Installation Instructions
MATERIAL SAFETY DATA SHEET
Page 4 of 6
1,3 Pentadiene, Polmer with
2-Methyl-2-Butene
26813-14-9
Not Listed
Not Listed
Not Listed
None
Heavy Hydrotreated
Naphthenic Distillates
64742-52-5
5 mg/m Mist
5 mg/m Mist
5 mg/m Mist
5 mg/m Mist
Currently, International exposure limits are established for the components of this product. Please check with competent
authority in each country for the most recent limits in place.
The following information on appropriate Personal Protective Equipment is provided to assist employers in complying with
OSHA regulations found in 29 CFR Subpart I (beginning at 1910.132) or equivalent standard of Canada, or standards of EU
member states (including EN 149 for respiratory PPE, and EN 166 for face/eye protection), and those of Japan. Please
reference applicable regulations and standards for relevant details.
RESPIRATORY PROTECTION: When thermal processing fumes are generated and ventilation is not sufficient to effectively
remove them appropriate approved respiratory protection must be provided. Heated product will emit vapors and exposed
workers may need to use a NIOSH approved, organic vapor canister type respirator. If necessary, use only respiratory
protection authorized in the U.S. Federal OSHA Respiratory Protection Standard (29 CFR 1910.134), equivalent U.S. State
standards, Canadian CSA Standard Z94.4-93, the European Standard EN149, or EU member states. Oxygen levels below
19.5% are considered IDLH by OSHA. In such atmospheres, use of a full-facepiece pressure/demand SCBA or a full
facepiece, supplied air respirator with auxiliary self-contained air supply is required under U.S. Federal OSHA’s Respiratory
Protection Standard (1910.134-1998) or the regulations of various U.S. States, Canada, EU Member States, or those of
Japan. Air-purifying respirators with dust/mist/fume filters are recommended if operations may produce mists or sprays from
this product.
EYE PROTECTION: Wear chemical goggles, face shield if handling molten material. If necessary, refer to U.S. OSHA 29
CFR 1910.133, Canadian Standards, and the European Standard EN166, Australian Standards, or relevant Japanese
Standards.
HAND PROTECTION: Wear thermal insulating gloves to protect from thermal burns. If necessary, refer to U.S. OSHA 29
CFR 1910.138, the European Standard DIN EN 374, the appropriate Standards of Canada, Australian Standards, or
relevant Japanese Standards.
BODY PROTECTION: Work clothing sufficient to prevent skin contact. If necessary, refer to appropriate Standards of
Canada, or appropriate Standards of the EU, Australian Standards, or relevant Japanese Standards.
9. PHYSICAL and CHEMICAL PROPERTIES
SOFTENING POINT: 176° - 212°F (80° - 100°C) EVAPORATION RATE (n-BuAc=1): Not Applicable
SPECIFIC GRAVITY @ 20C: 0.939 (water=1) SOLUBILITY IN WATER: Non soluble
VAPOR PRESSURE, mm Hg @ 20°C (68F): NA pH: NA
ODOR THRESHOLD: No odor
APPEARANCE, ODOR and COLOR: This product is a clear to opaque white to light amber solid with no odor.
10. STABILITY and REACTIVITY
STABILITY: Stable.
DECOMPOSITION PRODUCTS: Thermal degradation produces carbon monoxide, carbon dioxide and/or low molecular
weight hydrocarbons.
MATERIALS WITH WHICH SUBSTANCE IS INCOMPATIBLE: The product may react to strong acids and oxidizing agents.
POSSIBILITY OF HAZARDOUS REACTIONS: Will not occur.
CONDITIONS TO AVOID: Avoid excessive overheating. Do not add water or other volatile material to molten adhesive.
11. TOXICOLOGICAL INFORMATION
TOXICITY DATA:
No LD50 Data Available for this product
SUSPECTED CANCER AGENT: The components of this product are not listed by agencies tracking the carcinogenic
potential of chemical compounds as follows:
Carcinogenity
NTP Regulated
No
IARC Regulated
No