Quick reference (1.0)
S
UPERMICR
R
ContaCt InformatIon
• www.supermicro.com(Email:support@supermicro.com)
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
PaCkage Contents
(Appliestoindividual-packonly)
X10DRL-CT / -iT / -C
QuICk referenCe guIde
• One(1)SupermicroMotherboard
• X10DRL-CT/-C:Two(2)SATA&Two(2)SASCables
• X10DRL-iT:Six(6)SATACables
MNL-1620 -QRG
© 2014 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
MNL-1620-QRG
• One(1)I/OShield
• One(1)QuickReferenceGuide
Revision1.0
A. VGA Port D. USB 3.0 Port 13 G. 10Gb LAN Port 3*
B. IPMI Port E. 1Gb LAN Port 1 H. 10Gb LAN Port 4*
C. USB 3.0 Port 12 F. 1Gb LAN Port 2 I. UID Switch / UID LED
SAN MAC
BIOS LICENSE
SAS CODE
MAC CODE
IPMI CODE
BAR CODE
UID
LEDPWR
LEDBMC
JUSBRJ45
FAN6
FAN5
FAN1
FANB
FAN2
FAN3
FAN4
FANA
JIPMB1
JNVI2C1
JVRM2
JPTG1
1
JPB1
3
JPF1
JPF2
JPG1
JBR1
JPME2
JI2C1
JI2C2
JPS1
JPL2
JPL1
JVRM1
JWD1
J24
1
13
1224
1
J7J5
JS18
JF1
JPWR2
JPWR1
1
JL1
J21
JPI2C1
24
JPS7
SP1
BT1
+
JLAN3
JUIDB1
JSD1
JS1
JSTBY1
I-SGPIO1
I-SGPIO2
J25
JTPM1
JVGA
JLAN1
JBT1
I2C BUS FOR PCI-E SLOT
1-2:ENABLE
2-3:DISABLE
X10DRL-CT
DESIGNED IN USA
REV:1.00
CHASSIS INTRUSION
JL1
2-3:DISABLE
1-2:ENABLE
JI2C1/JI2C2
1-2:NORMAL
2-3:BIOS RECOVERY
JBR1
2-3:ME MANUFACTURING MODE
JPME2
1-2:NORMAL
1-2 ENABLE
JPL2 LAN
2-3 DISABLE
JPL1/
JPI2C1:PWR I2C
JPG1:VGA
JPB1:BMC
2-3 DISABLE
1-2 ENABLE
2-3 DISABLE
1-2 ENABLE
JPTG1:10Gb LAN
2-3 DISABLE
1-2 ENABLE
JPS1:SAS
L-SAS0-3
L-SAS4-7
USB8/9(3.0)
PCI-E 3.0 X8
LAN4
LAN3
LAN1
USB12/13(3.0)
I-SATA0
I-SATA1
I-SATA2
I-SATA3
USB2/3
USB4
JTPM1:TPM/PORT80
CHASSIS INTRUSION
I-SATA4
CMOS CLEAR
I-SATA5
CPU2 SLOT4
SPEAKER-PIN 4-7
JD1:
PWR LED-PIN 1-3
2-3:NMI
JWD1:WATCH DOG
1-2:RST
CPU1 SLOT5 PCI-E 3.0 X16
CPU1 SLOT6 PCI-E 3.0 X8
RSTPWR
ON
JF1
P1-DIMMD1
P1-DIMMC1
X NICOH/
2FF
HDDNIC
LED1
PWR
LED
NMIX
P2-DIMMF1
P2-DIMME1
CPU2
VGA
CPU1
P1-DIMMB1
P1-DIMMA1
P2-DIMMH1
P2-DIMMG1
COM1
IPMI_LAN
LAN2
JD1
The X10DRL-CT/-iT/-C Motherboard supports up to 512 GB of DDR4 Registered
(RDIMM)/Load Reduced (LRDIMM) ECC 2133/1866/1600 MHz memory modules
in eight DIMM slots. Memory speed support is dependent on the CPUs used in the
motherboard. Note: For memory optimization, use only DIMM modules that have been validated
by Supermicro. For the latest memory updates, please refer to our website at http://www.supermicro.
com/products/motherboard.
Motherboard Layout and Features
Jumpers, Connectors and LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Back Panel I/O Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
= mounting hole
A
B
C
D
E
F
G
H
I
Note: Up to 512GB of memory are supported. See chapter 2 of the User Manual for complete
memory population information.
DIMM Memory Installation
LGA 2011
I/O BACK PANEL
Intel E5-2600 V3
Front Panel Control (JF1)
CPU Installation
OPEN 1st
Screw #2
Screw #3
Screw #4
Align Socket Keys
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
Power Fail LED
HDD LED
Power LED
#3~4
#1~2
Vcc
Vcc/UID Switch
Vcc
Vcc/Blue UID LED
Ground
Ground
1920
Vcc
X
Ground
NMI
X
Vcc
NIC2 LED
Heatsink Installation
LGA 2011
Intel E5-2600 V3
Jumpers
Jumper Description Default
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 Onboard VGA Enable Pins 1-2 (Enabled)
JBR1 BIOS Recovery Mode Pins 1-2 (Normal)
JPME2 Intel ME Recovery Mode Pins 1-2 (Normal)
JBT1 Clear CMOS (See Chpt. 2)
JPS1 SAS Enable* Pins 1-2 (Enabled)
JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)
JPL1, JPL2 LAN1, LAN2 Enable/Disable Pins 1-2 (Enabled)
JPTG1 10Gb LAN Support Enable/Disable* Pins 1-2 (Enabled)
JI2C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Disabled)
Connectors and Switches
Connector Description
I/O Back Panel See Back Panel I/O Connectors, below right
COM1 On board Serial port header for COM1
JL1 Chassis Intrusion Header
I-SATA0~5 SATA Interface for SATA1, 2, 3, 4, 5 and 6
USB 2/3 USB 2.0 Header for USB ports 2/3
JSD1 Power Connector for DOM (Disk on Module) Device
USB 8/9 (3.0) USB 3.0 Header for USB ports 8/9
USB4 USB 2.0 Type A port for USB 4
JF1 Front Panel Control/LED Header
FAN1~6, FANA/B CPU/System Fan Headers
L-SAS0~3, L-SAS4~7 L-SAS Interface for SAS0~7**
JTPM1 TPM (Trusted Platform Module) / Port 80 Header
I-SGPIO1/I-SGPIO2 Serial General Purpose I/O Headers 1 and 2
JD1 Speaker/Power LED
JS18 LSISAS3108 TFM connector
JIPMB1 System Management Bus header
JSTBY1 Standby Power Connector
JUIDB1 UID (Unit ID) Switch
JNVI2C1 PCI-E NVMe AOC I2C Header
JPWR1, JPWR2 8-pin ATX Power Connectors
JPI2C1 Power Supply SMBus I2C Header
J24 24-pin ATX Power Connector
LED Indicators
LED Description Color/State Status
LEDPWR Onboard Power LED Green/Solid System Power On
LEDBMC BMC Heartbeat LED Green/Blinking BMC Normal
UID UID Switch Indicator Blue/Steady UID Switch is On
Model 10Gb LAN Support SAS Support
X10DRL-CT Yes Yes
X10DRL-C No Yes
X10DRL-iT Yes No
Supported Motherboard Features
*Note: Refer to the table below for supported features.
CPU Support
Dual Intel
®
E5-2600V3 Series processors (Socket R3-LGA 2011); each processor
supports dual full-width Intel QuickPath Interconnect (QPI) links (of up to 9.6 GT/s
one direction per QPI)
Release Tabs
Notches
*X10DRL-CT/-iT only
Screw #1
Speed (MT/s)
Voltage (V)