Datasheet

2-26
X7DB8/X7DBE User's Manual
GLAN1
®
JLAN1
S
U
PER X7DB8/E
GLAN2
Fan
1
8-pin PWR
FP Ctrl
SPK
PW LED
JOH1
Fan3
IDE1
Floppy
BIO
S
320 SCSI Channel A
Fan4
SATA1
SATA0
USB2
/3
S
MB
P
CI-
X
100 MHz ZCR
P
C
I-
X
133 M
Hz
J
WD
Batter
y
V
G
A
PC
I-Exp
x
8
Nort
h
B
rid
g
e
V
G
A
COM1
USB0
/1
KB/
M
ouse
Fan
6
Fan
5
AT
X
PWR
4-Pin
PWR
J3P
Parrallel Port
24-Pin
J
P
G
1
SCSI CTRL
C
PU
1
C
PU
2
S
outh
B
rid
g
e
P
X
H
DIMM 1A (Bank
1
)
Fan
7
JAR
PSF
Fan2
C
ompact
Flash
L
E1
Fan8
J
CF1
JW
F
1
JPA
2
JPA3
JPA1
320 SCSI Channel B
SATA3
SATA2
SATA4
SATA5
JL1
J
K1
S
lot1
S
lot2
S
lot3
P
CI-
X
133 M
Hz
S
lot4
J
P
L1
J
P
L2
S
lot5
PCI-Exp x4
S
lot6
PCI-Exp x8
SEPC
SIMLP IPMI
S
lot7
DIMM 1
B
(Bank
1)
D
IMM 2
A (B
ank
2
)
DIMM 2B (Bank
2)
D
IMM 3
A (B
ank
3
)
DIMM 3B (Bank
3)
DIMM 4A (Bank 4
)
D
IMM
4
B (B
an
k
4
)
J
B
T1
US
B
4
J
WOR
J
COM
2
DA2
WOL
DA
1
S
I/O
JP1
L
A
N
CTR
L
J27
J28
S
G
P
IO1
S
G
P
IO
2
SMB PS
CTR
L
J7
A
A. SCSI Enable
B. SCSI Channel A Termi-
nation Enable
C. SCSI Channel B Termi-
nation Enable
SCSI Controller Enable/
Disable
Jumper JPA1 is used to enable or disable
the LSI SCSI controller. The default set-
ting is on pins 1-2 to enable SCSI. See
the table on the right for jumper settings.
SCSI Termination Enable/
Disable
Jumpers JPA2/JPA3 are used to enable
or disable termination for SCSI Channel
A (JPA2) and Channel B (JPA3) connec-
tors. The default setting is open to enable
termination. See the table on the right for
jumper settings.
Note: In order for the SCSI drives to
function properly, please do not change
the default setting (enabled) set by the
manufacturer.
SCSI Term. Enable/Disable
Jumper Settings
Jumper Setting Defi nition
Open Enabled
Closed Disabled
B
C
VGA Enable/Disable
Jumper Settings (JPA1)
Jumper Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled