In this section... Superstrut Metal Framing System ® Superstrut® Metal Framing System Overview.................................................................... B-106–B-109 Channels.................................................................... B-110–B-111 Threaded Products and Hardware............................... B-112–B-117 Fittings and Brackets.................................................. B-118–B-125 Concrete Inserts.........................................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Overview New Trivalent GoldGalv Finish Is RoHS Compliant ® Thomas & Betts is proud to introduce the new and improved Trivalent GoldGalv® finish. GoldGalv® finish is a combination of .5 mils electro-plated zinc and a gold Trivalent Chromium finish.
Overview GoldGalv ® The standard GoldGalv® finish is made up of a multi-step zinc electrogalvanizing process. The Trivalent Chromium finish is applied over the zinc, producing a chemically bonded non-porous barrier for protection from moisture and air. The .5 mil electro-plated zinc and gold Trivalent Chromium finish provides all of the features and protection of Hexavalent Chromium without the use of the chemical.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Overview Outperforms the Competition Superstrut SilverGalv ® NEW! ® The Superstrut ® SilverGalv ® finish is a post-fabrication, 12-step electrogalvanizing process that applies a clear conversion coat over .5 mils of zinc. This process provides a strong, cohesive molecular bond that locks out moisture and superior corrosion resistance over standard G90 pre-galvanized channel.
Overview GoldGalv® The standard GoldGalv® finish is made up of a multi-step electrogalvanizing and zinc trivalent chromium process. The trivalent chromium finish is applied over the zinc, producing a chemically bonded non-porous barrier for protection from moisture and air. The .5 mil electro-plated zinc and gold trivalent chromium finish provides all of the features and protection of hexavalent chromium without the use of the chemical.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Channels Standard Channels Material Channels are cold formed from hot-rolled pickled and oiled strip steel. Material Thickness All Series 1200 12 gauge material All Series 1400 14 gauge material Standard Lengths Standard lengths for channel are 10 ft. and 20 ft. Standard length tolerance ± 1⁄8". Shorter lengths are available at a small cutting charge. GoldGalv® hardware finish is standard for all Superstrut products.
Channels ® Half-Slot Channel All Superstrut® Channels are available in a variety of combinations — some are shown here. Multiple channels are spot welded on 3" centers. 2" Cat. No. Dim. (In.) Ga. Std. Ctn. A-1200-HS B-1200-HS C-1200-HS E-1200-HS H-1200-HS A-1400-HS B-1400-HS 15⁄8 x 15⁄8 15⁄8 x 13⁄16 15⁄8 x 13⁄8 15⁄8 x 27⁄16 15⁄8 x 31⁄4 15⁄8 x 15⁄8 15⁄8 x 13⁄16 12 12 12 12 12 14 14 * * 500 500 * * 500 ⁄16" x 11⁄8" slots on 2" centers. 9 2-A 2* 2-B * S tandard lengths 10 ft. and 20 ft.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Threaded Products and Hardware Trapnut Strut Fastener ® NEW! The unique scissor action of the Trapnut® Strut Fastener closes at any desired position on the threaded rod. Once closed, precision threads trap the threaded rod for a sturdy hold that can be adjusted up or down for fine-tune positioning. While the versatile Trapnut has a locking pin that holds it in the desired position, it can also be removed and reused.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Threaded Products and Hardware Handle Retrofit Trapeze Applications with Ease! Easily installs above existing trapeze. Trap-Eze Connector ™ The innovative Trap-Eze™ Connector changes a time-consuming retrofit trapeze application into a streamlined process.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Threaded Products and Hardware B-114 Channel Nuts UC-100 Universal Cone Nut Superstrut® channel nuts are manufactured from mild steel and are case hardened. Design Data Superstrut® self-aligning channel nuts are designed to provide resistance to pull out and resistance to side slip in excess of the full strength of the channels with which they are used.
Threaded Products and Hardware E-145 Standard Hex Nut E-151-D Wood Screw Drive Sizes: ⁄4", ⁄8", ⁄2", ⁄8", ⁄4", 7 ⁄8" & 1" Size A: 1⁄4" 1 Sizes: 1⁄4", 5⁄16", 3⁄8", 1⁄2", 5 ⁄8", 3⁄4" & 7⁄8" 3 1 5 3 Size B: 2" GoldGalv® Finish. Nut is square over 1⁄2" size. Max. Rec. Load: 100 lbs. For all “A” and “C” series channel and inserts. AB-100 Springless Nut E-146 Standard Square Nut Sizes: ⁄4", ⁄16", ⁄8", ⁄2" & ⁄8" ES-142 Seismic Stiffener Nut GoldGalv® Finish.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Threaded Products and Hardware Regular Spring Stud Nut Fender Washer EF-147 Cat. No. size (In.) dia. (In.) ⁄4 3 ⁄8 1 ⁄2 11⁄4 11⁄2 2 EF147 1/4 EF-147-3/8 EF-147-1/2 1 hole Std. (In.) std. Ctn. ⁄16 7 ⁄16 9 ⁄16 100 100 100 5 A-182 to A-185 Cat. No. Springless Stud Nut A A-177 to A-180 Cat. No. Bolt dia. (In.) length a (In.) std. Ctn.
Threaded Products and Hardware H104 Hanger Rod, Continuous Thread — GoldGalv® H-104 Series Rod Cat. No. • Black available upon request H104 1/4X6 H104 1/4X10 H104 1/4X12 H104 3/8X6 H104 3/8X10 H104 3/8X12 H104 1/2X6 H104 1/2X10 H104 1/2X12 H104 5/8X6 H104 5/8X10 H104 5/8X12 • Machine-threaded opposite end, carbon steel • Order by Cat. No., rod size and rod length Cat. No. rod Size (In.) standard Rod Lengths std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Fittings and Brackets Fittings and Brackets — Series 200 Material Design Data Superstrut® fittings and brackets are manufactured from hot rolled carbon steel. Ratings vary when used with 12 or 14 gauge channel and are shown for each channel material. Dimensions The following standard dimensions apply to all fittings except as indicated on the individual drawings.
Fittings and Brackets 4 1⁄ 8" 5 3⁄8" 1 ⁄ 8" 7 4 1⁄ 8" 17⁄ 16" 5 3⁄8" A CAT. NO. AB-242 For use with either 3⁄8" or 1⁄2" hanger rod CAT. NO. AB252 Cat. No. A (IN.) std. Ctn. AB252 1 AB252 2 AB252 3 AB252 4 3 7⁄8 5 7⁄8 7 7⁄8 9 7⁄8 10 10 10 10 3 1⁄ 2" 3 1 ⁄ 2" CAT. NO. AB254 L CAT. NO. AB253 17⁄ 8" 17⁄ 8" 5 3⁄8" 3 1⁄ 2" 3 1⁄ 2" 2" 3 1⁄2" CAT. NO. AB254 R 2" 3 ⁄2" 1 5 3⁄8" 5 3⁄8" 3 1⁄2" CAT. NO. AB257 CAT. NO.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Fittings and Brackets Z Shape Fittings 15⁄ 8" 13 13⁄ 8" 11⁄ 16" ⁄ 16" 1 ⁄16" 1 11⁄ 16" 2 1⁄ 8" 2 1⁄ 8" 2 1⁄ 8" CAT. NO. A209 For attaching “A” series channel. CAT. NO. B209 For attaching “B” series channel. CAT. NO. C209 For attaching “C” series channel. 3 1⁄ 4" ............. Standard Dimensions.............. • • • • • 2 7⁄ 16" 17⁄ 8" Standard Finish – GoldGalv ®, unless otherwise stated.
Fittings and Brackets 5 3⁄ 8" 5 3⁄ 8" 1 21⁄ 32" 3 1 ⁄ 4" 7 1⁄ 4" 3 ⁄ 16" 5 3⁄ 8" 1 21⁄ 32" 15⁄ 8" CAT. NO. A208 Does not include strut nut or bolts. For “A” series channel. CAT. NO. A210 For attaching “A” series channel CAT. NO. A211 For attaching “A” series channel. 5 3⁄ 8" 17⁄ 8" 11⁄ 16" CAT. NO. B210 2 1⁄ 2" 7" 3 9⁄ 32" 1 5⁄ 8" 1" 121⁄ 32" 3 ⁄ 32" 11⁄ 2" 10 ga. 9 4 7⁄ 8" 1 1 5⁄ 8" CAT. NO. AB245 CAT. NO. AN211 ⁄ 4" 1 21⁄ 32" CAT. NO. AB-288 CAT. NO.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Fittings and Brackets Post Bases 15⁄8" 4 Holes 3 ⁄4" Dia. 111⁄16" 15⁄8" 1 ⁄16" 11 4 Holes 3 ⁄4" Dia. 4 1⁄2" 6" 4 1⁄2" 6" 3 1⁄4" 3 3⁄8" 3 1⁄2" 15⁄8" 15⁄8" 6" 4 1⁄2" 3 1⁄2" 15⁄8" 6" 4 Holes 3 ⁄4" Dia. 4 Holes 3 ⁄4" Dia. 41⁄2" 6" 6” 6" CAT. NO. AP-232 CAT. NO. AP-231 2 Holes 3 ⁄4" Dia. 15⁄8" 15⁄8" 1 ⁄16" 15⁄8" 15⁄8" 8" 4 Holes 3 ⁄4" Dia. 3 1⁄2" 6 1⁄2" 6 1⁄2" 8" 3 1⁄8" 3" 3 1⁄8" CAT. NO. AP-232FL CAT. NO.
4" 2 1⁄8" 4" 2 1⁄8" CAT. NO. Q202 CAT. NO. Q205 2 3⁄4" 2 3⁄4" 3 5⁄8" 3 5⁄8" 5 3⁄8" 2 7⁄16" 5 3⁄8" 6" 6" 2 7⁄16" 113⁄16" CAT. NO. Q255 For 2" standard pipe. Load 1,500 lbs. CAT. NO. Q256 For 2" standard pipe. Load 1,500 lbs. CAT. NO. Q253 For 11⁄4" standard pipe. Load 1,500 lbs. 113⁄16" Metal Framing & Cable Tray — Superstrut® Metal Framing System Fittings and Brackets Special Application Fittings CAT. NO. Q254 For 11⁄4" standard pipe. Load 1,500 lbs. 11⁄4" 3 1⁄2" 3 15⁄32" .............
Metal Framing & Cable Tray — Superstrut® Metal Framing System Fittings and Brackets Special Application Fittings (continued) 81⁄2" 6 1⁄8" 4 3⁄8" 10 1⁄2" A 4" 4" 1 5⁄8" 15⁄8" B ⁄16" 13 ⁄16" 13 AN-270 A 1" S205 Design Uniform Load/lbs. A-1,200 650 A-1,400 500 S204 Design Uniform Load/lbs. A-1,200 650 A-1,400 500 2" C 3 1⁄4" C B ⁄16" Dia. 7 ⁄32" Dia. 9 12 1⁄2" 3 1⁄8" 3 1⁄4" 3 3⁄4" 6" S-201-L and R R as shown — L opposite hand. 12 ga. steel. Design Uniform Load/lbs.
5 1⁄4" 3 1⁄8" 16 1⁄2" 13⁄16" 5 1⁄4" 3 1⁄8" 13⁄16" 18 1⁄2" 7 1⁄4" 3 1⁄8" 20 1⁄2" 7 3⁄4" 6" 1 3⁄16" 6" 6" 1 3⁄16" 1 ⁄8" 5 13⁄16" 1 5⁄8" 15⁄8" S236 Design Uniform Load/lbs. A-1,200 800 A-1,400 650 S226 Design Uniform Load/lbs. A-1,200 1,000 A-1,400 750 S222 Design Uniform Load/lbs. A-1,200 1,000 A-1,400 750 4 3⁄4" 4 3⁄4" 7 1⁄2" 5 7⁄8" S247 Design Moment (channel upright as shown) When supported by A-1,200 5,250 inch lbs. A-1,400 3,650 inch lbs. Applies to fitting only, not to the arm.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Concrete Inserts Concrete Inserts (Series 300/400) Standard lengths 10 ft. and 20 ft. length tolerance 3⁄16". Assemblies available in any length from 12" to 20 ft. Consult factory. Insert with end caps and foam filler strip installed. Material: B -302 and C-302 Insert Channel — 12 ga. steel. B-804 and C-804 End Caps — 12 ga. steel.
Concrete Inserts Cat. No. For Channel X (In.) Material Std. Ctn. C-450TB C-1,200 3 12 ga. 100 xX Does not come in pairs, order number of total pieces required. Inserts may be assembled from short pieces of channel by use of end caps. 450 Order closure strip separately. 452-TB — Spot Insert — Top is Deep Drawn Cup 3 17⁄32" • An insert with a knockout saves covering the opening.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Beam Clamps Superstrut Beam Clamps ® Materials Most products are manufactured from hot-rolled carbon steel bars or hot-rolled strip steel. Pipe rollers are cast iron. Products which are copper placed carry the letter “T” in the prefix. Design Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the “AMERICAN STANDARD CODE FOR PRESSURE PIPING.
Beam Clamps 3" 1 1⁄4" ⁄8" 7 ⁄8" 3 1 Hole ⁄16" Dia. 1 1⁄4" 3 1 5⁄8" U514A ⁄8" x 11⁄2" set screw included. Design load 1,650 lbs./per pair. U514 ⁄8" x 11⁄2" set screw included. Design load 750 lbs./per pair. 3 ⁄8" 9 3 U515 For all “A” series channel. 1 ⁄2" x 1 ⁄2" set screw included. Design load 800 lbs. 1 111⁄16" U543 Wide Flange Beam 1 3⁄4" 3 1⁄2" A-1200 Channel 2 1⁄8" 1 1⁄4" 3 1⁄2" A-597 Standard Finish — GoldGalv ® brand. Channel Series A Design load 800 lbs./ea.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Beam Clamps Beam Clamps — Malleable Iron, Silver Electroplated Finish Base Size (IN.) Cat. No. A B 500-SC 501 502 503-SC 507 508 509 510 511-SC 1 11⁄2 2 25⁄8 21⁄2 21⁄2 1 27⁄32 27⁄32 11⁄4 15⁄8 2 21⁄2 23⁄8 23⁄8 11⁄4 11⁄8 11⁄8 Jaw Tapping Set Screw Torque in Std. Opening of Base AND Load (IN.) Back Holes Rating‡ inch-lbs. Ctn.
Beam Clamps U-577 — Clevis & Swing Connector Coach Screw Standard Finish – GoldGalv ® brand Rod Size: 3⁄8" For use with wood beam. 3 ⁄8" x 13⁄4" bolt, nut and clevis included. Rod Size: 1⁄2" Standard Finish – GoldGalv ® brand For use with wood beam. U-560 — Heavy-Duty Beam Clamp “C” Set Screw Included Dimensions (in.) Cat. No. A U560 1/4 U-560-3/8 U-560-1/2 U-560-5/8 ⁄8" 7 ⁄4 ⁄8 1 ⁄2 5 ⁄8 B C Design Load lbs. Std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Beam Clamps E-231 — Structural Steel Clamp B Dimensions (In.) Cat. No. ⁄8" or 1⁄2" Rod *E-231-3/8 **E-231-1/2 A B 21⁄2 3 1 19⁄32 C Wt. lbs./C ⁄8 ⁄16 31 53 3 7 15 A Assembly requires two H-116-C ( 3⁄8") or two H-116-D ( 1⁄2") square nuts to attach hanger rod. C ⁄2" steel. 1 * Load rating of 500 lbs. with a safety factor of 3. ** Load rating of 800 lbs. with a safety factor of 3.
Beam Clamps Metal Framing & Cable Tray — Superstrut® Metal Framing System E-160 — Adjustable Beam Clamp • Clamps to I-beam where edge of beam flange does not exceed .8" thickness • Hook rod is furnished in three lengths to fit beam flanges up to 6", 9" or 12" widths Cat. No. 1 ⁄2" Hanger Rods Beam Flange Width (in.) Wt. lbs./C 21⁄2 to 6 51⁄2 to 9 81⁄2 to 12 115 125 154 ⁄2" Rod E-160-1/2-6 E-160-1/2-9 E-160-1/2-12 ⁄2 1 8, 11 or 14 1 3 Min. 3 5⁄8 Max. 2 1⁄8 ⁄16 x 11⁄2 3 Load rating 800 lbs.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Beam Clamps C-777 — Steel Top Beam Clamp & C-778 — Steel Wide JawTop Beam Clamp Cat. No. C777 3/8 C-777-1/2 C-778-3/8 C-778-1/2 rod size pipe A (In.) Size ⁄8 1 ⁄2 3 ⁄8 1 ⁄2 b c ⁄ 2–4 1 3⁄ 16 3⁄ 4 5–8 1 1⁄ 2 3⁄ 4 1 ⁄ 2–4 1 3⁄ 16 1 1⁄ 4 5–8 1 1⁄ 2 1 1⁄ 4 d e f design load lbs. 1 1 1 1 ⁄ 16 9 ⁄ 16 7 ⁄ 16 9 ⁄ 16 1 1 1⁄ 4 1 1 1⁄ 4 900 2,430 900 2,430 7 A E dimensions (in.) 1 3 B D std. Ctn.
Beam Clamps • A versatile clamp for attaching conduit to any type of beam, channel, angle or column • Designed to hold the conduit snug against the support with conduit either parallel or at right angle to it C B • The case-hardened set screw bites into the structural member for maximum security • 1⁄8" steel conduit Size ⁄8 1 D A max.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers Excellent Corrosion Resistance and a Superior Paint Base GoldGalv® hardware finish is standard for all Superstrut® products. This is a multi-process finish of electro-plated zinc, followed by gold-colorized trivalent chromium to give excellent corrosion resistance and a superior paint base. See pages B-106–B-107 for a complete description of the GoldGalv® hardware finish.
™ NEW! ® The LOC-KING™ Cobra® heavy-duty pipe and cable clamp adds two new design innovations to the heavy-duty features of the original King Cobra® clamp. Pre-set, power-tool friendly, torque mechanism for fast, efficient installation First, a pre-set torque mechanism takes the guesswork out of installation, ensuring optimum torque and eliminating excess pressure on cables.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers The new specification standard for heavy-duty industrial applications. NEW! King Cobra Cable and Pipe Clamp with GoldGalv Finish Cobra One-Piece Cable and Pipe Clamp • Superior design load capabilities for industrial applications: 350 lbs. for 1⁄2" to 2 1⁄2" trade sizes; 450 lbs.
Pipe Straps, Conduit Clamps and Hangers Metal Framing & Cable Tray — Superstrut® Metal Framing System Pre-assembled for easy handling and sorting. Superstrut Pipe Straps ® Superstrut® Pipe Straps are designed to be twist inserted anywhere along the slot side of the channel. Pipes can be placed as closely as pipe couplings permit.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers B-140 702 — Superstrut ® Straps for Rigid Conduit, IMC and Pipe 701 — Superstrut ® Straps for O.D. Tubing (continued) • For Rigid or IMC Conduit, Pipe and Electric Metal Tubing (EMT) Cat. No. Cat. No. Tubing O.D. (In.) Steel Strap Thickness Design Load (lbs.) Std.
Pipe Straps, Conduit Clamps and Hangers Angler Pipe and Conduit Clamp ® Universal Series — for EMT, IMC, Rigid and Standard Pipe Cat. NO. Rigid Series — for Rigid Conduit and Standard Pipe Strap Design Load Install Torque Size (in.) Thickness (lbs.) (in. lbs.) Std. CTN. GoldGalv ® Finish C 109 1/2 C 109 3/4 C 109 1 C 109 1 1/4 C 109 1 1/2 C 109 2 C 109 2 1/2 C 109 3 C 109 3 1/2 C 109 4 Std. CTN. GoldGalv ® Finish ⁄2 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 1 3 14 ga. 14 ga. 14 ga. 14 ga. 12 ga. 12 ga. 12 ga.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers A-716 — Snap•Guard Cushioned Clamp Tube Series ® O.D. Tubing Sizes P-716 — Pipe Series Assembly Cat. No.
Pipe Straps, Conduit Clamps and Hangers Features: Designed for use with Superstrut® channel and pipe straps and Superstrut® C-711 Hangers, and may also be used with all standard flatbar or malleable iron hangers. A A Materials: Manufactured from one-piece steel shell with reinforcing ribs for stiffening and alignment. Padding is of processed non-conducting hairfelt and is cemented to the metal. Design of ribs creates a hinge so isolator may be opened and closed to install.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers CB118 — Counter Bed Cat. No. Counter Bed CB118-047PG CB118-055PG CB118-070PG CB118-090PG CB118-110PG Std. Ctn. 100 100 100 100 100 Cat. No. Counter Bed CB118-140PG CB118-175PG CB118-200PG CB118-250PG CB118-300PG Std. Ctn. 100 100 100 100 100 CB118 Counter Bed EB118 — Extended Bed Cat. No. Extended Bed EB118-047PG EB118-055PG EB118-070PG EB118-090PG EB118-110PG Std. Ctn. 100 100 100 100 100 Cat.
Pipe Straps, Conduit Clamps and Hangers C-755 — TPE Cable Clamps An easy-to-use one-piece insulator made from Sarlink 4339D, a flameretardant, high hardness grade TPE polymer that is UL Listed. The tapered flange of the insulator ensures complete isolation and protection of the cable. Options include a Stainless Steel Clamp and hardware or an ElectroGalvanized Clamp with Everdur nut and bolt. Hole Size A C-755 Cat. No. Hole Size (in.) A (in.) Std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers HS Series Two-Hole Pipe Strap Cat. No. HS901 HS902 HS903 HS904 HS905 HS906 HS907 HS908 HS909 HS910 Pipe Size (in.) Std. Ctn. 1 ⁄2 3 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 500 500 500 250 250 125 125 100 75 50 Pipe Size (in.) Std. Ctn. ⁄8 ⁄2 3 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 500 500 500 500 250 250 50 25 25 25 25 Standard Finish — Galvanized. Carbon steel. Specify pipe size and catalog number.
Pipe Straps, Conduit Clamps and Hangers CX-725 — Extended Offset Pipe Clamp The Offset Pipe Clamp is used on pipe lines running at a fixed distance from a wall or floor. The standard clearance is two inches from the O.D. of pipe to the face of the surface. Non-standard clearances can be fabricated upon request. Designed to attach directly to piping where the exact distance between the structure and the pipe cannot be determined until the piping is in place.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers CT-720 — Copper Riser Clamp C-724 — Ductile Iron Pipe Clamp Normally used for the support of uninsulated vertical tubing where no movement will occur. Please use C-720 for carbon steel piping or C-720P for plastic coating requirements. Can be used to secure mechanical joint piping or socket fittings together to prevent separation under pressure either under or above ground, vertically or horizontally.
Designed to suspend cold or hot pipe lines where little or no insulation is required. The C-725 is usually used with an E-120-A Weldless Eyenut or E-157 Welded Eyerod. See Figure 298 heavy-duty Two-Bolt Clamp when higher loads are required. We will also design to meet special requirements such as special pipe sizes. C F E D Rated Loads are for up to 750° F (399° C). C .................................... Specifications....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-726 — Three-Bolt Pipe Clamp Designed for hot-insulated pipe lines up to 750° F. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. We will also design to meet special requirements such as special pipe sizes. C F Rated Loads are for up to 750° F (399° C). D E .................................... Specifications....................................
Pipe Straps, Conduit Clamps and Hangers Designed for hot-insulated pipelines. The spacer on the top inner bolt provides uniform space for the connecting eyerod or weldless eyenut. C F .................................... Specifications....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers CL-710 — Light-Duty Clevis Hanger CTL-710 — Copper Clevis Hanger Designed to support non-insulated, stationary lines from above, allowing for approximately 1" to 11⁄2" of vertical adjustment after the pipe is in place.
Pipe Straps, Conduit Clamps and Hangers A F B E C CL OF PIPE Cat. No. Tubing Size (IN.) Material Size ⁄2 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 5 6 16 ga x 7⁄8 16 ga x 7⁄8 16 ga x 7⁄8 16 ga x 7⁄8 16 ga x 7⁄8 13 ga x 7⁄8 1 ⁄8 x 11⁄4 1 ⁄8 x 11⁄4 1 ⁄8 x 11⁄4 1 ⁄8 x 11⁄4 3 ⁄16 x 11⁄4 3 ⁄16 x 11⁄4 ETL710 1/2 ETL-710-3/4 ETL-710-1 ETL-710-1-1/4 ETL-710-1-1/2 ETL-710-2 ETL-710-2-1/2 ETL-710-3 ETL-710-3-1/2 ETL-710-4 ETL-710-5 ETL-710-6 1 3 Dimensions (In.) A B C E F Std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-711 — J Pipe Hanger Standard Finish – GoldGalv® brand Complies with Specification MSS SP 58, Type 5. Sizes through 5" conform to Ca. Code Title 24, Div. T22 for seismic restraint bracing. C-711F — Felt-Lined J Pipe Hanger Standard Finish – GoldGalv® brand Available in sizes up to 8".
A Designed for the support of non-insulated static pipe lines. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. .................................... Specifications.................................... • Compliance: Federal Specification A-A-1192A Type 10, MSS SP-69 Type 10, UL Listed and FM Approved (3⁄4" through 8").
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-727-NFPA — NFPA Swivel Ring C-727-P — PVC-Coated Adjustable Swivel Ring Designed for the support of non-insulated static pipe lines and to protect the pipe from coming into direct contact with the hanger by having the contact surface PVC coated. The swivel nut is knurled to provide a gripping surface when adjusting the pipe elevation. Designed for the support of non-insulated static pipe lines.
Pipe Straps, Conduit Clamps and Hangers Designed for the support of non-insulated static copper tubing lines. The swivel nut is knurled to provide a gripping surface when adjusting the tubing elevation. .................................... Specifications.................................... • Compliance: Federal Specification A-A-1192A Type 10, MSS SP-69 Type 10.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers M-718, M-718-B — Extension Ring Hanger M-718 — (Rod Tapped – Electro-Galvanized) M-718-B — (Rod Tapped – Plain Finish) This split ring hanger is designed for the support of non-insulated stationary pipe lines. Also available in a two-screw design. The MT-742-R Ceiling Plate is normally used with this product. A .................................... Specifications....................................
Pipe Straps, Conduit Clamps and Hangers (Consult Superstrut® Seismic Hanger bulletin for additional information.) 15⁄8" 15⁄8" 15⁄8" 2 ⁄8" 3 2 3⁄8" 13⁄4" ⁄16" Dia. 11 2 Holes ⁄16" Dia. ⁄16" 9 15 41⁄2" 4 1⁄2" 41⁄2" ⁄4" ⁄4" ⁄4" 1 1 1 15⁄8" 2 Holes ⁄16" Dia. 15⁄8" CAT. NO. C749N Seismic Brace 1,500 lb. load safety factor of 3 15⁄8" 9 2 Holes ⁄16" Dia. 9 CAT. NO. C749N 7/8 Seismic Brace 1,650 lb. load safety factor of 3 CAT. NO. C749N 5/8 Seismic Brace 1,650 lb.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers PG-794 — Pipe Alignment Guide Designed to maintain the axial alignment of piping as it expands and contracts during operation. It is most typically installed adjacent to expansion joints and at reasonable distances between the expansion joint and the anchor point. Our Figures 1007 and 1010 also offer alternative means for your piping alignment needs.
M-742-R Ceiling Flange A M-742-R, M-742-RB, MT-742-R – Single Plate M-742-R — (Rod Tapped – Electro-Galvanized) M-742-RB — (Rod Tapped – Plain Finish) MT-742-R — (Rod Tapped – Copper Finish) B Designed for attaching a rod to a wooden member. This part is normally used in conjunction with our M-718 Split Ring. Tap .................................... Specifications.................................... • Material: Malleable Iron. M-742-R is Carbon Steel.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-736 — Light Welded Steel Bracket Designed to support up to 6" pipe. This bracket is for installation to walls as shown or inverted, and may require a backing plate. Holes for up to 3⁄4" rods are located at each end of the bracket to allow for use in either orientation. The C-736 S ide Clip Steel Bracket Clip can be attached to the C-736 to support piping 31⁄2" or smaller.
Pipe Straps, Conduit Clamps and Hangers Metal Framing & Cable Tray — Superstrut® Metal Framing System PG-795 — Pipe Block 3" Standard Finish — Black (B). ⁄8" 7 11⁄2" 7 ⁄16" Dia. Pipe Attachments H-115, H-115SS — Standard U-Bolt Our standard U-Bolts are recommended for use as supports or guides for piping. They are supplied with four hex nuts. The H-115SS is recommended for support of stainless steel piping. Please specify the grade of stainless steel you require when ordering.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers Beam Attachments M-750 — Side Beam Bracket G Designed for bolt connections. ....................................Specifications..................................... • Compliance: A-A-1192A Type 34 and MSS-SP 69 Type 34 • Material: Malleable Iron (Maximum Temperature 450° F/232° C) max load (lbs.) Cat. No. M-750-3/8 M-750-1/2 M-750-5/8 rod size (in.
Pipe Straps, Conduit Clamps and Hangers F-112 — Turnbuckle M-129 — Extension Piece Used to connect right- and left-hand threaded rods together and provide for adjustment. Designed for attaching rods to the M-732-EXT Clamp and similar types of attachments. ....................................Specifications..................................... ....................................Specifications.....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System B-166 Pipe Straps, Conduit Clamps and Hangers Structure Attachments C-780 W/OB, C-780 W/HWB — Welded Beam Attachment Recommended for attachment to the bottom of beams when little or no pipe movement is expected. C-780 W/HWB is recommended for attachment to the bottom of beams, when pipe movement is expected. A bolt and nut or pin is supplied. A pin with cotters is normally supplied for rod sizes over 1". S E C Rod Size A ....................
Pipe Straps, Conduit Clamps and Hangers A Designed to attach to the bottom of flanged beams. Normally used with the E-157 Eye Rod or E-120-A Eye Nut. B D .................................... Specifications....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers M-732-H — Steel Beam Clamp with Weldless Eyenut The M-732-H beam clamp with eyenut is used for support where some movement is expected and welding to the structure is prohibited. The clamping effect is produced by the “ice-tong” action of the arms and is locked in place by the through bolt located just under the beam flange. E .................................... Specifications...........................
Designed to attach to the bottom of flanged beams without requiring welding. Normally used with the M-129 Extension Piece (not furnished) up to a maximum 7⁄8" (M20) rod diameter. Loading is achieved through the clamp jaws while locking is accomplished by tightening the through-bolt located directly below the flange. Maximum flange thickness is .60 inches. A .................................... Specifications....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-728 — Pipe Roller (Pair) C728H — Pipe Roller Assembly (Pair) • Cast aluminum rollers, steel brackets Cast aluminum roller, steel brackets. Order separately for each pair of rollers: • Designed for standard saddles Two 1⁄2" x 5⁄16" hex head cap screws Two 1⁄2" channel nuts • Order separately for each pair of rollers: Two 1⁄2" x 5⁄16" hex head cap screws, two 1⁄2" channel nuts Adjustable to fit O.
Pipe Straps, Conduit Clamps and Hangers A Designed to support piping lines from above, allowing for vertical adjustment and axial movement in the piping. The lower nut (not furnished) adjusts the pipe line to the proper elevation. The top nut (not furnished) prevents loosening due to vibration and must be tightened securely to assure proper hanger performance. E B .................................... Specifications.................................... • Material: Carbon Steel frame with a Cast Iron Roll.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers CR-729A — Roller Chair Designed for longitudinal movement of pipe where vertical adjustment is not required. Although two bolts are supplied for installation, the chair can be alternatively welded in position. Cat. No. Pipe Size (in.) Max. Load (lbs.
Pipe Straps, Conduit Clamps and Hangers Designed for longitudinal movement of pipe where vertical adjustment is required. Although primarily used for support of the pipe, this component may also be placed over the pipe to act as a guide. B .................................... Specifications.................................... • Material: Cast Iron Pipe Roll and Sockets with a Carbon Steel Axle. Do not exceed 450° F/232° C at the contact point to the roll. • Compliance: A-A-1192A Type 42, MSS SP-69 Type 41.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers S-730-C — Chair and Roll Designed for longitudinal movement of pipe where vertical adjustment is not required. Because the chair is made of steel, it can be either welded or bolted in position. Chair No. O S C K O E E N N Chair No. 1A & 1 C-789A C-789B S-730-C C-789C Chair No. 2 thru 6 C-789D C-789E Bare Pipe Size 1" Cov. 25 11⁄2" Cov. 38 2" Cov. 51 21⁄2" Cov. 64 3" Cov. 76 4" Cov.
Used for support of piping from below without welding to the pipe, and consists of a steel saddle, nipple and pipe reducer. It connects to a threaded pipe standard and base. CL Rated loads are for up to 650° F (343° C). .................................... Specifications.................................... • Materials: Reducer is Cast Iron, Pipe saddle and nipple are carbon steel. • Compliance: Federal Specification A-A-1192A Type 39, MSS-SP-69 Type 39.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers C-789, C-789A, C789B, .................................... Specifications.................................... • Material: Carbon Steel (except • Finish: Standard Finish – GoldGalv , C-789C, C-789D, C-789 and C-789-8 which are Black (add suffix “-B”), ElectroChromium Molybdenum Steel). Galvanized (add suffix “-EG”).
Pipe Straps, Conduit Clamps and Hangers Cat. No.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers Covering Thickness 12" Center Rib Sizes 12" & Larger B B A Figure 1 A Figure 2 C-789 Pipe Saddles and Pipe Shields (Continued) figure 1 (in.) Cat. No.
Pipe Straps, Conduit Clamps and Hangers Designed to protect the insulation and distribute the load at the hanger point. This item is usually used with our C-710 Clevis Hanger. ....................................Specifications.....................................
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers Rods and Rod Attachments Shield Size Selection Table Cat. No.
Pipe Straps, Conduit Clamps and Hangers Welded Eyerods are designed to permit swing in the attachment component due to pipe movement. B .................................... Specifications.................................... • Material: Carbon Steel. Larger rod diameters over 21/2", special materials and special eye dimensions can be furnished upon request • Finish: Standard Finish – GoldGalv®, Black (add suffix “-B”), ElectroGalvanized (add suffix “-EG”) A (IN.) B (IN.) Thread Length D (IN.) Load at (LBS.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Pipe Straps, Conduit Clamps and Hangers F-111 — Forged Steel Clevis Used to connect rod ends with structural steel welding lug plates or lugs welded to pipe. It provides a pivot point and adjustment. It can be supplied with a pin as F-111. Tap .................................... Specifications....................................
Surface Raceway and Lighting Systems Series 800 Surface Raceway and Lighting Systems Superstrut® channel together with snap-in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories listed by Underwriters Laboratories are identified on the drawings. Electrical Applications Column A Suitable for number of wires indicated when used as a raceway.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Surface Raceway and Lighting Systems Electrical Applications (continued) AB-888 Page B-187 822 Page B-186 H104 Page B-117 805 Page B-186 AB-844 Page B-187 A-854 Page B-186 A-853 Page B-186 AB-803 Page B-187 A-853 Page B-186 AB-885 Page B-187 811 Page B-186 804 Page B-186 Standard Finish – GoldGalv ® brand B-184 United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.1354 AB-866 Page B-187 Technical Services Tel: 888.862.
Surface Raceway and Lighting Systems Metal Framing & Cable Tray — Superstrut® Metal Framing System A-891 Page B-186 AB-888 Page B-187 A-892 Page B-186 A-853 Page B-186 A-854 Page B-186 AB-844 Page B-187 Standard Finish – GoldGalv brand ® A-854 Page B-186 AB-288 Page B-121 E-145 Page B-115 802 Page B-186 ES-145 Page B-115 A-1200-P Page B-111 Order nuts separately 452TB Concrete Spot Insert Page B-127 540 Side Beam Hanger Clip Page B-130 www.tnb.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Surface Raceway and Lighting Systems 13⁄8" Fixture Fittings ⁄32" 3 * ⁄4"–16 UNF Thread 3 1 ⁄32" 21 A-243-1 End Cap for A-1200 Channel 41⁄2" ⁄8" 7 A-213 21⁄16" 809 Tapped End Cap 802 Raceway Joiner with Reinforcing Plate furnished complete with nuts. Cat. No. A802 B-802 E-802 H-802 For Channel std. Ctn. A Series B Series E Series H Series 25 25 10 10 12 ga for 3⁄4" or 1" Conduit.
Surface Raceway and Lighting Systems Listed 15⁄8" 4" 4 ⁄4" 3 AB803* Cast Conduit Connector To connect 1⁄2" or 3⁄4" conduit to raceway channel — Furnished complete with stud nuts & hex nuts. Part has removable bushing to increase size from 1⁄2" to 3⁄4". AB815 Swing Connector Nuts & bolts to clamp to channel included. For 1⁄2" or 3⁄4" conduit.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Slotted Angle Metal Framing With Superangle, You Get Flexibility — Simplicity — Economy! Superangle Slotted Angle Metal Framing Create the support framing you need. Superangle is manufactured from structural-quality steel in three different sizes. The small sizes are 14 ga. steel, the larger size is 12 ga. steel.
Slotted Angle Metal Framing Cat. No. Length (Ft.) FT. Per PKG. Std. Ctn. 10 12 10 12 10 12 50 60 50 60 50 60 1,000 1,200 1,000 1,200 1,000 1,200 RA-160-10 RA-160-12 RA-225-10 RA-225-12 RA 300 10 RA-300-12 5 Lengths, 36 Nuts and Bolts RA-300 12 Gauge 31⁄8" x 15⁄8" RA-225 14 Gauge 2 3⁄8" x 15⁄8" RA-160 14 Gauge 15⁄8" x 15⁄8" Superangle Accessories Casters Cat. No. RA RC RA SC RA-RC Rigid Center RA-SC Swivel Caster STD. PKG. Std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes Properties for Design — Stainless Steel (Suffix SS/Type 304 and 6SS/Type 316) Superstrut® stainless steel products are made from high-quality austenitic Type 304 and Type 316 material. Stainless steel contains large amounts of chromium and nickel, is non magnetic and offers superior corrosion resistance.
15⁄8" 15⁄8" 7 ⁄8" 12 ga. 31⁄4" 15⁄8" A Series A-1200_AL 15⁄8" deep channel and combination A-1202_AL A-1202-C_AL ⁄8" 7 A-1200-HS_AL Slots 2" on center. Slot size 9⁄16" x 11⁄8" 15⁄8" 15⁄8" 7 ⁄8" ⁄16" 13 15⁄8" 12 ga. Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes Aluminum Products (AL Suffix) B Series B-1200_AL B-1202_AL 47⁄8" 21⁄2" 15⁄8" 17⁄8" X201_AL 21⁄4" AB201_AL 702_AL Rigid Conduit Pipe Strap www.tnb.com United States Tel: 901.252.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes Stainless Steel Products Available in: • Type 304 Stainless Steel — SS Suffix • Type 316 Stainless Steel — SS6 Suffix 15⁄8" 7 ⁄8" 15⁄8" ⁄8" 7 A Series A-1200_SS A-1200_T316SS A-1200-HS_SS A-1200_HS_T316SS A-1202_SS A-1202-T316SS 15⁄8" 7 ⁄8" ⁄16" 13 B Series A-1202-HS_SS A-1202-HS_T316SS A-100 Regular Spring Nut ⁄8" 7 12 gauge B-1200_SS B-1200_T316SS 14 gauge B-1400_SS B-1400_T316SS B-100 Short Spring Nu
Available in: • Type 304 Stainless Steel — SS Suffix U501, U502 • Type 316 Stainless Steel — SS6 Suffix H-119 Rod Coupling Cat. No. For Channel U501 A-1200 A-1400 B-1200 B-1400 C-1200 B-1402 A-1202 A-1402 C-1202 H-1200 U502 A A (in.) Std. Ctn. 33⁄16 20 413⁄16 20 Furnished complete Design Load U 501 — 2150 lbs. U502 — 3000 lbs. C-775L — Clamp with Lock Nut A Cat. No. AB201 D B Dimensons (in.) Rod Size (In.) A B C D Design Load (lbs.) Std. Ctn.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes Type 304 Stainless Steel Products (SS Suffix) 4 7⁄8" 1 5⁄8" 2 1⁄2" 2" 17⁄8" 6H Series 6H-B Series Conduit and Pipe Hanger X201 AB202 3 5⁄8" 3 5⁄8" 2 1⁄4" 4 1⁄8" AB206 AB204 AB203 5 3⁄8" 7 1⁄4" 4 1⁄8" 31⁄2" AB207 X207 AB213 3 1⁄2" 9 5⁄32" 3 3⁄4" 41⁄8" 3 1⁄2" 3 7⁄8" 3 1⁄2" 15⁄8" 121⁄32" AB214 B-194 AW219 AB219 United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.
Special Metals and Finishes 5 5⁄8" 45° 3 1⁄2" 45° 3" 3 1⁄2" 11⁄16" 2 5⁄16" 2 1⁄2" AB220 AB225 SPAB-227 3 1⁄4" 4 Holes 3 ⁄4" Dia. 111⁄16" ⁄4" Dia. 3 3 1⁄2" 1 ⁄8" 5 3 1⁄2" 111⁄16" 3 1⁄2" ⁄4" Dia. 3 6" 6" 6" 41⁄4" 41⁄4" 6" AP-232SQ AP-232 4 Holes 3 ⁄4"Dia.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes White Painted Products (WH Suffix) 15⁄8" 7 ⁄8" 15⁄8" 7 ⁄8" 1 ⁄8" 5 ⁄16" 13 A Series B Series ⁄8" 7 A-1200 A-1200-HS B-1400 B-1400-HS A-1202 A-1202-HS ⁄8" 7 15⁄8" 4 7⁄8" 1 7⁄8" 2 1⁄2" 2 1⁄4" 2 1⁄2" 2" 17⁄8" AB201 X201 AB219 41⁄8" 17⁄8" 41⁄8" AB203 B-196 2" AW204 United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.1354 Technical Services Tel: 888.862.3289 3 1⁄2" AB205 www.tnb.
Special Metals and Finishes Metal Framing & Cable Tray — Superstrut® Metal Framing System White Painted Products (WH Suffix) (continued) 3 7⁄8" 1" 17⁄8" 13⁄4" 17⁄8" 13⁄4" 3 3⁄4" N-205 AW-205-R AW205 L 11⁄16" 5 3⁄8" 3 1⁄2" 7 1⁄4" AB-206 AB-207 5 3⁄8" 5 7⁄16" X-207 3 1⁄2" 3 1⁄2" 3 7⁄8" 15⁄8" 15⁄8" 121⁄32" A218 A210 For attaching A Series channel AB-219 5 3⁄8" 45° 3" 31⁄2" 2 5⁄16" 3 ⁄2" 1 11⁄16" 5 3⁄8" AB-220 N-219 www.tnb.com United States Tel: 901.252.8000 800.816.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Special Metals and Finishes White Painted Products (WH Suffix) (continued) AB-241 Cat. No. AB-241-1/4 AB-241-3/8 AB-241-1/2 rod Size (In.) std. Ctn. ⁄4 ⁄8 1 ⁄2 100 100 100 1 3 111⁄16" 4 Holes 3 ⁄4" Dia. 15⁄8" 5 ⁄8" 3 4 Holes 3 ⁄4" Dia. 3 1⁄2" 5 ⁄8" 3 3 1⁄2" 111⁄16" 6" 6" 41⁄4" 41⁄4" AP-232 AB253 4 Holes 3 ⁄4" Dia. 3 1⁄4" 4 Holes 3 ⁄4" Dia.
W Y Elements of Sections W Y Nominal Thickness (IN.) X X Z X X I — Moment of Inertia S — Section of Modulus r — Radius of Gyration Z — Nominal Axis A — Area 12 ga. = .105 14 ga. = .075 16 ga. = .060 H Z H Y Y Single Channels Double Channels Table 1 — Properties for Design: Single Channel H in. W in. A in.2 I in.4 S in.3 r in. X-X AXIS Z in. I in.4 S in.3 Y-Y AXIS r in. 1.625 .813 1.375 2.438 3.250 1.625 .813 1.625 1.625 1.625 1.625 1.625 1.625 1.625 .557 .381 .500 .726 .897 .401 .
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Design Loads for Channel Used as Beam or Column. Table 3 Beam Loads Table 3 contains simple beam, uniformly-distributed loads calculated at 25,000 psi fiber stress. Beam loads are based on channel being loaded across the x-x axis. Loads are also listed at reduced deflections for long spans.
Technical Information Cat. No. Maximum Uniform Depth (in.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Table 3 — Double Channel (Single Channels Welded Back-to-Back) Cat. No.
Technical Information Cat. No. A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 42" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 48" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 54" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 Maximum Uniform 1/180 Span 1/360 Span depth (in.) Ga. Load Defl. Load Defl. Load Defl. col. Load 15⁄8 ⁄16 13⁄8 27⁄16 31⁄4 15⁄8 13 ⁄16 12 12 12 12 12 14 14 1,178 350 861 2,216 3,528 811 284 .129 .236 .149 .088 .
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Table 3 — Double Channel (Single Channels Welded Back-to-Back) Cat. No.
Technical Information Cat. No. 60" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 66" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 72" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 84" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 Maximum Uniform 1/180 Span 1/360 Span depth (in.) Ga. Load Defl. Load Defl. Load Defl. col. Load 15⁄8 ⁄16 13⁄8 27⁄16 31⁄4 15⁄8 13 ⁄16 12 12 12 12 12 14 14 706 210 516 1,330 2,116 486 170 .
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Table 3 — Double Channel (Single Channels Welded Back-to-Back) Cat. No.
Technical Information Cat. No. 96" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 108" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 120" Beam or Column A-1200 B-1200 C-1200 E-1200 H-1200 A-1400 B-1400 144" Beam or Column A-1200 C-1200 E-1200 H-1200 A-1400 Maximum Uniform 1/180 Span 1/360 Span depth (in.) Ga. Load Defl. Load Defl. Load Defl. col. Load 15⁄8 ⁄16 13⁄8 27⁄16 31⁄4 15⁄8 13 ⁄16 12 12 12 12 12 14 14 441 — 323 831 1,323 304 — .914 — 1.059 .730 .
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Table 3 — Double Channel (Single Channels Welded Back-to-Back) Cat. No.
Technical Information Cat. No. 168" Beam or Column A-1200 C-1200 E-1200 H-1200 A-1400 192" Beam or Column E-1200 H-1200 216" Beam or Column E-1200 H-1200 240" Beam or Column E-1200 H-1200 Maximum Uniform 1/180 Span 1/360 Span depth (in.) Ga. Load Defl. Load Defl. Load Defl. col. Load 15⁄8 13⁄8 27⁄16 31⁄4 15⁄8 12 12 12 12 14 — — 475 756 — — — 1.912 1.463 — 84 53 233 482 60 .933 .933 .933 .933 .933 42 27 116 241 30 .467 .467 .467 .467 .467 — — — — — 27⁄16 31⁄4 12 12 — 661 — 1.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Data — Metal Framing Channel (continued) Table 3 — Double Channel (Single Channels Welded Back-to-Back) Cat. No. 168" Beam or Column A-1202 B-1202 C-1202 E-1202 H-1202 A-1402 B-1402 192" Beam or Column A-1202 — C-1202 E-1202 H-1202 A-1402 — 216" Beam or Column A-1202 — C-1202 E-1202 H-1202 A-1402 — 240" Beam or Column A-1202 — C-1202 E-1202 H-1202 A-1402 — Maximum Uniform 1/180 Span 1/360 Span depth (in.) Ga.
Technical Information Section Recommended Load in lbs. Section Recommended Load in lbs. Section Recommended Load in lbs.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Applications Cantilever Beams Simple Beams Beams Fixed on One End, Supported at Other Beams Fixed at Both Ends B-212 United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.1354 Technical Services Tel: 888.862.3289 www.tnb.
Technical Information Table 6 — Conversion Factors for Beams with Various Static Loading Conditions LOAD AND SUPPORT CONDITION LOAD FACTOR DEFLECTION FACTOR 1. Simple Beam — Uniform Load 1.00 1.00 2. Simple Beam — Concentrated Load at Center .50 1.25 3. Simple Beam — Two Equal Concentrated Loads at 1⁄4 Points 1.00 1.10 4. Beam Fixed at Both Ends — Uniform Load 1.50 .30 5. Beam Fixed at Both Ends — Concentrated Load at Center 1.00 .40 6. Cantilever Beam — Uniform Load .25 2.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Applications (continued) Example I Problem: 5"–0" 5"–0" Determine the load and deflection of an A-1200 beam continuous over one support and loaded uniformly on one span. Solution: A. From load table 3 for A-1200 the load for a 5'0" span is 706 lbs. and deflection is .358". B. Multiply by factors from Table 6. Load = 706 lbs. x 1.30 = 917.8 lbs. Deflection = .358 x .92 = .
Technical Information DIMENSIONS (in.) — LOADS DIMENSIONS (in.) — LOADS nominal Rod Dia. root area Thread nominal Rod Dia. ⁄8 1 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 .068 .126 .202 .302 .419 ⁄4 to 2 21⁄2 to 31⁄2 4 to 5 6 8 to 12 1 root area Thread ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 3 1 1 Safety factor of 5. Safety factor of 5. Table 9 — Maximum Spacing between Pipe Supports Steel Pipe Nom. Pipe Size (IN.) Max. Spacing (FT.) Copper Size Nom. Pipe Size (IN.) Max. Spacing (FT.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Applications (continued) Table 11 — Standard Dimensions and Weights of Piping Materials and Conduit Mechanical (Schedule 40) Nominal Std. Pipe Size (in.) Pipe O.D. (in.) Coupling O.D. (in.) ⁄2 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 5 6 8 10 12 14 16 18 20 22 24 26 28 30 .84 1.05 1.32 1.66 1.90 2.38 2.88 3.50 4.00 4.50 5.56 6.63 8.63 10.75 12.75 14.00 16.00 18.00 20.00 22.00 24.00 26.00 28.00 30.00 1.06 1.31 1.58 1.90 2.
Technical Information A.S.A. B36.10 SCHEDULE NOS. AND NOMINAL WALL THICKNESS DESIGNATIONS Nominal Pipe Size (in.) Outside Diameter (in.) Wall Thickness (in.) Inside Diameter (in.) ⁄8 ⁄2 3 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 5 6 8 10 12 14 OD 16 OD 18 OD 20 OD 24 OD 10 12 14 OD 16 OD 18 OD 20 OD 24 OD .675 .840 1.050 1.315 1.660 1.900 2.375 2.875 3.500 4.000 4.500 5.563 6.625 8.625 10.750 12.750 14.000 16.000 18.000 20.000 24.000 10.750 12.750 14.000 16.000 18.000 20.000 24.000 .126 .147 .154 .179 .191 .
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Design Applications (continued) • General Storage Racks • Pallet Racks • Barrel Racks • Bulk Furniture Racks Column height, equal shelf spacing • Cable Racks • Bar Stock Racks • Display Racks • Special Purpose Racks • F or Uniform Loads on Horizontal Members, See Table 3 (pages B-200–B-210) Typical general storage rack for use with plywood or other decking Table 14 — Column Loading for Rack Construction colum Height 6
Technical Information C-710 Adj. Steel Clevis 3 Sizes ⁄4" through 20" IPS Federal Type 1 SP69 Type 1 C-726 Steel Double Bolt Pipe Clamp 1 Sizes 1 ⁄2" through 24" IPS Federal Type 3 SP69 Type 3 C-725 Steel Pipe Clamp 1 Sizes 1 ⁄2" through 24" IPS Federal Type 4 SP69 Type 4 CF-710 Adj. Steel Band Hanger 1 Sizes ⁄2" through 8" IPS 3⁄4" through 4" tube Federal Type 7 C-720/CT-720 Extension Pipe or Riser Clamp Sizes 3⁄4" through 20" IPS 1⁄2" through 6" tube Federal Type 8 SP69 Type 8 C-727/CT-727 Adj.
Metal Framing & Cable Tray — Superstrut® Metal Framing System Technical Information Federal Specifications (WW-H-171)/ Manufacturers Society Specifications (MSS SP69) (continued) C-704-A Offset J-Hook 1 Sizes ⁄2" through 3" IPS Federal Type 27 M-732-H I-Beam w/Eye Nut Federal w/o links Type 28 Federal w/links Type 29 SP69 Type 28 M-732/M-732 Ext I-Beam Clamp w/Swing Nut Sizes 3⁄8" through 7⁄8" Rod Federal Type 30 SP69 Type 30 C-736 Light Welded Steel Bracket Federal Type 32 SP69 Type 31 C-739-H Heavy
