NOVUS INSTALLATION GUIDE Version 1.01 English EN 101.00.NVS07_D1/NVS07_D1K V1.
Contents Safety instructions ................................................................................. 4 Introduction ............................................................................................ 5 Components ...................................................................................................................................................5 Basic Components.................................................................................................................
Copyright notice ..........................................................................................................................................31 Open Source License ....................................................................................................................................31 GNU GENERAL PUBLIC LICENSE........................................................................................................................................31 BoringSSL License ...............
Safety instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance with instructions can lead to serious injury or death. Installation Do not install the product in a location with direct sunlight, moisture, dust, or soot. • Fire or electric shock may occur. Do not install the product in a location with heat from an electric heater. • Fire or electric shock may occur due to overheating.
Introduction Suprema NOVUS is a multimedia workstation designed to support any Time and Attendance or Workforce Management application. NOVUS provides an up-to-date development, feature-rich environment that allows partners and integrators to integrate and extend the functionalities of their existing applications using the powerful integrated capabilities of the system.
Optional Components You can assemble the various options you need into NOVUS. For more information on how to install each option, refer to Installing the Optional Part in this guide.
Disassembling the device housing Disassembling the rear cover To assemble or disassemble some optional parts and connect cables, you need to separate the rear cover. 1 2 3 Unlock the device with the key and open the rear cover of the device. 4 Pull out the latch of the right side and disassemble the rear cover from the housing completely. Unplug one side of the cable and strap that are connected to both the rear cover and the housing side.
Disassembling the housing To assemble some optional parts, you need to separate the housing. 1 Unplug one side of the cable that is connected to both the front and back of the housing. If a magnetic swipe reader is mounted on the device, you need to unplug the MSR module cable. 2 Loosen the four screws on the back of the housing. 3 Disassemble the front and back of the housing.
Name and function of each part Front Camera RF card Authentication Unit Microphone LED indicator Magnetic Swipe Reader LCD Touch screen Keypad Fingerprint Authentication Unit Speaker External USB slot Name Description Camera Captures actual images. Microphone Delivers the voice of the user when using some application such as Phone, Sound Recorder, etc. LED Indicator Indicates the operational status of the device with the color of the LED.
Name of each part Housing No.
14 Keyboard Cable Connector 15 Speaker Cable Connector 16 Fingerprint Sensor Mounting Area 17 Fingerprint FFC Connector 18 Fingerprint Cable Connector 19 RFID Module Mounting Area 20 RFID Module Cable Connector 21 Modem Power Cable Connector 22 GPS Module Connector Rear Cover No.
Installation Fixing the device 1 2 3 Disassemble the housing and the rear cover of the NOVUS by referring to Disassembling the device housing. 4 Mount the rear cover on the screws fixed to the wall. 5 Fix the rear cover firmly using the two fixing screws at the lower part. Determine the correct position to install the NOVUS using the provided drilling template. Screw the two fixing screws first at the upper screw position of the drilling template.
NOTE • • 6 If installing NOVUS on a concrete wall, drill holes, insert PVC anchors, and attach them with fixing screws. If you use the RFID option, to avoid RF interference, a minimum separation distance must be maintained. The minimum separation distance of NOVUS is 10 cm from the horizontal plane and 10 cm vertically. Install the housing onto the rear cover.
Installing the basic part Power supply 1 2 Unlock the device with the key and open the rear cover of the device. Connect the power cable to the Power Connector. NOTE • Use a power supply adaptor of DC 12 V with a minimum of 2,140 mA which has obtained the approval of IEC/EN 60950-1.
Battery The backup battery can be used to prevent power failure. 1 2 Unlock the device with the key and open the rear cover of the device. 3 Connect the battery cable to the battery connector on the battery board and the main board. Mount the batteries into the battery holder. Make sure to observe the correct battery polarity when installing. NOTE • • • • • When installing batteries with DC or POE power supplied, NOVUS may take up to a few minutes to detect batteries for accurately and safely charge.
Relay You can control the door by connecting the relay to the NOVUS. Use the SVP Android SDK, you can apply the feature to control the relay to your application. NOTE • • Relay cable is sold separately. You can view the SVP Android SDK at http://kb.supremainc.com/svpsdk. Wiegand NOTE • Wiegand cable is sold separately.
Installing the Optional Part You can assemble the various options you need into NOVUS. This section describes how to mount each option to NOVUS. NOTE • • Before installing the optional parts, turn off the power and PoE on the device, and remove the batteries. To more information on optional parts supported by NOVUS and how to purchase them, please visit https://support.supremainc.com and contact to Suprema Tech Team.
5 Hold the FCC with the blue side up connect it so that the outer dotted outline contacts the holder of the FCC connector. 6 Close the holder of the FCC connector to lock the cable in place. 7 Connect the fingerprint cable to the fingerprint cable connector. NOTE • For more information on how to enroll the fingerprints, please refer to How to enroll a fingerprint correctly.
RFID Module 1 2 Disassemble the front and back of the housing by referring to Disassembling the housing. 3 Fix the RFID module firmly at the housing using the two screws. 4 Connect the RFID cable to the RFID module cable connector. Place the RFID module on the RFID module mounting area.
MSR (Magnetic Swipe Reader) 1 2 Disassemble the front and back of the housing by referring to Disassembling the housing. 3 Insert the MSR module cable into the hole in the housing side and mount the reader on the housing. 4 Fix the magnetic swipe reader firmly at the housing using the two screws. 5 Connect the MSR module cable to the MSR module cable connector. Loosen the two screws on the inside of the housing side and disassemble the cover.
GPS 1 2 Disassemble the front and back of the housing by referring to Disassembling the housing. 3 Connect the GPS module cable to the GPS module cable connector. Attach the GPS module to the GPS module adhesion area using double-sided tape. Wireless Ethernet 1 2 Unlock the device with the key and open the rear cover of the device. Plug the WiFi Dongle in to the top of the internal USB slot.
Cellular Modem 1 2 Unlock the device with the key and open the rear cover of the device. 3 Mount the lower part of the bracket into the modem mounting area of the rear cover and mount the upper part. 4 Fix the modem bracket firmly at the rear cover using a screw. Insert the cellular modem into the modem bracket from the top first and attach it using a double sided tape.
5 Connect the modem antenna to the cellular modem. NOTE • Connect the modem antenna to the side of the antenna connector on the cellular modem. 6 Attach the modem antenna to the modem antenna adhesion area. The internal antenna may be omitted if the site requires use of a remote antenna to capture signal. The remote antenna shall provide a connector suitable for use with the internal cellular modem, and be of the correct impedance.
Installing the Application The Time and Attendance or Workforce Management applications can be installed on NOVUS via USB memory device. NOTE • 1 2 3 4 5 6 7 8 You can use the SVP (Suprema Versatile Platform) Android SDK to integrate the features of NOVUS to your applications. You can view the SVP Android SDK at http://kb.supremainc.com/svpsdk. Save the .apk file of the Time and Attendance or Workforce Management application to a USB memory device. Insert the USB memory device into the external USB port.
Product specifications Basic Device Category General Feature CPU Memory LCD type LCD resolution LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Camera type Camera resolution Camera angle Dimension (W x H x D) Weight Certificates Max. User (1:1) Max. User (1:N) Capacity Max. Template (1:1) Max.
Optional Parts Category Fingerprint RFID Specification • • • • • Sensor: Optical sensor (OP6) Template: SUPREMA / ISO 19794-2 / ANSI 378 R1: 125kHz(43.2 dBuV/m)EM, & 13.56MHz(44.70 dBuV/m) MIFARE, MIFARE Plus, DESFire/EV1, FeliCa, HID iCLASS SE/SR/Seos (UID Only), Legic Advant (UID Only) R2: 125kHz EM, HID Prox & 13.56MHz MIFARE, MIFARE Plus, DESFire/EV1, FeliCa, HID iCLASS SE/SR/Seos, Legic Advant (UID Only) R3: 125kHz EM & 13.
Dimensions (Unit: mm) 68 250 210 96 201.1 182.5 200.
FCC compliance information FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
EU Declaration of Conformity (CE) This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU. Hereby, Suprema Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. • NFC Frequency: 13.56 MHz • RFID Frequency: 13.56 MHz + 125 kHz For more information, contact us at the following contact information. Suprema Inc. Website: https://www.supremainc.
Appendices How to enroll a fingerprint correctly In order to improve the fingerprint authentication rate, enroll the fingerprint correctly. NOVUS can recognize a fingerprint even if the angle and position of a user's fingerprint input change. If you enroll a fingerprint with attention to the following matters, the authentication rate can be improved.
Disclaimers • The information in this manual is provided with regard to the Suprema's products. • The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS BoringSSL License BoringSSL is a fork of OpenSSL. As such, large parts of it fall under OpenSSL licensing. Files that are completely new have a Google copyright and an ISC license. This license is reproduced at the bottom of this file.
Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
ISC license used for completely new code in BoringSSL: Copyright (c) 2015, Google Inc. Permission to use, copy, modify, and/or distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies. THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of Google Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
3. Grant of Patent License.
rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.
compliance information Copyright notice The copyright of this document is vested in Suprema. The rights of other product names, trademarks and registered trademarks are vested in each individual or organization that owns such rights. Warning & Safety Information Suprema UK. 3100 Vyse Terrace, Branston Court Business Centre, Branston Street, Jewellery Quarter, Birmingham B18 6BA Tel. +44 (0) 800 368 8123 Suprema Inc.
