 1. Unpack all package contents. For missing or damaged items, contact your reseller. Step 1. Install the Inside Antenna 2. Turn over the signal booster and record the model and serial number for reference: Inside antennas come in omni-directional (dome) and flat panel versions. Serial #: Purchase Date: Required Between Outside and Inside Antenna n atio par e s a enn ant 3.
PAGE 4
Installing Your Hardware Dome antennas are omni-directional interior antenna that gather signals from all sides. Range of antennas is dependent on three factors: 1) Physical obstructions 2) Power generated by booster and 3) Reception from outside signal received and distributed by outside antenna. Dome antennas should be mounted in an upright position for best results. Step 1: Drill a 35mm diameter hole in the ceiling. The ceiling thickness should be 20mm, maximum.
PAGE 5
Installing Your Hardware Installing your Hardware Booster Hardware Step 3. Configure Gain Settings The following image shows the key hardware components on the cellullar booster. Refer to this image as you install your Force5 Inline kit components. Facing the front of your booster, find 9 banks of Dual In-line Package (DIP) switches. These switches allow manual dB gain attenuation for uplink and downlink channels. • Bank 1 controls AT&T communications with the cellular tower.
PAGE 6
Installing your Hardware To Achieve... Installing Your Hardware Set the DIP Switchs in the Same Bank as Follows...
PAGE 7
Troubleshooting Specifications In the event you encounter a problem, follow the suggestions below to resolve the issue. Problem Resolution Signal booster has no power Verify that the booster switch is turned on. Connect the power supply to an alternate power source. Be sure the AC outlet is working and is not controlled by a wall switch that can cut power to the outlet. If the green POWER LED on the signal booster is OFF, return the power supply to SureCall.
PAGE 8
Warranty Warranty Three-Year Product Warranty SureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials. Specifications are subject to change. The three-year warranty only applies to products meeting the latest FCC Certification Guidelines stated on 2/20/2013 and going into effect April 30, 2014. A two-year warranty applies to any products manufactured before May 1, 2014.
PAGE 9
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.