Datasheet

Chapter 2: Installation
2-31
LAN1/2
®
JLAN1
S
UPER X7DA3
Fan1
8-pin PWR
FP Control
SPK
PW LED
JOH1
Fan3
IDE1
Floppy
Fan4
SATA3
SATA5
USB4/5
SMB
PCI-X 100 MHz ZCR (Gre
en Slot)
PCI-X 133 MHz
JWD
Battery
GLAN
CTLR
PCI-Exp x4
North Bridge
COM1
Fan6
Fan5
ATX PWR
4-Pin
PWR
J3P
Parrallel Port
24-Pin
SAS
Controller
PXH
CPU1
CPU2
South
Bridge
Fan7
JAR
J17
PSF
JPW3
Fan2
Compact Flash
LE1
Fan8
JCF1
JWF1
SATA2
SATA4
SATA1
SATA0
JL1
Slot1
Slot2
Slot3
PCI-X 133 MHz
Slot4
JPL2
Slot5
PCI-33MHz
Slot6
PCI-Exp x16
SIM LP IPMI
Slot7
J7B1
J7B2
J7B3
J8B1
J8B2
J8B3
J9B1
J9B2
DIMM 1A (Bank 1)
DIMM 1B (Bank 1)
DIMM 2A (Bank 2)
DIMM 2B (Bank 2)
DIMM 3A (Bank 3)
DIMM 3B (Bank 3)
DIMM 4A (Bank 4)
DIMM 4B (Bank 4)
JBT1
JWOL
JWOR
COM2
KB/
Mouse
USB 0/
1/2/3
JPAC
JI
2
C2
JI
2
C3
JI
2
C4
Greencreek
BIOS
CPU
Fan 1
CD2 CD1
JPL1
JI
2
C1
CPU Fan2
Line-In/
Line-
Out
Mic
SGPIO1
SGPIO2
JS10
SAS4-7
SAS0
-3
JPS1
ACT0-3
PRES0-3
PRES4-7
ACT4-7
Parallel (Printer) Port
Connector
The parallel (printer) port is located
at J21. See the table on the right for
pin defi nitions.
2-9 Parallel Port, Floppy Drive, Hard Disk Drive and
SIMLP IPMI Connections
Note the following when connecting the fl oppy and hard disk drive cables:
• The fl oppy disk drive cable has seven twisted wires.
• A red mark on a wire typically designates the location of pin 1.
• A single fl oppy disk drive ribbon cable has two connectors to provide for two
fl oppy disk drives. The connector with twisted wires always connects to drive
A, and the connector that does not have twisted wires always connects to drive
B.
Parallel (Printer) Port Connector
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
1 Strobe- 2 Auto Feed-
3 Data Bit 0 4 Error-
5 Data Bit 1 6 Init-
7 Data Bit 2 8 SLCT IN-
9 Data Bit 3 10 GND
11 Data Bit 4 12 GND
13 Data Bit 5 14 GND
15 Data Bit 6 16 GND
17 Data Bit 7 18 GND
19 ACK 20 GND
21 BUSY 22 Write Data
23 PE 24 Write Gate
25 SLCT 26 NC
A
A. Parallel Port