Datasheet

Chapter 2: Installation
2-33
LAN1/2
®
JLAN1
S
UPER X7DA3
Fan1
8-pin PWR
FP Control
SPK
PW LED
JOH1
Fan3
IDE1
Floppy
Fan4
SATA3
SATA5
USB4/5
SMB
PCI-X 100 MHz ZCR (Gre
en Slot)
PCI-X 133 MHz
JWD
Battery
GLAN
CTLR
PCI-Exp x4
North Bridge
COM1
Fan6
Fan5
ATX PWR
4-Pin
PWR
J3P
Parrallel Port
24-Pin
SAS
Controller
PXH
CPU1
CPU2
South
Bridge
Fan7
JAR
J17
PSF
JPW3
Fan2
Compact Flash
LE1
Fan8
JCF1
JWF1
SATA2
SATA4
SATA1
SATA0
JL1
Slot1
Slot2
Slot3
PCI-X 133 MHz
Slot4
JPL2
Slot5
PCI-33MHz
Slot6
PCI-Exp x16
SIM LP IPMI
Slot7
J7B1
J7B2
J7B3
J8B1
J8B2
J8B3
J9B1
J9B2
DIMM 1A (Bank 1)
DIMM 1B (Bank 1)
DIMM 2A (Bank 2)
DIMM 2B (Bank 2)
DIMM 3A (Bank 3)
DIMM 3B (Bank 3)
DIMM 4A (Bank 4)
DIMM 4B (Bank 4)
JBT1
JWOL
JWOR
COM2
KB/
Mouse
USB 0/
1/2/3
JPAC
JI
2
C2
JI
2
C3
JI
2
C4
Greencreek
BIOS
CPU
Fan 1
CD2 CD1
JPL1
JI
2
C1
CPU Fan2
Line-In/
Line-
Out
Mic
SGPIO1
SGPIO2
JS10
SAS4-7
SAS0-3
JPS1
ACT0-3
PRES0-3
PRES4-7
ACT4-7
IDE Drive Connectors
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
1 Reset IDE 2 Ground
3 Host Data 7 4 Host Data 8
5 Host Data 6 6 Host Data 9
7 Host Data 5 8 Host Data 10
9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 Key
21 DRQ3 22 Ground
23 I/O Write 24 Ground
25 I/O Read 26 Ground
27 IOCHRDY 28 BALE
29 DACK3 30 Ground
31 IRQ14 32 IOCS16
33 Addr1 34 Ground
35 Addr0 36 Addr2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground
A
B
A. IDE#1
B. IDE#2 (Compact Flash)
IDE Connectors
There are two IDE Connectors (JIDE1:
Blue, JIDE2: White) on the mother-
board. The blue IDE connector (JIDE1)
is designated as the Primary IDE Drive.
The white IDE connector (JIDE2) is des-
ignated as the Secondary IDE Drive,
reserved for Compact Flash Card use
only. (See the note below.) See the
table on the right for pin defi nitions.
*Note: JIDE2 (the white slot) is re-
served for Compact Flash Card use
only. Do not use it for other devices.
If JIDE2 is populated with a Compact
Flash Card, JIDE1 (the blue slot) will
be available for one device only. For the
Compact Flash Card to work properly,
you will need to connect a power cable
to JWF1 fi rst.